[mythtv-users] Re: HD3000: Could not find dvb tuning parameters for
transport 0
Mudit Wahal
mwahal at gmail.com
Tue May 17 23:55:55 UTC 2005
The channels for which I'm not able to watch/record, the mplexid,
serviceid, atscrcid are all NULL.
---------------
| chanid | channum | freqid | sourceid | callsign | name |
icon | finetune | videofilters | xmltvid | recpriority | contrast |
brightness | colour | hue | tvformat | commfree | visible |
outputfilters | useonairguide | mplexid | serviceid | atscsrcid |
+--------+---------+--------+----------+----------+------------------+------+----------+--------------+---------+-------------+----------+------------+--------+-------+----------+----------+---------+---------------+---------------+---------+-----------+-----------+
| 1034 | 7_1 | 24-1 | 1 | KGODT | KGODT (KGO-DT) |
none | NULL | | 19574 | 0 | 32768 |
32768 | 32768 | 32768 | Default | 0 | 1 |
| 0 | NULL | NULL | NULL |
| 1036 | 36_1 | 52-1 | 1 | KICUDT | KICUDT (KICU-DT) |
none | NULL | | 21650 | 0 | 32768 |
32768 | 32768 | 32768 | Default | 0 | 1 |
| 0 | NULL | NULL | NULL |
| 1041 | 7_2 | 24-2 | 1 | KGODT2 | KGODT2 (KGO-DT2) |
none | NULL | | 30833 | 0 | 32768 |
32768 | 32768 | 32768 | Default | 0 | 1 |
| 0 | NULL | NULL | NULL |
| 1065 | 65_1 | 41-1 | 1 | KKPXDT | KKPXDT (KKPX-DT) |
none | NULL | | 35375 | 0 | 32768 |
32768 | 32768 | 32768 | Default | 0 | 1 |
| 0 | NULL | NULL | NULL |
+--------+---------+--------+----------+----------+------------------+------+----------+--------------+---------+-------------+----------+------------+--------+-------+----------+----------+---------+---------------+---------------+---------+-----------+-----------+
--------
On 5/17/05, Mudit Wahal <mwahal at gmail.com> wrote:
> Hi,
>
> I'm in San Jose, using HD 3000 for over the air channels. Installed
> Knoppix Myth R5A15.1. I can't watch live TV using the DVB. I dont know
> if others have same issue or not.
>
> cx2388x dvb driver version 0.0.4 loaded
> cx88[0]: subsystem: 7063:3000, board: pcHDTV HD3000 HDTV [card=22,autodetected]
> cx88[0]/2: found at 0000:00:09.2, rev: 5, irq: 17, latency: 32, mmio: 0xe3000000
> cx88[0]/2: cx2388x based dvb card
> DVB: registering new adapter (cx88[0]).
> DVB: registering frontend 0 (pcHDTV HD3000 HDTV)...
> eth0: MII PHY found at address 1, status 0x7869 advertising 05e1 Link 45e1.
> cx2388x v4l2 driver version 0.0.4 loaded
> cx88[0]/0: found at 0000:00:09.0, rev: 5, irq: 17, latency: 32, mmio: 0xe2000000
> tuner 0-0061: chip found @ 0xc2 (cx88[0])
> tuner 0-0061: type set to 52 (Thomson DDT 7610 (ATSC/NTSC))
> cx88[0]/0: registered device video0 [v4l2]
> cx88[0]/0: registered device vbi0
> cx88[0]/0: registered device radio0
> pcHDTV HD3000 driver version 2.0.0 loaded
> cx2388x blackbird driver version 0.0.4 loaded
> or51132: Waiting for firmware upload(dvb-fe-or51132-vsb.fw)...
> or51132: Version: 10001134-19430000 (113-4-194-3)
> or51132: Firmware upload complete.
>
> I can record the programs and then watch them. But I'm having trouble
> watching Channel 7 (ABC). Whenever I tune to record something off 7_1,
> I get the following error messages.
