[mythtv-users] [k]radio using ivtv 6.2.2-2 and Hauppauge PVR350

Wed Jun 28 18:16:58 UTC 2006

I posted the below to the ivtv list but received no response.
Does anyone on this list know the answer or know where best to ask this question?

--------------------------------------------------------------

I have a system with a Hauppauge PVR350 and PVR250 installed.

I have been unable to get kradio (or other radio app like xmms-fmradio)
to work.

$ ivtv-radio -f 91.5

works fine so I think I have the drives installed and loading ok.

Is there some trick to getting this configured?

Am I missing a piece here?

Thanks
R.Parr, RHCE, Temporal Arts

$ dmesg | tac |

>> sed -n '/=\ \ END INIT IVTV\ \ =/,/= START INIT IVTV =/p;
>>     /= START INIT IVTV =/q' |
>> tac
>  
>
ivtv:  ==================== START INIT IVTV ====================
ivtv:  version 0.6.2 (tagged release) loading
ivtv:  Linux version: 2.6.16-2-amd64-k8 gcc-4.0
ivtv:  In case of problems please include the debug info between
ivtv:  the START INIT IVTV and END INIT IVTV lines, along with
ivtv:  any module options, when mailing the ivtv-users mailinglist.
eth0: forcedeth.c: subsystem: 015d9:1011 bound to 0000:00:0a.0
ACPI: PCI Interrupt Link [LK2N] enabled at IRQ 45
GSI 21 sharing vector 0x42 and IRQ 21
ACPI: PCI Interrupt 0000:80:0a.0[A] -> Link [LK2N] -> GSI 45 (level,
low) -> IRQ 66
PCI: Setting latency timer of device 0000:80:0a.0 to 64
ACPI: PCI Interrupt Link [LNKA] enabled at IRQ 19
GSI 22 sharing vector 0x4A and IRQ 22
ACPI: PCI Interrupt 0000:05:02.2[B] -> Link [LNKA] -> GSI 19 (level,
low) -> IRQ 74
ohci1394: fw-host0: OHCI-1394 1.1 (PCI): IRQ=[74]
MMIO=[afbff800-afbfffff]  Max Packet=[2048]  IR/IT contexts=[4/8]
i2c_adapter i2c-0: nForce2 SMBus adapter at 0x4c00
i2c_adapter i2c-1: nForce2 SMBus adapter at 0x4c40
gameport: EMU10K1 is pci0000:05:02.1/gameport0, io 0x9c00, speed 1206kHz
ivtv0: Autodetected Hauppauge WinTV PVR-150 card (cx23416 based)
ACPI: PCI Interrupt Link [LNKC] enabled at IRQ 18
GSI 23 sharing vector 0x52 and IRQ 23
ACPI: PCI Interrupt 0000:06:08.0[A] -> Link [LNKC] -> GSI 18 (level,
low) -> IRQ 82
tveeprom 2-0050: Hauppauge model 23552, rev D492, serial# 7894525
tveeprom 2-0050: tuner model is Philips FQ1236A MK4 (idx 92, type 57)
tveeprom 2-0050: TV standards NTSC(M) (eeprom 0x08)
tveeprom 2-0050: second tuner model is Philips TEA5768HL FM Radio (idx
101, type 62)
tveeprom 2-0050: audio processor is CX25843 (idx 37)
tveeprom 2-0050: decoder processor is CX25843 (idx 30)
tveeprom 2-0050: has radio, has no IR remote
ivtv0: This is the first unit of a PVR500
input: ImExPS/2 Generic Explorer Mouse as /class/input/input1
input: PC Speaker as /class/input/input2
tuner 2-0060: TEA5767 detected.
tuner 2-0060: chip found @ 0xc0 (ivtv i2c driver #0)
tuner 2-0060: type set to 62 (Philips TEA5767HN FM Radio)
tuner 2-0061: chip found @ 0xc2 (ivtv i2c driver #0)
ACPI: PCI Interrupt Link [LUS2] enabled at IRQ 22
ACPI: PCI Interrupt 0000:00:02.1[B] -> Link [LUS2] -> GSI 22 (level,
low) -> IRQ 217
PCI: Setting latency timer of device 0000:00:02.1 to 64
ehci_hcd 0000:00:02.1: EHCI Host Controller
ehci_hcd 0000:00:02.1: debug port 1
PCI: cache line size of 64 is not supported by device 0000:00:02.1
ehci_hcd 0000:00:02.1: new USB bus registered, assigned bus number 1
ehci_hcd 0000:00:02.1: irq 217, io mem 0xafce0000
ehci_hcd 0000:00:02.1: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 10 ports detected
ohci_hcd: 2005 April 22 USB 1.1 'Open' Host Controller (OHCI) Driver (PCI)
pci_hotplug: PCI Hot Plug PCI Core version: 0.5
ACPI: PCI Interrupt Link [LUS0] enabled at IRQ 21
ACPI: PCI Interrupt 0000:00:02.0[A] -> Link [LUS0] -> GSI 21 (level,
low) -> IRQ 225
PCI: Setting latency timer of device 0000:00:02.0 to 64
ohci_hcd 0000:00:02.0: OHCI Host Controller
