[mythtv-users] New Problem with LIRC and Tivo remote...
Nate Thompson
natet at buckeye-express.com
Mon Mar 22 22:23:32 EST 2004
OK, after looking at the messages I was getting from /var/log/messages, I
decided that maybe my lircd.conf file wasn't correct. I downloaded an
updated one (TIVO34) and put it in the proper directory. /usr/bin/irw still
does not work properly, but below is the revised message found in
/var/log/messages. Do I need to somewhere tell LIRC that it should be using
COM1 (i.e. the serial port)? Again, any help greatly apprechiated.
Mar 22 22:17:11 localhost lircd 0.7.0pre1[9590]: lircd(any) ready
Mar 22 22:17:11 localhost lircd: lircd startup succeeded
Mar 22 22:17:18 localhost su(pam_unix)[6446]: session closed for user root
Mar 22 22:17:20 localhost lircd 0.7.0pre1[9590]: accepted new client on
/dev/lircd
Mar 22 22:17:20 localhost lircd 0.7.0pre1[9590]: could not open /dev/lirc
Mar 22 22:17:20 localhost lircd 0.7.0pre1[9590]: default_init(): No such
device
Mar 22 22:17:20 localhost lircd 0.7.0pre1[9590]: caught signal
Nate Thompson
________________________________
From: mythtv-users-bounces at mythtv.org
[mailto:mythtv-users-bounces at mythtv.org] On Behalf Of Nate Thompson
Sent: Monday, March 22, 2004 8:38 PM
To: 'Discussion about mythtv'
Subject: [mythtv-users] New Problem with LIRC and Tivo remote...
Hello all,
I got another PVR-250 and this one seems to work so I went on to the next
step in Jarod's guide. Unfortunately I have hit another snag with getting
LIRC to work properly. Everything has installed properly (following the
directions given in the guide). However, when I try '/usr/bin/irw', it
immediately dumps me back to the prompt. Checking the /var/log/messges file,
I found the following information:
Mar 22 20:07:23 localhost lircd: lircd startup succeeded
Mar 22 20:07:27 localhost lircd 0.7.0pre1[3610]: accepted new client on
/dev/lircd
Mar 22 20:07:27 localhost lircd 0.7.0pre1[3610]: could not get hardware
features
Mar 22 20:07:27 localhost lircd 0.7.0pre1[3610]: this device driver does not
support the new LIRC interface
Mar 22 20:07:27 localhost lircd 0.7.0pre1[3610]: major number of /dev/lirc
is 4
Mar 22 20:07:27 localhost lircd 0.7.0pre1[3610]: LIRC major number is 61
Mar 22 20:07:27 localhost lircd 0.7.0pre1[3610]: check if /dev/lirc is a
LIRC device
Mar 22 20:07:27 localhost lircd 0.7.0pre1[3610]: caught signal
If I check the status of the lircd service (/sbin/service lircd status), I
get 'lircd dead but subsys locked' in response. I am using a homebrew serial
IR receiver that works with WinLIRC on my Windows PC. I have loaded the tivo
lircd.conf file into the /etc directory. I did a search of the mailing list
and while I found people with similar issues, I never really caught a
solution. Any help would definitely be apprechiated.
Thanks,
Nate Thompson
More information about the mythtv-users
mailing list