>
> 2005-05-17 09:15:45.801 Started recording "Live With Regis and Kelly"
> on channel: 1034 on cardid: 1, sourceid 1
> 2005-05-17 09:15:45.841 DVB#0 ERROR - Could not find dvb tuning
> parameters for transport 0
> 2005-05-17 09:15:45.845 DVB#0 ERROR - Failed to get channel options
> for channel 7_1.
> 2005-05-17 09:15:46.032 Changing from None to RecordingOnly
> 2005-05-17 09:15:46.182 DVB#0 Recorder: Card opened successfully
> (using TS mode).
> 2005-05-17 09:15:46.207 DVB#0 ERROR - No PIDS set, please correct your
> channel setup.
> 2005-05-17 09:15:47.287 DVB#0 WARNING - No data from card in 1 second.
> 2005-05-17 09:15:48.299 DVB#0 WARNING - No data from card in 1 second.
> 2005-05-17 09:15:49.334 DVB#0 WARNING - No data from card in 1 second.
>
> I created channels.conf using azap. I see the following lines
>
> KGO:533000000:8VSB:0:0
>
> I ran azap -r KGO and got the following
>
> root at mythtvbe:/tftpboot# azap -r KGO
> using '/dev/dvb/adapter0/frontend0' and '/dev/dvb/adapter0/demux0'
> tuning to 533000000 Hz
> video pid 0x0000, audio pid 0x0000
> status 00 | signal 3999 | snr e287 | ber 00000000 | unc 00000000 |
> status 1f | signal da5d | snr fa35 | ber 00000000 | unc 00000000 | FE_HAS_LOCK
> status 1f | signal dcab | snr fa29 | ber 00000000 | unc 00000000 | FE_HAS_LOCK
> status 1f | signal dcab | snr fa07 | ber 00000000 | unc 00000000 | FE_HAS_LOCK
> status 1f | signal da5d | snr fa01 | ber 00000000 | unc 00000000 | FE_HAS_LOCK
> status 1f | signal da5d | snr f9ff | ber 00000000 | unc 00000000 | FE_HAS_LOCK
> status 1f | signal d80f | snr fa07 | ber 00000000 | unc 00000000 | FE_HAS_LOCK
> status 1f | signal dcab | snr fa01 | ber 00000000 | unc 00000000 | FE_HAS_LOCK
>
> Then I ran dvbtraffic and got the following
>
> -PID--FREQ-----BANDWIDTH-BANDWIDTH-
> 0000 9 p/s 1 kb/s 14 kbit
> 0030 9 p/s 1 kb/s 14 kbit
> 0031 8294 p/s 1522 kb/s 12474 kbit
> 0034 280 p/s 51 kb/s 422 kbit
> 0040 10 p/s 1 kb/s 16 kbit
> 0041 3160 p/s 580 kb/s 4752 kbit
> 0044 156 p/s 28 kb/s 234 kbit
> 1ffb 39 p/s 7 kb/s 59 kbit
> 1fff 939 p/s 172 kb/s 1413 kbit
> 2000 12901 p/s 2368 kb/s 19403 kbit
>
> So I know that KGO is coming fine in pid pairs of 31,34 and 41,44.
