[mythtv-users] Sound w/PVR500, no sound w/PVR250
Matt
skd5aner at gmail.com
Mon Jul 3 23:06:49 UTC 2006
Hello,
I recently upgraded my ubuntu distro to 6.06 (2.6.15 kernel).
Afterwards, I upgraded my IVTV to 0.4.6. After the install, I can get
sound and picture to work just fine with my PVR-500, but I only get a
picture (no audio) with my PVR 250s. I can't figure out what's wrong,
and I've been struggling with this for several hours now. Any advice?
Here's my dmesg output:
[4294679.537000] ivtv: ==================== START INIT IVTV
====================
[4294679.537000] ivtv: version 0.4.6 (tagged release) loading
[4294679.537000] ivtv: Linux version: 2.6.15-23-386 preempt 486 gcc-4.0
[4294679.537000] ivtv: In case of problems please include the debug
info between
[4294679.537000] ivtv: the START INIT IVTV and END INIT IVTV lines, along with
[4294679.537000] ivtv: any module options, when mailing the
ivtv-users mailinglist.
[4294679.537000] ivtv0: Autodetected WinTV PVR 250 card (cx23416 based)
[4294679.538000] **** SET: Misaligned resource pointer: de27ccc2 Type 07 Len 0
[4294679.538000] ACPI: PCI Interrupt Link [LNK1] enabled at IRQ 11
[4294679.538000] ACPI: PCI Interrupt 0000:01:08.0[A] -> Link [LNK1] ->
GSI 11 (level, low) -> IRQ 11
[4294679.538000] ivtv0: Unreasonably low latency timer, setting to 64 (was 32)
[4294679.646000] nvidia: module license 'NVIDIA' taints kernel.
[4294679.661000] eth0: no link during initialization.
[4294679.715000] tveeprom: ivtv version
[4294679.715000] tveeprom: Hauppauge: model = 32032, rev = B326,
serial# = 7108953
[4294679.715000] tveeprom: tuner = Temic 4036FY5 (idx = 26, type = 8)
[4294679.715000] tveeprom: tuner fmt = NTSC(M) (eeprom = 0x08, v4l2 =
0x00001000)
[4294679.715000] tveeprom: audio processor = MSP4448 (type = 1b)
[4294679.715000] tveeprom: decoder processor = SAA7115 (type = 13)
[4294679.715000] ivtv0: i2c attach to card #0 ok [client=tveeprom, addr=50]
[4294679.724000] ts: Compaq touchscreen protocol output
[4294679.746000] tuner (ivtv): chip found at addr 0xc2 i2c-bus ivtv
i2c driver #0
[4294679.746000] ivtv0: i2c attach to card #0 ok [client=(tuner unset), addr=61]
[4294679.976000] saa7115 2-0021: saa7115 found @ 0x42 (ivtv i2c driver #0)
[4294680.031000] eth0: link up.
[4294680.133000] ivtv0: i2c attach to card #0 ok [client=saa7115, addr=21]
[4294680.170000] ivtv0: Failed to load module msp3400
[4294680.685000] NET: Registered protocol family 17
[4294680.769000] smbfs: mount_data version 1919251317 is not supported
[4294680.931000] ivtv0: loaded v4l-cx2341x-enc.fw firmware (262144 bytes)
[4294681.151000] ivtv0: Encoder revision: 0x02050032
[4294681.151000] ivtv0: Allocate DMA encoder MPEG stream: 128 x 32768
buffers (4096KB total)
[4294681.151000] ivtv0: Allocate DMA encoder YUV stream: 194 x 10800
buffers (2048KB total)
[4294681.151000] ivtv0: Allocate DMA encoder VBI stream: 120 x 17472
buffers (2048KB total)
[4294681.151000] ivtv0: Allocate DMA encoder PCM audio stream: 455 x
4608 buffers (2048KB total)
[4294681.152000] tuner: type set to 8 (Temic NTSC (4036 FY5)) by ivtv
i2c driver #0
[4294681.199000] ivtv0 warning: i2c client addr: 0x40 not found for
command 0x40086d11!
[4294681.199000] ivtv0 warning: i2c client addr: 0x40 not found for
command 0x80287610!
[4294681.199000] ivtv0 warning: i2c client addr: 0x40 not found for
command 0x40287611!
[4294681.199000] ivtv0 warning: i2c client addr: 0x40 not found for
command 0x40085618!
[4294681.242000] ivtv0 warning: i2c client addr: 0x40 not found for
command 0x80287610!
[4294681.242000] ivtv0 warning: i2c client addr: 0x40 not found for
command 0x40287611!
[4294681.243000] ivtv0 warning: i2c client addr: 0x40 not found for
command 0x402c5639!
