[mythtv] what does "DVBRec(1): PID 0x840 discontinuity detected" mean?

[Steven Adeff]

On 10/3/06, Steven Adeff <adeffs.mythtv at gmail.com> wrote:
> On 10/3/06, Stuart Auchterlonie <stuarta at squashedfrog.net> wrote:
> > On Tue, Oct 03, 2006 at 08:06:21AM -0400, Steven Adeff wrote:
> > > >
> > > > It's in quite a fundamental area of the packet processing,
> > > > so i'm going to await further reports for a while before
> > > > considering it for inclusion.
> > >
> > > is there a way to tell if the issue is with the signal the card is
> > > receiving or something internal to the computer?  I'm just having a
> > > hard time understanding why this would randomly start happening and
> > > the cable line looks to be clean?
> > >
> > > It also seems to occur more during heavy i/o load, though this is more
> > > a casual observance. When all three of my HD recorders are going it
> > > seems to be more of an issue than when just one is.
> > >
> >
> > Sounds like you may be running into limitations with
> > 1) PCI bus maximum throughput
> > 2) I/O throughput to your storage
> >
> > also check your dmesg and see if any errors are being thrown
> > by the driver. verify also that each card has it's own interrupt.
>
> Stuart, thanks for helping me with this. Some "answers" to your questions...
>
> I/O: I've been using the same RAID10 setup with no changes for months
> now. I wonder if perhaps fragmentation on my recordings drive is
> slowing it down now to the point of being an issue? I run XFS, I don't
> know if its something that can be an issue with XFS? I discovered
> xfs_fsr well into having a full recording drive, so I don't use it.
> perhaps I should erase all watched recordings that I can to empty the
> drive out and then begin doing a defrag process?
>
> IRQ:
> Subsystem: Hauppauge computer works Inc. WinTV PVR 150
> Flags: bus master, medium devsel, latency 64, IRQ 225
> Memory at e8000000 (32-bit, prefetchable) [size=64M]
> Capabilities: [44] Power Management version 2
>
> Subsystem: pcHDTV pcHDTV HD3000 HDTV
> Flags: bus master, medium devsel, latency 32, IRQ 10
> Memory at f9000000 (32-bit, non-prefetchable) [size=16M]
> Capabilities: [44] Vital Product Data
> Capabilities: [4c] Power Management version 2
>
> Subsystem: pcHDTV pcHDTV HD3000 HDTV
> Flags: bus master, medium devsel, latency 32, IRQ 217
> Memory at fa000000 (32-bit, non-prefetchable) [size=16M]
> Capabilities: [4c] Power Management version 2
>
> Subsystem: Avermedia Technologies Inc AVerTVHD MCE A180
> Flags: bus master, medium devsel, latency 32, IRQ 233
> Memory at fbffe000 (32-bit, non-prefetchable) [size=2K]
> Capabilities: [40] Power Management version 2
>
> Subsystem: Avermedia Technologies Inc AVerTVHD MCE A180
> Flags: bus master, medium devsel, latency 32, IRQ 225
> Memory at fbfff000 (32-bit, non-prefetchable) [size=2K]
> Capabilities: [40] Power Management version 2
>
> it looks like one of my A180's and my PVR150 are on the same IRQ.
>
> In my kern.log I seem to be getting a lot of
> Oct  2 21:29:32 mythbox kernel: cx88[0]/2: queue is empty - first active
> Oct  2 21:29:32 mythbox kernel: cx88[0]/2: cx8802_start_dma w: 0, h: 0, f: 2
> Oct  2 21:29:32 mythbox kernel: cx88[0]/2: setting the interrupt mask
> Oct  2 21:29:32 mythbox kernel: cx88[0]/2: [ffff81003a356200/0]
> cx8802_buf_queue - first active
> Oct  2 21:29:32 mythbox kernel: cx88[0]/2: cx8802_restart_queue
> Oct  2 21:29:32 mythbox kernel: cx88[0]/2: cx8802_restart_queue: queue is empty
> Oct  2 21:29:32 mythbox kernel: cx88[0]/2: queue is empty - first active
> Oct  2 21:29:32 mythbox kernel: cx88[0]/2: cx8802_start_dma w: 0, h: 0, f: 2
> Oct  2 21:29:32 mythbox kernel: cx88[0]/2: setting the interrupt mask
> Oct  2 21:29:32 mythbox kernel: cx88[0]/2: [ffff810012f8aa00/0]
> cx8802_buf_queue - first active
> Oct  2 21:29:33 mythbox kernel: cx88[0]/2: cx8802_restart_queue
> Oct  2 21:29:33 mythbox kernel: cx88[0]/2: cx8802_restart_queue: queue is empty
> Oct  2 21:29:33 mythbox kernel: cx88[0]/2: queue is empty - first active
> Oct  2 21:29:33 mythbox kernel: cx88[0]/2: cx8802_start_dma w: 0, h: 0, f: 2
> Oct  2 21:29:33 mythbox kernel: cx88[0]/2: setting the interrupt mask
> Oct  2 21:29:33 mythbox kernel: cx88[0]/2: [ffff810015f3be00/0]
> cx8802_buf_queue - first active
> Oct  2 22:01:30 mythbox kernel: cx88[0]/2: cx8802_restart_queue
> Oct  2 22:01:30 mythbox kernel: cx88[0]/2: cx8802_restart_queue: queue is empty
>
> let me know if you see anything that jumps out at you that I should
> look into/etc.

did a quick google that lead me to discover my two PATA drives in my
RAID were running
IO_support   =  0 (default 16-bit)
instead of
IO_support   =  1 (32-bit)

and unmaskirq was also off...
so I made those right. time to see what happens...

-- 
Steve
Before you ask, read the FAQ!
http://www.mythtv.org/wiki/index.php/Frequently_Asked_Questions
then search the Wiki, and this list,
http://www.gossamer-threads.com/lists/mythtv/
Mailinglist etiquette -
http://www.mythtv.org/wiki/index.php/Mailing_List_etiquette