[mythtv-users] RE: Pixelview BT878P+
Tony Harmelink
Ace at Acescrypt.us
Thu Jul 8 23:14:17 EDT 2004
-----BEGIN PGP SIGNED MESSAGE-----
Hash: SHA1
On Thursday 08 July 2004 19:54, you wrote:
> Tony Harmelink wrote:
> > -----BEGIN PGP SIGNED MESSAGE-----
> > Hash: SHA1
> >
> > On Thursday 08 July 2004 16:17, David Wadler wrote:
> >>>I have been trying to get my Pixelview BT878P+ working with Mythtv. i
> >>>have the bttv drivers in the kernel autoloading at boot, the card set-up
> >>>as a V4L card in MythTv setup. But i still don't get any video. Any
> >>>help appreciated.
> >>>
> >>>Specs:
> >>>Athlon 2700+
> >>>ECS KT600-A
> >>>512 MB Kingston
> >>>200GB Hitachi
> >>>Pixelview BT878P+
> >>>Riva TNT2
> >>
> >>I am using a BT878 videocard. Not identical, but close enough to help
> >> you troubleshoot, I hope. What kernel are you running? What version of
> >> Linux? Do you have a /dev/video0? Can you post the results of lsmod?
> >>
> >>-David
> >
> > I am running on Gentoo with a 2.6.7-gentoo-r8 kernel
> > i can see a /dev/video0
> > lsmod
> >
> > nvidia 4818484 0
> > via82cxxx_audio 27208 0
> > ac97_codec 17100 1 via82cxxx_audio
> > snd_bt87x 12040 1
> > snd_via82xx 25508 3
> > snd_ac97_codec 66884 1 snd_via82xx
> > snd_mpu401_uart 6912 1 snd_via82xx
> > snd_rawmidi 21668 1 snd_mpu401_uart
> > snd_seq_oss 33472 0
> > snd_seq_midi_event 6848 1 snd_seq_oss
> > snd_seq 53776 4 snd_seq_oss,snd_seq_midi_event
> > snd_seq_device 7240 3 snd_rawmidi,snd_seq_oss,snd_seq
> > snd_pcm_oss 50472 0
> > snd_pcm 89732 4 snd_bt87x,snd_via82xx,snd_pcm_oss
> > snd_page_alloc 9480 3 snd_bt87x,snd_via82xx,snd_pcm
> > snd_timer 23172 2 snd_seq,snd_pcm
> > snd_mixer_oss 18240 1 snd_pcm_oss
> > snd 50852 20
> > snd_bt87x,snd_via82xx,snd_ac97_codec,snd_mpu401_uart,snd_rawmidi,snd_seq_
> >oss,snd_seq_midi_event,snd_seq,snd_seq_device,snd_pcm_oss,snd_pcm,snd_time
> >r,snd_mixer_oss bttv 144332 0
> > soundcore 8224 3 via82cxxx_audio,snd,bttv
> > msp3400 22036 0
> > - --
> > It's not my fault the earth is flying around a giant nuclear explosion in
> > the sky!
> > -----BEGIN PGP SIGNATURE-----
> > Version: GnuPG v1.2.4 (GNU/Linux)
> >
> > iD8DBQFA7cDtOLEFNzeo/RwRAvMpAKCBSVYXnR13sdpaN9UY2zfmmCovFACfUZ6G
> > XHxQnavLtD84cd0QgqhK3Aw=
> > =Iaa4
> > -----END PGP SIGNATURE-----
> > _______________________________________________
> > mythtv-users mailing list
> > mythtv-users at mythtv.org
> > http://mythtv.org/cgi-bin/mailman/listinfo/mythtv-users
> >
> > .
>
> what is bttv being detected as????
> use
> dmesg | grep bttv
> to find out.
>
> Also, what version of the bt878P+ card are you using? It is printed on
> the pcb.
>
> I would recommend these module options for bttv (from my rev 9d (or
> something like that card)
>
> card=72 tuner=2
Excuse the noob question, but how do i edit the module options for bttv?
The card is a revision 9D
The results of dmesg | grep bttv
bttv: driver version 0.9.14 loaded
bttv: using 8 buffers with 2080k (520 pages) each for capture
bttv: Bt8xx card found (0).
bttv0: Bt878 (rev 17) at 0000:00:0a.0, irq: 18, latency: 32, mmio: 0xdc000000
bttv0: using: *** UNKNOWN/GENERIC *** [card=0,autodetected]
bttv0: gpio: en=00000000, out=00000000 in=00ffc0ff [init]
bttv: readee error
bttv0: using tuner=-1
bttv0: i2c: checking for MSP34xx @ 0x80... not found
bttv0: i2c: checking for TDA9875 @ 0xb0... not found
bttv0: i2c: checking for TDA7432 @ 0x8a... not found
bttv0: registered device video0
bttv0: registered device vbi0
- --
It's not my fault the earth is flying around a giant nuclear explosion in the
sky!
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.2.4 (GNU/Linux)
iD8DBQFA7g2TOLEFNzeo/RwRAg98AJ44bc2GjCUDXOcl5hbH5PxfOCXLvgCgg/me
CtHBsw+gLvXbil91oxToH9Q=
=+AWS
-----END PGP SIGNATURE-----
More information about the mythtv-users
mailing list