[4294681.243000] ivtv0 warning: i2c client addr: 0x40 not found for
command 0x80287610!
[4294681.243000] ivtv0 warning: i2c client addr: 0x40 not found for
command 0x40287611!
[4294681.243000] ivtv0: Initialized WinTV PVR 250, card #0
[4294681.243000] **** SET: Misaligned resource pointer: de62e5e2 Type 07 Len 0
[4294681.243000] ACPI: PCI Interrupt Link [LNK4] enabled at IRQ 10
[4294681.243000] ACPI: PCI Interrupt 0000:03:00.0[A] -> Link [LNK4] ->
GSI 10 (level, low) -> IRQ 10
[4294681.244000] NVRM: loading NVIDIA Linux x86 Kernel Module
1.0-8756 Wed Mar 29 14:26:26 PST 2006
[4294681.495000] ivtv: ====================== NEXT CARD
======================
[4294681.495000] ivtv1: Autodetected WinTV PVR 250 card (cx23416 based)
[4294681.495000] **** SET: Misaligned resource pointer: ddca5d22 Type 07 Len 0
[4294681.496000] ACPI: PCI Interrupt Link [LNK3] enabled at IRQ 5
[4294681.496000] ACPI: PCI Interrupt 0000:01:0a.0[A] -> Link [LNK3] ->
GSI 5 (level, low) -> IRQ 5
[4294681.496000] ivtv1: Unreasonably low latency timer, setting to 64 (was 32)
[4294681.548000] tveeprom: ivtv version
[4294681.548000] tveeprom: Hauppauge: model = 32032, rev = B326,
serial# = 7109851
[4294681.548000] tveeprom: tuner = Temic 4036FY5 (idx = 26, type = 8)
[4294681.548000] tveeprom: tuner fmt = NTSC(M) (eeprom = 0x08, v4l2 =
0x00001000)
[4294681.548000] tveeprom: audio processor = MSP4448 (type = 1b)
[4294681.548000] tveeprom: decoder processor = SAA7115 (type = 13)
[4294681.548000] ivtv1: i2c attach to card #1 ok [client=tveeprom, addr=50]
[4294681.563000] tuner (ivtv): chip found at addr 0xc2 i2c-bus ivtv
i2c driver #1
[4294681.563000] ivtv1: i2c attach to card #1 ok [client=(tuner unset), addr=61]
[4294681.757000] saa7115 3-0021: saa7115 found @ 0x42 (ivtv i2c driver #1)
[4294681.916000] ivtv1: i2c attach to card #1 ok [client=saa7115, addr=21]
[4294682.007000] ivtv1: Failed to load module msp3400
[4294682.658000] ivtv1: loaded v4l-cx2341x-enc.fw firmware (262144 bytes)
[4294682.878000] ivtv1: Encoder revision: 0x02050032
[4294682.878000] ivtv1: Allocate DMA encoder MPEG stream: 128 x 32768
buffers (4096KB total)
[4294682.878000] ivtv1: Allocate DMA encoder YUV stream: 194 x 10800
buffers (2048KB total)
[4294682.878000] ivtv1: Allocate DMA encoder VBI stream: 120 x 17472
buffers (2048KB total)
[4294682.878000] ivtv1: Allocate DMA encoder PCM audio stream: 455 x
4608 buffers (2048KB total)
[4294682.879000] tuner: type set to 8 (Temic NTSC (4036 FY5)) by ivtv
i2c driver #1
[4294682.925000] ivtv1 warning: i2c client addr: 0x40 not found for
command 0x40086d11!
[4294682.925000] ivtv1 warning: i2c client addr: 0x40 not found for
command 0x80287610!
[4294682.925000] ivtv1 warning: i2c client addr: 0x40 not found for
command 0x40287611!
[4294682.925000] ivtv1 warning: i2c client addr: 0x40 not found for
command 0x40085618!
[4294682.968000] ivtv1 warning: i2c client addr: 0x40 not found for
command 0x80287610!
[4294682.968000] ivtv1 warning: i2c client addr: 0x40 not found for
command 0x40287611!
[4294682.969000] ivtv1 warning: i2c client addr: 0x40 not found for
command 0x402c5639!
[4294682.969000] ivtv1 warning: i2c client addr: 0x40 not found for
command 0x80287610!
[4294682.969000] ivtv1 warning: i2c client addr: 0x40 not found for
command 0x40287611!
