[mythtv-users] No input sound on PVR-250
Ryan Allen
ryan at the-summit.net
Mon Jun 21 17:26:27 EDT 2004
This sounds a lot like my problem I just resolved last night. I think
you even posted on the thread on mysettopbox.tv
Anyhow, here is a link to the discussion and what I had to do to fix it.
Good luck! I hope your problem is the same as mine. Keep me informed!
- Ryan
http://mysettopbox.tv/phpBB2/viewtopic.php?t=1777
* John OKeefe <john at terminalreality.com> wrote on [06-21-04y 14:09]:
> When I try to record a T.V. show or watch Live T.V. in
> KnoppMyth R4V4 I hear no sound. Here is the system I
> have
>
> PVR-250 with DirectTV satellite TV-Out COAX connected
> to the COAX in on the PVR-250.
> VIA AC97 sound out connected to headphones.
> P4 1.4Ghz
> Elite P4VMXS motherboard
> 1GB ram
>
> These are the steps I have tried to resolve the
> problem:
>
> (1) I played a MP3 to verify it was not my sound out
> that was not working. I heard sound, so my sound out
> is working great. Sound out is coming from AC97 on
> board audio.
> (2) I ran alsamixer and made sure that all channels
> had volume and that none of the channels had MM (mute)
> above them.
> (3) I ran mythtv-setup and tried all the different
> sound processor options i.e. dsp, dsp0, dsp1, dsp2,
> and dsp3.
> (4) I tried test_ioctl and made sure that volume was
> 65000 and mute was 0.
> (5) I tried the following:
>
> Code:
>
> cd /usr/src
> # The ivtv compile needs the src files.
> tar xvfj linux-2.4.25-chw.tar.bz2
>
> cd /usr/local/lib/ivtv/driver
> make clean
> # I suppose I could have used "make install" but I was
> testing
> # and didn"t want to add to my problems.
> make
>
> cp msp3400.o
> /lib/modules/2.4.25-chw/kernel/drivers/media/video/
> # And answer yes to overwrite the existing file.
>
> I tried mplayer /dev/video0
>
> When I played Mplayer I noticed the following two
> items displayed:
>
> MPEG: No audio stream found -> no sound
>
> and later on down
>
> Audio: no sound
>
> I also tried a couple of the following:
>
> test_ioctl -v input=X,output=Y
>
> Where X and Y are numbers that I try differently each
> time. I have no clue what numbers to use, what range
> of numbers to use, and if I need to reboot each time
> or not.
>
> Is there anyway to check and see what dsp my PVR-250
> is using i.e. dsp, dsp0, dsp1, etc. without having to
> guess?
>
> Each time I change the dsp using mythtv-setup do I
> need to reboot?
>
> How can I verify that there are no other msp3400.o
> files and that the right one is loading?
>
> When running Mplayer does the "MPEG: No audio stream
> found -> no sound" line give any tips as to what might
> be going wrong?
>
> Is there anything else I should try or that I missed
> to get sound input working?
>
> Any help would be much appreciated! I am so close to
> being able to record shows on my KnoppMyth box.
>
> Also I am a super Linux novice so if you give any
> instructions please be detailed as I may not
> understand the command to do what you are asking me to
> do.
>
> Best Regards,
> John
> _______________________________________________
> mythtv-users mailing list
> mythtv-users at mythtv.org
> http://mythtv.org/cgi-bin/mailman/listinfo/mythtv-users
--
+-------------------------------+
| ryan at the-summit.net |
| http://www.pnwtripreports.com |
+-------------------------------+
More information about the mythtv-users
mailing list