[mythtv-users] Cant get X to work with FC5, Mythtv .19 and PVR-350
Kenneth G Eitenmiller Jr
kge2 at eitenmiller.net
Fri Jun 9 19:09:06 UTC 2006
This is my second MythTV box. I blew up the first one, filled the hard drives, but it ran flawlessly for months.
I am trying to install MythTV (.19) on FC5 and am stuck at the "Running X on the PVR-350's TV-Out" in Jarod's HOWTO. I am also using references from the Wiki. When it comes to killing X and starting with the new xorg.conf file, it "can't start X". It never goes to the tv. Below is my xorg.conf file that I am using with an lspci of 01:07.0 and fb1. As a note, I could not make cat /var/log/messages |grep "iTVC15 TV out" but found it using "TV out".
Where did I screw up my xorg.conf?
Any ideas?
Thanks,
Ken
# Xorg configuration created by system-config-display
Section "ServerLayout"
Identifier "single head configuration"
Screen 0 "Screen0" 0 0
InputDevice "Mouse0" "CorePointer"
InputDevice "Keyboard0" "CoreKeyboard"
EndSection
Section "Files"
# Multiple FontPath entries are allowed (they are concatenated together)
# By default, a font server independent of the X server is
# used to render fonts.
FontPath "unix/:7100"
EndSection
Section "Module"
Load "dbe"
Load "extmod"
Load "fbdevhw"
Load "glx"
Load "record"
Load "freetype"
Load "type1"
Load "dri"
EndSection
Section "InputDevice"
# Specify which keyboard LEDs can be user-controlled (eg, with xset(1))
# Option "Xleds" "1 2 3"
# To disable the XKEYBOARD extension, uncomment XkbDisable.
# Option "XkbDisable"
# To customise the XKB settings to suit your keyboard, modify the
# lines below (which are the defaults). For example, for a non-U.S.
# keyboard, you will probably want to use:
# Option "XkbModel" "pc102"
# If you have a US Microsoft Natural keyboard, you can use:
# Option "XkbModel" "microsoft"
#
# Then to change the language, change the Layout setting.
# For example, a german layout can be obtained with:
# Option "XkbLayout" "de"
# or:
# Option "XkbLayout" "de"
# Option "XkbVariant" "nodeadkeys"
#
# If you'd like to switch the positions of your capslock and
# control keys, use:
# Option "XkbOptions" "ctrl:swapcaps"
# Or if you just want both to be control, use:
# Option "XkbOptions" "ctrl:nocaps"
#
Identifier "Keyboard0"
Driver "kbd"
Option "XkbModel" "pc105"
Option "XkbLayout" "us"
EndSection
Section "InputDevice"
Identifier "Mouse0"
Driver "mouse"
Option "Protocol" "IMPS/2"
Option "Device" "/dev/input/mice"
Option "ZAxisMapping" "4 5"
Option "Emulate3Buttons" "yes"
EndSection
Section "Monitor"
Identifier "NTSC Monitor"
HorizSync 30-68
VertRefresh 50-120
DisplaySize 183 122
Mode "720x480"
# D: 34.563 MHz, H: 37.244 kHz. V: 73.897 Hz
DotClock 34.564
HTimings 720 752 840 928
VTimings 480 484 488 504
Flags "-HSync" "-VSync"
EndMode
EndSection
###Section "Monitor"
### Identifier "Monitor0"
### VendorName "Monitor Vendor"
### ModelName "Dell 1905FP (Analog)"
### DisplaySize 380 310
### ### Comment all HorizSync and VertSync values to use DDC:
### HorizSync 30.0 - 81.0
### VertRefresh 56.0 - 76.0
### Option "dpms"
###EndSection
Section "Device"
Identifier "Hauppauge PVR 350 iTVC15 Framebuffer"
Driver "ivtvdev"
Option "ivtv0" "/dev/fb1"
Option "VideoOverlay" "on"
Option "XVideo" "1"
BusID "PCI:1:7:0"
Screen 0
EndSection
###Section "Device"
### Identifier "Videocard0"
### Driver "nv"
### VendorName "Videocard vendor"
### BoardName "nVidia Corporation NV18 [GeForce4 MX 4000 AGP 8x]"
###EndSection
Section "Screen"
Identifier "Screen0"
Device "Hauppauge PVR 350 iTVC15 Framebuffer"
Monitor "NTSC Monitor"
DefaultDepth 24
DefaultFbbpp 32
Subsection "Display"
Depth 24
FbBpp 32
Modes "720x480"
EndSubsection
EndSection
###Section "Screen"
### Identifier "Screen0"
### Device "Videocard0"
### Monitor "Monitor0"
### DefaultDepth 24
### SubSection "Display"
### Viewport 0 0
### Depth 16
### Modes "800x600" "640x480"
### EndSubSection
### SubSection "Display"
### Viewport 0 0
### Depth 24
### Modes "1280x1024"
### EndSubSection
###EndSection
Section "DRI"
Group 0
Mode 0666
EndSection
More information about the mythtv-users
mailing list