[4294682.969000] ivtv1: Initialized WinTV PVR 250, card #1
[4294682.969000] ivtv: ====================== NEXT CARD
======================
[4294682.969000] ivtv2: Autodetected WinTV PVR 150 card (cx23416 based)
[4294682.969000] ACPI: PCI Interrupt 0000:02:08.0[A] -> Link [LNK3] ->
GSI 5 (level, low) -> IRQ 5
[4294682.969000] ivtv2: Unreasonably low latency timer, setting to 64 (was 32)
[4294683.026000] tveeprom: Second (radio) tuner idx 101
[4294683.026000] tveeprom: ivtv version
[4294683.026000] tveeprom: Hauppauge: model = 23552, rev = D492,
serial# = 7893589
[4294683.026000] tveeprom: tuner = Philips FQ1236A MK4 (idx = 92, type = 57)
[4294683.026000] tveeprom: tuner fmt = NTSC(M) (eeprom = 0x08, v4l2 =
0x00001000)
[4294683.026000] tveeprom: audio processor = CX25843 (type = 25)
[4294683.026000] tveeprom: decoder processor = CX25843 (type = 1e)
[4294683.026000] ivtv2: i2c attach to card #2 ok [client=tveeprom, addr=50]
[4294683.027000] tuner (ivtv): chip found at addr 0xc0 i2c-bus ivtv
i2c driver #2
[4294683.028000] TEA5767 detected.
[4294683.028000] ivtv2: i2c attach to card #2 ok [client=(tuner unset), addr=60]
[4294683.028000] tuner: type set to 62 (Philips TEA5767HN FM Radio) by
autodetect
[4294683.028000] type set to 62 (Philips TEA5767HN FM Radio)
[4294683.029000] tuner (ivtv): chip found at addr 0xc2 i2c-bus ivtv
i2c driver #2
[4294683.029000] ivtv2: i2c attach to card #2 ok [client=(tuner unset), addr=61]
[4294683.280000] tda9887 4-0043: (ivtv) chip found @ 0x86 (ivtv i2c driver #2)
[4294683.280000] ivtv2: i2c attach to card #2 ok [client=tda9887, addr=43]
[4294683.299000] ivtv2: This is the first unit of a PVR500
[4294683.343000] cx25840 4-0044: ivtv driver
[4294683.343000] cx25840 4-0044: cx25843-23 found @ 0x88 (ivtv i2c driver #2)
[4294683.551000] Vendor: AFT PRO Model: - 9 CF Rev: 0822
[4294683.551000] Type: Direct-Access ANSI
SCSI revision: 00
[4294683.553000] Vendor: AFT PRO Model: - 9 SD Rev: 0822
[4294683.553000] Type: Direct-Access ANSI
SCSI revision: 00
[4294683.554000] Vendor: AFT PRO Model: - 9 SM/XD Rev: 0822
[4294683.554000] Type: Direct-Access ANSI
SCSI revision: 00
[4294683.555000] Vendor: AFT PRO Model: - 9 MS Rev: 0822
[4294683.555000] Type: Direct-Access ANSI
SCSI revision: 00
[4294683.559000] usb-storage: device scan complete
[4294683.571000] Driver 'sd' needs updating - please use bus_type methods
[4294683.576000] sd 0:0:0:0: Attached scsi removable disk sda
[4294683.581000] sd 0:0:0:1: Attached scsi removable disk sdb
[4294683.586000] sd 0:0:0:2: Attached scsi removable disk sdc
[4294683.591000] sd 0:0:0:3: Attached scsi removable disk sdd
[4294683.599000] sd 0:0:0:0: Attached scsi generic sg0 type 0
[4294683.599000] sd 0:0:0:1: Attached scsi generic sg1 type 0
[4294683.600000] sd 0:0:0:2: Attached scsi generic sg2 type 0
[4294683.600000] sd 0:0:0:3: Attached scsi generic sg3 type 0
[4294687.994000] cx25840 4-0044: loaded v4l-cx25840.fw firmware (16382 bytes)
[4294688.081000] ivtv2: i2c attach to card #2 ok [client=cx25840, addr=44]
[4294688.151000] wm8775 4-001b: chip found @ 0x36 (ivtv i2c driver #2)
[4294688.162000] ivtv2: i2c attach to card #2 ok [client=wm8775, addr=1b]
[4294688.165000] ivtv2: Detected a TEA5767 radio tuner. Enabling radio support.
