[mythtv-users] PVR-350 - X via tv-out - tveeprom
John Harvey
john.p.harvey at btinternet.com
Wed Jan 26 18:06:41 EST 2005
Try changeing option "ivtv" to option "fbdev" in the x config
I think it also needs to be /dev/fb1
John
> -----Original Message-----
> From: mythtv-users-bounces at mythtv.org [mailto:mythtv-users-
> bounces at mythtv.org] On Behalf Of dead
> Sent: 26 January 2005 22:24
> To: mythtv-users at mythtv.org
> Subject: [mythtv-users] PVR-350 - X via tv-out - tveeprom
>
> Greetings,
>
> I followed jarod's MythTV on FC3 guide.
>
> After much tinkering I finally got X working over the TV-out for the
> pvr-350 running on a fully updated FC3 system. I found the fix for the
> tveeprom Error -19 that was occuring (adding the alias in modprobe.conf)
> but now X over pvr-350's tv-out no longer works after adding that alias.
>
> I've also never been able to get it to recognize the cable signal
> (tuner0 / input type = 4) and be able to change channels, though it did
> seem to work piping S-video (svideo0 / input type 6 I think). I'm using
> coax cable from the wall that I know works (it works when I plug it into
> my tivo). The end result I'm after is to be able to replace my tivo with
> my mythtv box, and put another tuner card into it to be able to record 2
> shows at once. Just getting it working with 1 tuner is the current goal.
>
> I've done a bit of reading through the various online documentation and
> mailing lists, but I can't seem to get it quite right.
>
>
> I'm using the following RPMs installed from atrpms:
>
> -- start rpm -qa output --
> [root at localhost ~]# rpm -qa | grep myth
> mythtv-frontend-0.16-82.2.rhfc3.at
> mythtv-theme-purplegalaxy-0.20031214-3.at
> mythtv-theme-MediaCenter-0.17-3.at
> mythmusic-0.16-61.rhfc3.at
> mythnews-0.16-31.rhfc3.at
> mythvideo-0.16-58.rhfc3.at
> mythtv-0.16-82.2.rhfc3.at
> mythtv-theme-gant-0.pr1-2.at
> mythtv-theme-abstract-0.20040910-2.at
> mythtv-theme-sleek-0.35-2.at
> mythtvsetup-0.16-82.2.rhfc3.at
> mythmkmovie-1.0.1-3.rhfc3.at
> mythdvd-0.16-42.rhfc3.at
> mythtv-backend-0.16-82.2.rhfc3.at
> mythtv-themes-0.16-82.2.rhfc3.at
> mythbrowser-0.16-25.rhfc3.at
> mythgallery-0.16-61.rhfc3.at
> mythtv-theme-visor-0.16.2-5.at
> mythweather-0.16-58.rhfc3.at
> mythtv-suite-0.16-45.at
> mythtv-theme-photo-4-6.at
> mythgame-0.16-60.rhfc3.at
> mythweb-0.16-63.at
> libmyth-0.16-82.2.rhfc3.at
> mythtv-theme-isthmus-0.20040804-1.at
> mythphone-0.16-2.rhfc3.at
> [root at localhost ~]# rpm -qa | grep ivtv
> ivtv-kmdl-2.6.10-1.741_FC3-0.3.2c-66.rhfc3.at
> ivtv-firmware-dec-2.02.023-4.at
> ivtv-kmdl-2.6.10-1.741_FC3-0.1.10-49.1_pre2_ck100zz.rhfc3.at
> ivtv-firmware-1.8a-4.at
> perl-Video-ivtv-0.13-6.rhfc3.at
> ivtv-0.3.2c-66.rhfc3.at
> ivtv-firmware-enc-2.04.024-4.at
> ivtvdev-0.8-1.rhfc3.at
> [root at localhost ~]# rpm -qa | grep lirc
> lirc-0.7.0-43.1.rhfc3.at
> lirc-kmdl-2.6.10-1.741_FC3-0.7.0-43.1.rhfc3.at
> lirc-lib-0.7.0-43.1.rhfc3.at
> lirc-devices-0.7.0-1.rhfc3.at
> [root at localhost ~]# rpm -qa | grep video4linux
> video4linux-20050113_172233-54.1.rhfc3.at
> video4linux-kmdl-2.6.10-1.741_FC3-20050113_172233-54.1.rhfc3.at
> -- end rpm -qa output --
>
> Here is the error from Xorg.0.log
>
> -- start Xorg.0.log snippet --
> (II) IVTVDEV: driver for framebuffer: PVR-350
> (II) Primary Device is: PCI 01:00:0
> (--) Chipset PVR-350 found
> (EE) ivtvHWProvbe failed to do IVTVFB_IOCTL_GET_STATE for device (null)
> (EE) Screen 0 deleted because of no matching config section.