ohci_hcd 0000:00:02.0: new USB bus registered, assigned bus number 2
ohci_hcd 0000:00:02.0: irq 225, io mem 0xafcfc000
tda9887 2-0043: chip found @ 0x86 (ivtv i2c driver #0)
usb usb2: configuration #1 chosen from 1 choice
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 10 ports detected
cx25840 2-0044: cx25843-23 found @ 0x88 (ivtv i2c driver #0)
eth1: forcedeth.c: subsystem: 015d9:1011 bound to 0000:80:0a.0
usb 1-3: new high speed USB device using ehci_hcd and address 2
usb 1-3: configuration #1 chosen from 1 choice
hub 1-3:1.0: USB hub found
hub 1-3:1.0: 3 ports detected
cx25840 2-0044: loaded v4l-cx25840.fw firmware (14264 bytes)
wm8775 2-001b: chip found @ 0x36 (ivtv i2c driver #0)
usb 1-3.1: new high speed USB device using ehci_hcd and address 3
usb 1-3.1: configuration #1 chosen from 1 choice
hub 1-3.1:1.0: USB hub found
hub 1-3.1:1.0: 3 ports detected
ieee1394: Host added: ID:BUS[0-00:1023]  GUID[00023c0151113a32]
eth1394: eth2: IEEE-1394 IPv4 over 1394 Ethernet (fw-host0)
usb 1-3.1.1: new high speed USB device using ehci_hcd and address 4
usb 1-3.1.1: configuration #1 chosen from 1 choice
ivtv0: loaded v4l-cx2341x-enc.fw firmware (262144 bytes)
ivtv0: Encoder revision: 0x02050032
ivtv0: Allocate DMA encoder MPEG stream: 128 x 32768 buffers (4096KB total)
ivtv0: Allocate DMA encoder YUV stream: 194 x 10800 buffers (2048KB total)
ivtv0: Allocate DMA encoder VBI stream: 120 x 17472 buffers (2048KB total)
ivtv0: Allocate DMA encoder PCM audio stream: 455 x 4608 buffers (2048KB
total)
ivtv0: Create encoder radio stream
tuner 2-0061: type set to 57 (Philips FQ1236A MK4)
ivtv0: Initialized WinTV PVR 500 (unit #1), card #0
ivtv:  ======================  NEXT CARD  ======================
ivtv1: Autodetected Hauppauge WinTV PVR-150 card (cx23416 based)
ACPI: PCI Interrupt Link [LNKD] enabled at IRQ 17
GSI 24 sharing vector 0x5A and IRQ 24
ACPI: PCI Interrupt 0000:06:09.0[A] -> Link [LNKD] -> GSI 17 (level,
low) -> IRQ 90
tuner 3-0061: chip found @ 0xc2 (ivtv i2c driver #1)
tda9887 3-0043: chip found @ 0x86 (ivtv i2c driver #1)
wm8775 3-001b: chip found @ 0x36 (ivtv i2c driver #1)
tveeprom 3-0050: Hauppauge model 23552, rev D492, serial# 7894525
tveeprom 3-0050: tuner model is Philips FQ1236A MK4 (idx 92, type 57)
tveeprom 3-0050: TV standards NTSC(M) (eeprom 0x08)
tveeprom 3-0050: second tuner model is Philips TEA5768HL FM Radio (idx
101, type 62)
tveeprom 3-0050: audio processor is CX25843 (idx 37)
tveeprom 3-0050: decoder processor is CX25843 (idx 30)
tveeprom 3-0050: has radio, has no IR remote
ivtv1: This is the second unit of a PVR500
ivtv1: Correcting tveeprom data: no radio present on second unit
ivtv1: loaded v4l-cx2341x-enc.fw firmware (262144 bytes)
ivtv1: Encoder revision: 0x02050032
ivtv1: Allocate DMA encoder MPEG stream: 128 x 32768 buffers (4096KB total)
ivtv1: Allocate DMA encoder YUV stream: 194 x 10800 buffers (2048KB total)
ivtv1: Allocate DMA encoder VBI stream: 120 x 17472 buffers (2048KB total)
ivtv1: Allocate DMA encoder PCM audio stream: 455 x 4608 buffers (2048KB
total)
tuner 3-0061: type set to 57 (Philips FQ1236A MK4)
ivtv1: i2c hardware 0x00000001 not found for command 0xc008561c!
ivtv1: i2c addr 0x44 not found for command 0x40045613!
ivtv1: i2c addr 0x44 not found for command 0xc0045627!
ivtv1: i2c addr 0x44 not found for command 0x40345622!
ivtv1: i2c addr 0x44 not found for command 0x40045612!
ivtv1: i2c hardware 0x00000001 not found for command 0xc008561c!
ivtv1: i2c hardware 0x00000001 not found for command 0xc008561c!
ivtv1: i2c addr 0x44 not found for command 0x40045613!
ivtv1: i2c addr 0x44 not found for command 0x40045612!
ivtv1: i2c hardware 0x00000001 not found for command 0xc008561c!
ivtv1: Initialized WinTV PVR 500 (unit #2), card #1
ivtv:  ====================  END INIT IVTV  ====================