[4294688.815000] ivtv2: loaded v4l-cx2341x-enc.fw firmware (262144 bytes)
[4294689.035000] ivtv2: Encoder revision: 0x02050032
[4294689.035000] ivtv2: Allocate DMA encoder MPEG stream: 128 x 32768
buffers (4096KB total)
[4294689.035000] ivtv2: Allocate DMA encoder YUV stream: 194 x 10800
buffers (2048KB total)
[4294689.035000] ivtv2: Allocate DMA encoder VBI stream: 120 x 17472
buffers (2048KB total)
[4294689.035000] ivtv2: Allocate DMA encoder PCM audio stream: 455 x
4608 buffers (2048KB total)
[4294689.037000] ivtv2: Create encoder radio stream
[4294689.037000] tuner: type set to 57 (Philips FQ1236A MK4) by ivtv
i2c driver #2
[4294689.158000] ivtv2: Initialized WinTV PVR 500 (unit #1), card #2
[4294689.158000] ivtv: ====================== NEXT CARD
======================
[4294689.158000] ivtv3: Autodetected WinTV PVR 150 card (cx23416 based)
[4294689.158000] ACPI: PCI Interrupt 0000:02:09.0[A] -> Link [LNK4] ->
GSI 10 (level, low) -> IRQ 10
[4294689.158000] ivtv3: Unreasonably low latency timer, setting to 64 (was 32)
[4294689.214000] tveeprom: Second (radio) tuner idx 101
[4294689.214000] tveeprom: ivtv version
[4294689.214000] tveeprom: Hauppauge: model = 23552, rev = D492,
serial# = 7893589
[4294689.214000] tveeprom: tuner = Philips FQ1236A MK4 (idx = 92, type = 57)
[4294689.214000] tveeprom: tuner fmt = NTSC(M) (eeprom = 0x08, v4l2 =
0x00001000)
[4294689.214000] tveeprom: audio processor = CX25843 (type = 25)
[4294689.214000] tveeprom: decoder processor = CX25843 (type = 1e)
[4294689.214000] ivtv3: i2c attach to card #3 ok [client=tveeprom, addr=50]
[4294689.229000] tuner (ivtv): chip found at addr 0xc2 i2c-bus ivtv
i2c driver #3
[4294689.229000] ivtv3: i2c attach to card #3 ok [client=(tuner unset), addr=61]
[4294689.481000] tda9887 5-0043: (ivtv) chip found @ 0x86 (ivtv i2c driver #3)
[4294689.481000] ivtv3: i2c attach to card #3 ok [client=tda9887, addr=43]
[4294689.504000] cx25840 5-0044: ivtv driver
[4294689.504000] cx25840 5-0044: cx25843-23 found @ 0x88 (ivtv i2c driver #3)
[4294693.929000] cx25840 5-0044: loaded v4l-cx25840.fw firmware (16382 bytes)
[4294694.016000] ivtv3: i2c attach to card #3 ok [client=cx25840, addr=44]
[4294694.016000] wm8775 5-001b: chip found @ 0x36 (ivtv i2c driver #3)
[4294694.027000] ivtv3: i2c attach to card #3 ok [client=wm8775, addr=1b]
[4294694.030000] ivtv3: This is the second unit of a PVR500
[4294694.030000] ivtv3: Correcting tveeprom data: no radio present on
second unit
[4294694.718000] ivtv3: loaded v4l-cx2341x-enc.fw firmware (262144 bytes)
[4294694.938000] ivtv3: Encoder revision: 0x02050032
[4294694.938000] ivtv3: Allocate DMA encoder MPEG stream: 128 x 32768
buffers (4096KB total)
[4294694.938000] ivtv3: Allocate DMA encoder YUV stream: 194 x 10800
buffers (2048KB total)
[4294694.938000] ivtv3: Allocate DMA encoder VBI stream: 120 x 17472
buffers (2048KB total)
[4294694.938000] ivtv3: Allocate DMA encoder PCM audio stream: 455 x
4608 buffers (2048KB total)
[4294694.939000] tuner: type set to 57 (Philips FQ1236A MK4) by ivtv
i2c driver #3
[4294695.060000] ivtv3: Initialized WinTV PVR 500 (unit #2), card #3
[4294695.060000] ivtv: ==================== END INIT IVTV
====================
[4294745.832000] ivtv0 warning: i2c client addr: 0x40 not found for
command 0x80287610!
[4294745.832000] ivtv0 warning: i2c client addr: 0x40 not found for
command 0x40287611!
[4294745.833000] ivtv0 warning: i2c client addr: 0x40 not found for
command 0x402c5639!
[4294745.833000] ivtv0 warning: i2c client addr: 0x40 not found for
command 0x80287610!
[4294745.833000] ivtv0 warning: i2c client addr: 0x40 not found for
command 0x40287611!
[4294745.858000] ivtv1 warning: i2c client addr: 0x40 not found for
command 0x80287610!
[4294745.858000] ivtv1 warning: i2c client addr: 0x40 not found for
command 0x40287611!
[4294745.860000] ivtv1 warning: i2c client addr: 0x40 not found for
command 0x402c5639!
[4294745.860000] ivtv1 warning: i2c client addr: 0x40 not found for
command 0x80287610!
[4294745.860000] ivtv1 warning: i2c client addr: 0x40 not found for
command 0x40287611!
More information about the mythtv-users
mailing list