> (II) UnloadModule: "ivtvdev"
> (EE) Device(s) detected, but none match those in the config file.
>
> Fatal server error:
> no screens found
> -- end Xorg.0.log snippet --
>
> More conf files / logs / cmd outputs below:
>
> -- start xorg.conf snippet --
> Section "Monitor"
> Identifier "NTSC Monitor"
> HorizSync 30-68
> VertRefresh 50-120
> Mode "720x480"
> # D: 34.563 MHz, H: 37.244 kHz, V: 73.897 Hz
> DotClock 34.564
> HTimings 720 752 840 928
> VTimings 480 484 488 504
> Flags "-HSync" "-VSync"
> EndMode
> EndSection
>
> Section "ServerFlags"
> Option "blank time" "0"
> Option "standby time" "0"
> Option "suspend time" "0"
> Option "off time" "0"
> EndSection
>
> Section "Device"
> Identifier "Hauppauge PVR 350 iTVC15 Framebuffer"
> Driver "ivtvdev"
> #Driver "fbdev"
>
> ## change fb0 to whatever your card grabbed
> Option "ivtv" "/dev/fb0"
>
> ## change the BusID to whatever is reported by lspci
> BusID "0:10:0"
> EndSection
>
>
> Section "Screen"
> Identifier "Screen0"
> Device "Hauppauge PVR 350 iTVC15 Framebuffer"
> Monitor "NTSC Monitor"
> DefaultDepth 24
> DefaultFbbpp 32
> Subsection "Display"
> Depth 24
> FbBpp 32
> Modes "720x480"
> EndSubsection
>
> EndSection
> -- end xorg.conf snippet --
>
> -- start modprobe.conf --
> alias eth0 via-velocity
> alias snd-card-0 snd-ens1371
> options snd-card-0 index=0
> install snd-ens1371 /sbin/modprobe --ignore-install snd-ens1371 &&
> /usr/sbin/alsactl restore >/dev/null 2>&1 || :
> remove snd-ens1371 { /usr/sbin/alsactl store >/dev/null 2>&1 || : ; };
> /sbin/modprobe -r --ignore-remove snd-ens1371
> alias usb-controller ehci-hcd
> alias usb-controller1 uhci-hcd
> # nvidia kernel module
> alias char-major-195 nvidia-1_0-6629
> # lirc
> alias char-major-61 lirc_i2c
> # ivtv/pvr350 driver module
> alias tveeprom tveeprom-ivtv
> alias char-major-81 videodev
> alias char-major-81-0 ivtv
> install ivtv /sbin/modprobe --ignore-install ivtv; /sbin/modprobe ivtv-fb
> install lirc_i2c /sbin/modprobe ivtv; /sbin/modprobe --ignore-install
> lirc_i2c
> -- end modprobe.conf --
>
> -- start dmesg snippet --
> lirc_dev: no version for "struct_module" found: kernel tainted.
> lirc_dev: IR Remote Control driver registered, at major 61
> Linux video capture interface: v1.00
> ivtv: ==================== START INIT IVTV ====================
> ivtv: version 0.3.2 (c) loading
> ivtv: Linux version: 2.6.10-1.741_FC3 686 REGPARM 4KSTACKS gcc-3.4
> ivtv: In case of problems please include the debug info
> ivtv: between the START INIT IVTV and END INIT IVTV lines when
> ivtv: mailing the ivtv-devel mailinglist.
