[mythtv-users] PVR-150 (Model 1045) - $64.99 @ CompUSA + FAQ
jay-lists at 3pound.com
Sun Sep 11 23:17:21 UTC 2005
On Sun, 11 Sep 2005 14:59:16 -0700
Mark Menke <mmenke at porksoda.com> wrote:
> Do you have to passs any special flags to the ivtv module when you
> load it? I 've got the same card, but can't get the audio to work.
> cat/dev/video0 leaves my with an mpg that has great video and no
FYI regarding thread subject - deal is expired, back to $99.
No sir, nothing special, and my cat /dev/video0 test came with crystal
clear audio and CPU only spiked briefly (to ~20%) at startup, then
back to about 3-5% .. which is normal.
I spose I should point out, I captured DVD output using composite
cables (which was on Composite 1: ivtvctl -p 3). I don't recall having
to manually set a corresponding audio input.
I used the firmware from the included CD, and had to tweak
ivtvfwextract.pl to do so. I may heed the warning of it's being
"buggy!!!" and use one from the ivtv site.
Since my shiny new PVR-150 will live under the staircase, I had to
build a serial IR receiver in the time since I last replied here (to
my amazement, it works!).
Point being - I'm probably the _least_ qualified to debug this issue,
but I've included my relevant dmesg output. (You may wanna take this
to the ivtv list)
Having said that - how are you determining the audio is missing?
Also, according to dmesg, do you see 'tveeprom: audio processor =
CX25841 (type = 23)' or similar?
How about 'ivtv: Create DMA encoder PCM audio stream: 0 x 4608 buffers
Any error messages?
If not, maybe it's as simple as using ivtvctl to get the proper
ivtv: ==================== START INIT IVTV ====================
ivtv: version 0.3.8 (svn snapshot revision 2638) loading
ivtv: Linux version: 2.6.10-5-k7 preempt K7 gcc-3.3
ivtv: In case of problems please include the debug info
ivtv: between the START INIT IVTV and END INIT IVTV lines when
ivtv: mailing the ivtv-devel mailinglist.
ivtv: Autodetected WinTV PVR 150 card (iTVC16 based)
ACPI: PCI interrupt 0000:00:0a.0[A] -> GSI 14 (level, low) -> IRQ 14
lirc_i2c: chip found @ 0x71 (Hauppauge IR (PVR150))
ivtv: i2c attach to card #0 ok [client=Hauppauge IR (PVR150), addr=71]
lirc_dev: lirc_register_plugin: sample_rate: 10
tveeprom: Hauppauge: model = 26032, rev = C199, serial# = 0123456
tveeprom: tuner = TCL 2002N 5H (idx = 99, type = 50)
tveeprom: tuner fmt = NTSC(M) (eeprom = 0x08, v4l2 = 0x00001000)
tveeprom: audio processor = CX25841 (type = 23)
tveeprom: decoder processor = CX25841 (type = 1c)
ivtv: i2c attach to card #0 ok [client=tveeprom, addr=50]
tuner: chip found at addr 0xc2 i2c-bus ivtv i2c driver #0
ivtv: i2c attach to card #0 ok [client=(tuner unset), addr=61]
cx25840: loading /lib/modules/HcwMakoA.ROM
ivtv: i2c attach to card #0 ok [client=cx25840, addr=44]
ivtv: i2c attach to card #0 ok [client=wm8775, addr=1b]
ivtv: loading /lib/modules/ivtv-fw-enc.bin
ivtv: Encoder revision: 0x02050032
ivtv warning: Encoder Firmware can be buggy, use version
ivtv: Create DMA encoder MPEG stream: 0 x 32768 buffers (0KB total)
ivtv: Create DMA encoder YUV stream: 0 x 10800 buffers (0KB total)
ivtv: Create DMA encoder VBI stream: 0 x 17472 buffers (0KB total)
ivtv: Create DMA encoder PCM audio stream: 0 x 4608 buffers (0KB
tuner: type set to 50 (TCL 2002N) by ivtv i2c driver #0
ivtv: Initialized WinTV PVR 150, card #0
ivtv: ==================== END INIT IVTV ====================
More information about the mythtv-users