[mythtv-users] save position not working with pvr-250 seems OK withwintv

[Richard S]

Sorry for the double post not. Please use other e-mail same title. I have to 
figure out why my system is sending twice.


>From: "Richard S" <anewbeginning2004 at hotmail.com>
>Reply-To: Discussion about mythtv <mythtv-users at mythtv.org>
>To: mythtv-users at mythtv.org
>Subject: [mythtv-users] save position not working with pvr-250 seems OK 
>withwintv
>Date: Mon, 05 Jan 2004 12:49:21 -0500
>
>This is my first post here at mythtv so first let me thank everyone for the 
>great information here, the mythtv program and its great features. I tried 
>to find the answer to this but it seems out of my league. I am also new to 
>linux so I will try my best to describe the problem. YES I have had help 
>getting things working.
>
>I have two mythtv systems set up. One is my everyday system and uses a 
>PVR-250 and the other is my learning system and uses a hauppauge wintv 
>card. Both run great but I have a problem with my PVR-250 setup that is not 
>a problem with my wintv setup.
>
>Problem:
>I can not save the position of a recorded program I am watching when on my 
>PVR-250 system but as I said it works perfectly on my wintv system. Have 
>tried many options from the setup including not using "always prompt". The 
>enter/spacebar does toggle the words "cleared position" and "set position". 
>I did find that if I set a program to record and then go watch it while its 
>recording using  "watch recordings"  the save position works fine until the 
>recording is fully completed then for future watching the save position 
>does not work.
>
>Have the same problem with 0.11 and now I upgraded to the CVS on 1/04/2004 
>and still have the same problem. The wintv system works fine 0.11, 0,12, 
>0.13 and CVS.
>
>Working system:
>OS: Gentoo
>Have mythtv only installed at the moment no other modules
>Hauppauge wintv
>Keyboard only
>PC monitor only watching
>
>Problem system
>OS: Gentoo
>Have Mythweb installed and running.
>Have a serial port IR remote working
>Using nvidia video out (geforce2 gts 32meg) to my TV NTSC. I used NVTV to 
>set overscan.
>
>PVR-250 with the following settings:
>
>Set in mythtv settings "recording profiles"
>Stream type tried DVD (Type 10) and mpeg2 FS (type 0) tried both
>Bitrate 6000, max 15000 (also tried 4500, max 6000)
>Resolution 640x480 (also tried 480x480)
>
>Set using the following commands
>/root/ivtv/utils/test_ioctl -c dnr_mode=3
>/root/ivtv/utils/test_ioctl -y brightness=140
>/root/ivtv/utils/test_ioctl -y contrast=80
>/root/ivtv/utils/test_ioctl -y saturation=63
>/root/ivtv/utils/test_ioctl -y hue=7
>
>Can't seem to find the answer appreciate the help.
>
>_________________________________________________________________
>Check your PC for viruses with the FREE McAfee online computer scan.  
>http://clinic.mcafee.com/clinic/ibuy/campaign.asp?cid=3963
>
>_______________________________________________
>mythtv-users mailing list
>mythtv-users at mythtv.org
>http://mythtv.org/cgi-bin/mailman/listinfo/mythtv-users

_________________________________________________________________
Get reliable dial-up Internet access now with our limited-time introductory 
offer.  http://join.msn.com/?page=dept/dialup