> ivtv: Autodetected WinTV PVR 350 card
> ivtv: Found an iTVC15 based chip
> ACPI: PCI interrupt 0000:00:0a.0[A] -> GSI 10 (level, low) -> IRQ 10
> ivtv: Unreasonably low latency timer, setting to 64 (was 32)
> ivtv: VIA PCI device: 0x0258 vendor: 0x1106
> tveeprom: Hauppauge: model = 48132, rev = K268, serial# = 2918377
> tveeprom: tuner = LG TAPE H001F MK3 (idx = 68, type = 47)
> tveeprom: tuner fmt = NTSC(M) (eeprom = 0x08, v4l2 = 0x00001000)
> tveeprom: audio_processor = MSP3440 (type = 11)
> ivtv: i2c attach [client=tveeprom[0],ok]
> ivtv: Tuner Type 47, Tuner formats 0x00001000, Radio: yes, Model
> 0x00ad2598, Rev
> ision 0x00000001
> ivtv: NTSC tuner detected
> ivtv: Radio detected
> tuner: chip found at addr 0xc2 i2c-bus ivtv i2c driver #0
> ivtv: i2c attach [client=(tuner unset),ok]
> saa7115: starting probe for adapter SMBus Via Pro adapter at 0400 (0x0)
> saa7115: starting probe for adapter ivtv i2c driver #0 (0x10005)
> saa7115: detecting saa7115 client on address 0x42
> saa7115: writing init values
> ivtv: i2c attach [client=saa7115[0],ok]
> saa7115: status: (1E) 0x48, (1F) 0xc0
> saa7127: Ignoring new-style parameters in presence of obsolete ones
> saa7127: video encoder driver version V 0.3 loaded
> saa7127: detecting saa7127 client on address 0x88
> saa7127: Selecting NTSC video Standard
> saa7127: Selecting S-Video+Composite
> saa7127: Turn WSS off
> saa7127: Widescreen Mode 4:3 Full Format
> saa7127: Selecting Normal Encoder Input
> saa7127: Enable Video Output
> ivtv: i2c attach [client=saa7127[0],ok]
> msp34xx: init: chip=MSP3448W-A2 +nicam +simple +simpler +radio mode=simple
> ivtv: i2c attach [client=MSP3448W-A2,ok]
> msp3410: daemon started
> ivtv: Encoder revision: 0x02040024
> ivtv: Encoder Firmware may be buggy, use version 0x02040011
> ivtv: Decoder revision: 0x02020023
> ivtv: Configuring WinTV PVR 350 card with 10 streams
> ivtv: Create DMA stream 0 using 256 16384 byte buffers 4194304 kbytes
> total
> ivtv: Registered v4l2 device, streamtype 0 minor 0
> ivtv: Create DMA stream 1
> ivtv: Registered v4l2 device, streamtype 1 minor 32
> ivtv: Create stream 2 using 40 52224 byte buffers 2097152 kbytes total
> ivtv: Registered v4l2 device, streamtype 2 minor 224
> ivtv: Create DMA stream 3 using 455 4608 byte buffers 2097152 kbytes
> total
> ivtv: Registered v4l2 device, streamtype 3 minor 24
> ivtv: Create stream 4
> ivtv: Registered v4l2 device, streamtype 4 minor 64
> ivtv: Create DMA stream 5 using 16 65536 byte buffers 1048576 kbytes
> total
> ivtv: Registered v4l2 device, streamtype 5 minor 16
> ivtv: Create stream 6 using 1024 2048 byte buffers 262144 kbytes total
> ivtv: Registered v4l2 device, streamtype 6 minor 228
> ivtv: Create stream 7
> ivtv: Registered v4l2 device, streamtype 7 minor 232
> ivtv: Create DMA stream 8 using 6 103680 byte buffers 622080 kbytes total
> ivtv: Registered v4l2 device, streamtype 8 minor 48
> ivtv: Create DMA stream 9 using 32 65536 byte buffers 2097152 kbytes
> total
> ivtv: Setting Tuner 47
> tuner: type set to 47 (LG NTSC (TAPE series)) by ivtv i2c driver #0
> saa7115: decoder set input (4)
> saa7115: now setting Composite input
> ivtv: Setting audio matrix to input 3, output 1
> ivtv: Switching standard to NTSC.