> Then I added the following two lines in channels.conf file
>
> TEST:533000000:8VSB:49:52
> T2:533000000:8VSB:65:68
>
> And ran the following commands
>
> root at mythtvbe:/tftpboot# azap -r TEST
> using '/dev/dvb/adapter0/frontend0' and '/dev/dvb/adapter0/demux0'
> tuning to 533000000 Hz
> video pid 0x0031, audio pid 0x0034
> status 1f | signal da5d | snr f9ef | ber 00000000 | unc 00000000 | FE_HAS_LOCK
> status 1f | signal dcab | snr fa43 | ber 00000000 | unc 00000000 | FE_HAS_LOCK
> status 1f | signal dcab | snr fa31 | ber 00000000 | unc 00000000 | FE_HAS_LOCK
> status 1f | signal da5d | snr fa1d | ber 00000000 | unc 00000000 | FE_HAS_LOCK
> status 1f | signal d80f | snr f9e7 | ber 00000000 | unc 00000000 | FE_HAS_LOCK
> status 1f | signal da5d | snr f9e5 | ber 00000000 | unc 00000000 | FE_HAS_LOCK
> status 1f | signal da5d | snr f9d9 | ber 00000000 | unc 00000000 | FE_HAS_LOCK
> status 1f | signal d80f | snr fa15 | ber 00000000 | unc 00000000 | FE_HAS_LOCK
>
> root at mythtvbe:/tftpboot# azap -r T2
> using '/dev/dvb/adapter0/frontend0' and '/dev/dvb/adapter0/demux0'
> tuning to 533000000 Hz
> video pid 0x0041, audio pid 0x0044
> status 1f | signal da5d | snr fa1f | ber 00000000 | unc 00000000 | FE_HAS_LOCK
> status 1f | signal d80f | snr f9df | ber 00000000 | unc 00000000 | FE_HAS_LOCK
> status 1f | signal da5d | snr fa13 | ber 00000000 | unc 00000000 | FE_HAS_LOCK
> status 1f | signal da5d | snr fa07 | ber 00000000 | unc 00000000 | FE_HAS_LOCK
> status 1f | signal d80f | snr f9e3 | ber 00000000 | unc 00000000 | FE_HAS_LOCK
> status 1f | signal d80f | snr f9b7 | ber 00000000 | unc 00000000 | FE_HAS_LOCK
> status 1f | signal dcab | snr fa15 | ber 00000000 | unc 00000000 | FE_HAS_LOCK
>
> But when I goto mythtv-setup->Channel Editor, the pids are (0)(0) for
> both 7_1 and 7_2. I think thats the reason I can't watch either of 7_1
> or 7_2 correctly. Does anyone knows how can I fix the pids ? I tried
> Advanced option, but there is no place where I can put the pids in
> there.
>
> I've similar issue with channel 36 (KICU). I cant record it. Same
> error messages. Even though azap can lock it fine and dvbtraffic
> reports valid pids.
>
> root at mythtvbe:/tftpboot# azap -r KICU
> using '/dev/dvb/adapter0/frontend0' and '/dev/dvb/adapter0/demux0'
> tuning to 701000000 Hz
> video pid 0x0000, audio pid 0x0000
> status 1f | signal c624 | snr f7e3 | ber 00000000 | unc 00000000 | FE_HAS_LOCK
> status 1f | signal c7ee | snr f837 | ber 00000000 | unc 00000000 | FE_HAS_LOCK
> status 1f | signal c624 | snr f815 | ber 00000000 | unc 00000000 | FE_HAS_LOCK
> status 1f | signal c459 | snr f81f | ber 00000000 | unc 00000000 | FE_HAS_LOCK
> status 1f | signal c624 | snr f871 | ber 00000000 | unc 00000000 | FE_HAS_LOCK
> status 1f | signal c624 | snr f835 | ber 00000000 | unc 00000000 | FE_HAS_LOCK
>
> -PID--FREQ-----BANDWIDTH-BANDWIDTH-
> 0000 9 p/s 1 kb/s 14 kbit
> 0030 9 p/s 1 kb/s 14 kbit
> 0031 9770 p/s 1793 kb/s 14695 kbit
> 0034 156 p/s 28 kb/s 234 kbit
> 1d00 5 p/s 0 kb/s 8 kbit
> 1e00 6 p/s 1 kb/s 10 kbit
> 1e80 0 p/s 0 kb/s 1 kbit
> 1ffb 40 p/s 7 kb/s 60 kbit
> 1fff 2900 p/s 532 kb/s 4361 kbit
> 2000 12901 p/s 2368 kb/s 19403 kbit
> -PID--FREQ-----BANDWIDTH-BANDWIDTH-
>
> Thanks in advance !
>
> Mudit
>
More information about the mythtv-users
mailing list