[mythtv-users] PVR 350 and MythVideo

Duncan Brown mythtv at duncb.co.uk
Fri Jun 17 13:20:24 UTC 2005


Hey

So its Friday, and I'm back to the point I left you last. Just installed 
the latest ivtv and utils by doing a make && make install. Ivtvdev has 
also been installed.

Using xv results in a messed up green/black/purple picture. Also I now 
cannot change channel in live tv. The box goes through the motions, and 
even displays the right channel info, but it doesn't actually change 
channel.

Here is the useful bit from messages

Jun 17 14:08:57 Gobbla kernel: ivtv: ==================== START INIT 
IVTV ====================
Jun 17 14:08:57 Gobbla kernel: ivtv: version 0.3.6 (k) loading
Jun 17 14:08:57 Gobbla kernel: ivtv: Linux version: 2.6.11-1.27_FC3 686 
REGPARM 4KSTACKS gcc-3.4
Jun 17 14:08:57 Gobbla kernel: ivtv: In case of problems please include 
the debug info
Jun 17 14:08:57 Gobbla kernel: ivtv: between the START INIT IVTV and END 
INIT IVTV lines when
Jun 17 14:08:57 Gobbla kernel: ivtv: mailing the ivtv-devel mailinglist.
Jun 17 14:08:57 Gobbla kernel: ivtv: Autodetected WinTV PVR 350 card
Jun 17 14:08:57 Gobbla kernel: ivtv: Found an iTVC15 based chip
Jun 17 14:08:57 Gobbla kernel: ACPI: PCI Interrupt Link [LNKB] enabled 
at IRQ 10
Jun 17 14:08:57 Gobbla kernel: PCI: setting IRQ 10 as level-triggered
Jun 17 14:08:57 Gobbla kernel: ACPI: PCI interrupt 0000:00:09.0[A] -> 
GSI 10 (level, low) -> IRQ 10
Jun 17 14:08:57 Gobbla kernel: ivtv: Unreasonably low latency timer, 
setting to 64 (was 32)
Jun 17 14:08:57 Gobbla kernel: ivtv: VIA PCI device: 0x3099 vendor: 0x1106
Jun 17 14:08:57 Gobbla kernel: ivtv: Failed to load module tveeprom
Jun 17 14:08:57 Gobbla kernel: ivtv: i2c client addr: 0x50 not found for 
command 0!
Jun 17 14:08:57 Gobbla kernel: ivtv: Error -19 reading Hauppauge eeprom.
Jun 17 14:08:57 Gobbla kernel: ivtv: Possible causes: the tveeprom 
module was not loaded, or
Jun 17 14:08:57 Gobbla kernel: ivtv: the eeprom kernel module was loaded 
before the tveeprom module.
Jun 17 14:08:57 Gobbla kernel: tuner: Ignoring new-style parameters in 
presence of obsolete ones
Jun 17 14:08:57 Gobbla kernel: tuner: chip found at addr 0xc2 i2c-bus 
ivtv i2c driver #0
Jun 17 14:08:57 Gobbla kernel: ivtv: i2c attach [client=(tuner unset),ok]
Jun 17 14:08:57 Gobbla kernel: saa7115: starting probe for adapter ivtv 
i2c driver #0 (0x10005)
Jun 17 14:08:57 Gobbla kernel: saa7115: detecting saa7115 client on 
address 0x42
Jun 17 14:08:57 Gobbla kernel: saa7115: writing init values
Jun 17 14:08:57 Gobbla kernel: ivtv: i2c attach [client=saa7115[50],ok]
Jun 17 14:08:57 Gobbla kernel: saa7115: status: (1E) 0x00, (1F) 0xc0
Jun 17 14:08:57 Gobbla kernel: saa7127: Ignoring new-style parameters in 
presence of obsolete ones
Jun 17 14:08:57 Gobbla kernel: saa7127: video encoder driver version V 
0.3 loaded
Jun 17 14:08:57 Gobbla kernel: saa7127: detecting saa7127 client on 
address 0x88
Jun 17 14:08:57 Gobbla kernel: saa7127: Selecting NTSC video Standard
Jun 17 14:08:57 Gobbla rpcidmapd: rpc.idmapd startup succeeded
Jun 17 14:08:57 Gobbla kernel: saa7127: Selecting S-Video+Composite
Jun 17 14:08:57 Gobbla kernel: saa7127: Turn WSS off
Jun 17 14:08:57 Gobbla kernel: saa7127: Widescreen Mode 4:3 Full Format
Jun 17 14:08:57 Gobbla kernel: saa7127: Selecting Normal Encoder Input
Jun 17 14:08:57 Gobbla kernel: saa7127: Enable Video Output
Jun 17 14:08:57 Gobbla kernel: ivtv: i2c attach [client=saa7127[50],ok]
Jun 17 14:08:57 Gobbla kernel: ivtv: Failed to load module msp3400