> saa7115: decoder set norm NTSC
> saa7115: set audio: 0x01
> saa7127: Setting Encoder Video Standard
> saa7127: Set NTSC Video Mode
> saa7127: Selecting NTSC video Standard
> ivtv: ivtv_enc_thread: pid = 4138, itv = 0xe10e9a20
> ivtv: ivtv_dec_thread: pid = 4139, itv = 0xe10e9a20
> ivtv: Initialized WinTV PVR 350, card #0
> ivtv: ==================== END INIT IVTV ====================
> ivtv-osd: Framebuffer module loaded (attached to ivtv card id 0)
> ivtv-osd: Framebuffer is at decoder-relative address 0x00510000 and has
> 1704960
> bytes.
> spurious 8259A interrupt: IRQ7.
> ivtv-osd: screen coords: [0 0] -> [720 480]
> ivtv-osd: original global alpha = 208
> ivtv-osd: current OSD state = 39
> ivtv-osd: new global alpha = 208 (1 255 0)
> ivtv-osd: framebuffer at 0xf5510000, mapped to 0xe1f90000, size 1350k
> ivtv-osd: mode is 720x480x32, linelength=2880
> ivtv-osd: fb1: iTVC15 TV out frame buffer device
> bttv: driver version 0.9.15 loaded
> bttv: using 8 buffers with 2080k (520 pages) each for capture
> lirc_i2c: chip found @ 0x18 (Hauppauge IR)
> ivtv: i2c attach [client=Hauppauge IR,ok]
> lirc_dev: lirc_register_plugin:sample_rate: 10
> -- end dmesg snippet --
>
> -- start ivtvctl stuff --
> [root at localhost ~]# ivtvctl -a
> ioctl: IVTV_IOC_G_CODEC
> Codec parameters
> aspect : 2
> audio : 0x00e9
> bframes : 3
> bitrate_mode: 0
> bitrate : 8000000
> bitrate_peak: 9600000
> dnr_mode : 0
> dnr_spatial : 0
> dnr_temporal: 0
> dnr_type : 0
> framerate : 0
> framespergop: 15
> gop_closure : 1
> pulldown : 0
> stream_type : 0
> ioctl: VIDIOC_G_FMT
> Type : Video Capture
> Width : 720
> Height : 480
> ioctl: VIDIOC_QUERYCAP
> Driver name : ivtv
> Card type : Vanilla iTVC15 card
> Bus info : 0
> Driver version: 770
> Capabilities : 0x01070033
> ioctl: VIDIOC_ENUMINPUT
> Input : 0
> Name : Composite 0
> Type : 0x00000002
> Audioset: 0x00000003
> Tuner : 0x00000000
> Standard: 0x00000000007F3FFF ( PAL NTSC SECAM )
> Status : 0
>
> Input : 1
> Name : Composite 1
> Type : 0x00000002
> Audioset: 0x00000003
> Tuner : 0x00000000
> Standard: 0x00000000007F3FFF ( PAL NTSC SECAM )
> Status : 0
>
> Input : 2
> Name : Composite 2
> Type : 0x00000002
> Audioset: 0x00000003
> Tuner : 0x00000000
> Standard: 0x00000000007F3FFF ( PAL NTSC SECAM )
> Status : 0
>
> Input : 3
> Name : Composite 3
> Type : 0x00000002
> Audioset: 0x00000003
> Tuner : 0x00000000
> Standard: 0x00000000007F3FFF ( PAL NTSC SECAM )
> Status : 0
>
> Input : 4
> Name : Tuner 0
> Type : 0x00000001
> Audioset: 0x00000003
> Tuner : 0x00000000
> Standard: 0x0000000000003000 ( NTSC )
> Status : 0
>
> Input : 5
> Name : Composite 4
> Type : 0x00000002
> Audioset: 0x00000003
> Tuner : 0x00000000
> Standard: 0x00000000007F3FFF ( PAL NTSC SECAM )
> Status : 0
>
> Input : 6
> Name : S-Video 0
> Type : 0x00000002
> Audioset: 0x00000003
> Tuner : 0x00000000
> Standard: 0x00000000007F3FFF ( PAL NTSC SECAM )
> Status : 0
>
> Input : 7
> Name : S-Video 1
> Type : 0x00000002
> Audioset: 0x00000003
> Tuner : 0x00000000
> Standard: 0x00000000007F3FFF ( PAL NTSC SECAM )
> Status : 0
>
> Input : 8
> Name : S-Video 2
> Type : 0x00000002
> Audioset: 0x00000003
> Tuner : 0x00000000
> Standard: 0x00000000007F3FFF ( PAL NTSC SECAM )
> Status : 0
>
> Input : 9
> Name : S-Video 3
> Type : 0x00000002
> Audioset: 0x00000003
> Tuner : 0x00000000
> Standard: 0x00000000007F3FFF ( PAL NTSC SECAM )
> Status : 0
> ioctl: VIDIOC_G_INPUT
> Input = 4
> ioctl: VIDIOC_ENUMOUTPUT
> Output : 0
> Name : S-Video + Composite
> Type : 0x00000002
> Audioset: 0x00000001
> Standard: 0x00000000007F3FFF ( PAL NTSC SECAM )
>
> Output : 1
> Name : Composite
> Type : 0x00000002
> Audioset: 0x00000001
> Standard: 0x00000000007F3FFF ( PAL NTSC SECAM )
>
> Output : 2
> Name : S-Video
> Type : 0x00000002
> Audioset: 0x00000001
> Standard: 0x00000000007F3FFF ( PAL NTSC SECAM )
>
> Output : 3
> Name : RGB
> Type : 0x00000002
> Audioset: 0x00000001
> Standard: 0x00000000007F3FFF ( PAL NTSC SECAM )
>
> Output : 4
> Name : YUV C
> Type : 0x00000002
> Audioset: 0x00000001
> Standard: 0x00000000007F3FFF ( PAL NTSC SECAM )
>
> Output : 5
> Name : YUV V
> Type : 0x00000002
> Audioset: 0x00000001
> Standard: 0x00000000007F3FFF ( PAL NTSC SECAM )
> ioctl: VIDIOC_G_OUTPUT
> Output = 0
> ioctl: VIDIOC_ENUMAUDIO
> Input : 0
> Name : Tuner Audio In
>
> Input : 1
> Name : Audio Line In
> ioctl: VIDIOC_G_AUDIO
> Input = 0: Tuner Audio In
> ioctl: VIDIOC_G_FREQUENCY
> Frequency = 0
> ioctl: VIDIOC_ENUMSTD
> index : 0
> ID : 0x0000000000003000
> Name : NTSC
> Frame period: 1001/30000
> Frame lines : 525
>
> index : 1
> ID : 0x00000000000000FF
> Name : PAL
> Frame period: 1/25
> Frame lines : 625
>
> index : 2
> ID : 0x00000000007F0000
> Name : SECAM
> Frame period: 1/25
> Frame lines : 625
> ioctl: VIDIOC_G_STD
> Standard = 0x00003000
> ioctl: VIDIOC_QUERYCTRL
> Brightness = 128
> Contrast = 64
> Saturation = 64
> Hue = 0
> Volume = 58880
> Mute = 1
> -- end ivtv stuffs --
>
> Any tips, hints, suggestions, fixes or comments will be much appreciated.
>
> If more info is needed to help diagnose my issues, just ask for it.
>
> Thanks in advance.
>
>
> _______________________________________________
> mythtv-users mailing list
> mythtv-users at mythtv.org
> http://mythtv.org/cgi-bin/mailman/listinfo/mythtv-users
More information about the mythtv-users
mailing list