Jun 17 14:08:57 Gobbla kernel: tda9885/6/7: chip found @ 0x86
Jun 17 14:08:57 Gobbla kernel: ivtv: i2c attach [client=tda9887,ok]
Jun 17 14:08:57 Gobbla kernel: ivtv: Encoder revision: 0x02040024
Jun 17 14:08:57 Gobbla kernel: ivtv: Encoder Firmware may be buggy, use 
version 0x02040011
Jun 17 14:08:57 Gobbla kernel: ivtv: Decoder revision: 0x02020023
Jun 17 14:08:57 Gobbla kernel: ivtv: Configuring WinTV PVR 350 card with 
10 streams
Jun 17 14:08:57 Gobbla kernel: ivtv: Registered v4l2 device, streamtype 
0 minor 0
Jun 17 14:08:57 Gobbla kernel: ivtv: Create DMA stream 0 using 128 16384 
byte buffers  0 kbytes total
Jun 17 14:08:57 Gobbla kernel: ivtv: Registered v4l2 device, streamtype 
1 minor 32
Jun 17 14:08:57 Gobbla kernel: ivtv: Create DMA stream 1 using 161 12960 
byte buffers  0 kbytes total
Jun 17 14:08:57 Gobbla kernel: ivtv: Registered v4l2 device, streamtype 
2 minor 224
Jun 17 14:08:57 Gobbla kernel: ivtv: Create DMA stream 2 using 165 12635 
byte buffers  0 kbytes total
Jun 17 14:08:57 Gobbla kernel: ivtv: Registered v4l2 device, streamtype 
3 minor 24
Jun 17 14:08:57 Gobbla kernel: ivtv: Create DMA stream 3 using 455 4608 
byte buffers  0 kbytes total
Jun 17 14:08:57 Gobbla kernel: ivtv: Registered v4l2 device, streamtype 
4 minor 64
Jun 17 14:08:57 Gobbla kernel: ivtv: Create stream 4
Jun 17 14:08:57 Gobbla kernel: ivtv: Registered v4l2 device, streamtype 
5 minor 16
Jun 17 14:08:57 Gobbla kernel: ivtv: Create DMA stream 5 using 16 65536 
byte buffers  0 kbytes total
Jun 17 14:08:57 Gobbla kernel: ivtv: Registered v4l2 device, streamtype 
6 minor 228
Jun 17 14:08:57 Gobbla kernel: ivtv: Create DMA stream 6 using 1024 2048 
byte buffers  0 kbytes total
Jun 17 14:08:57 Gobbla kernel: ivtv: Registered v4l2 device, streamtype 
7 minor 232
Jun 17 14:08:57 Gobbla kernel: ivtv: Create stream 7
Jun 17 14:08:57 Gobbla kernel: ivtv: Registered v4l2 device, streamtype 
8 minor 48
Jun 17 14:08:57 Gobbla kernel: ivtv: Create DMA stream 8 using 20 51840 
byte buffers  0 kbytes total
Jun 17 14:08:57 Gobbla kernel: ivtv: Create DMA stream 9 using 32 65536 
byte buffers  0 kbytes total
Jun 17 14:08:57 Gobbla kernel: saa7115: decoder set norm PAL
Jun 17 14:08:57 Gobbla kernel: saa7115: set audio: 0x01
Jun 17 14:08:57 Gobbla kernel: saa7115: decoder set input (4)
Jun 17 14:08:57 Gobbla kernel: saa7115: now setting Composite input
Jun 17 14:08:57 Gobbla kernel: ivtv: Setting audio matrix to input 3, 
output 1
Jun 17 14:08:57 Gobbla kernel: ivtv: i2c client addr: 0x40 not found for 
command 1074294033!
Jun 17 14:08:57 Gobbla kernel: ivtv: i2c client addr: 0x40 not found for 
command 2150135312!
Jun 17 14:08:57 Gobbla kernel: ivtv: i2c client addr: 0x40 not found for 
command 1076393489!
Jun 17 14:08:57 Gobbla kernel: ivtv: Switching standard to PAL.
Jun 17 14:08:57 Gobbla kernel: ivtv: i2c client addr: 0x40 not found for 
command 1076917763!
Jun 17 14:08:57 Gobbla kernel: saa7115: decoder set norm PAL
Jun 17 14:08:57 Gobbla kernel: saa7115: set audio: 0x01
Jun 17 14:08:57 Gobbla kernel: saa7127: Setting Encoder Video Standard
Jun 17 14:08:57 Gobbla kernel: saa7127: Set PAL Video Mode
Jun 17 14:08:57 Gobbla kernel: saa7127: Selecting PAL video Standard
Jun 17 14:08:57 Gobbla kernel: ivtv: Initialized WinTV PVR 350, card #0
Jun 17 14:08:57 Gobbla kernel: ivtv: ====================  END INIT 
IVTV  ====================

Any help would be great, i'm totally clueless here

Thanks

Dunc


More information about the mythtv-users mailing list