[mythtv-users] no audio PVR-500

Wed May 17 04:25:59 UTC 2006

I just upgraded everything via AT rpms, so I am now at:

ivtv-0.6.2-110.rhfc5.at
kernel-2.6.16-1.2111_FC5smp
mythtv-0.19-128.rhfc5.at

Other sound applications work fine, and recordings made through the
PVR-500 before the upgrade play back with sound. But recordings made now
have no audio. This happens on both tuners, for both recordings and Live
TV. I am at my wits end. I have searched the archives, and there are
references to having to run ivtvctl, but that was for very old versions
of the drivers I believe, and I tried it anyway with no success. My
system is useless without the audio and the WAF is at zero (and will go
negative if we get a silent Dr. Who on Friday night )-:

Anybody have any ideas what I could look for? I have attached the ivtv
part of the dmesg output.

I don't want to blame AT rpms for this, because I have also had to
restore my system from backup after my attempt to install Windows so
that I could run Powerstrip destroyed my whole system. My only
alternative if I cannot fix this problem will be a complete reinstall
from scratch, and I really did have other plans for this weekend )-:

--Greg

-------------- next part --------------
ivtv:  ========== START INIT IVTV ==========
ivtv:  version 0.6.2 (development snapshot compiled on Mon May  8 07:36:28 2006) loading
ivtv:  Linux version: 2.6.16-1.2111_FC5smp SMP 686 REGPARM 4KSTACKS gcc-4.1
ivtv:  In case of problems please include the debug info between
ivtv:  the START INIT IVTV and END INIT IVTV lines, along with
ivtv:  any module options, when mailing the ivtv-users mailinglist.
ACPI: PCI Interrupt 0000:02:03.0[A] -> GSI 20 (level, low) -> IRQ 20
PCI: Via IRQ fixup for 0000:02:03.0, from 11 to 4
ohci1394: fw-host0: OHCI-1394 1.0 (PCI): IRQ=[20]  MMIO=[f7eff800-f7efffff]  Max Packet=[2048]  IR/IT contexts=[4/8]
ivtv0: Autodetected Hauppauge WinTV PVR-150 card (cx23416 based)
ACPI: PCI Interrupt 0000:00:1d.2[C] -> GSI 18 (level, low) -> IRQ 16
PCI: Setting latency timer of device 0000:00:1d.2 to 64
uhci_hcd 0000:00:1d.2: UHCI Host Controller
ACPI: PCI Interrupt 0000:03:08.0[A] -> GSI 21 (level, low) -> IRQ 21
uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 3
uhci_hcd 0000:00:1d.2: irq 16, io base 0x0000ef40
usb usb3: configuration #1 chosen from 1 choice
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 2 ports detected
tveeprom 1-0050: Hauppauge model 23552, rev D492, serial# 8428542
tveeprom 1-0050: tuner model is Philips FQ1236A MK4 (idx 92, type 57)
tveeprom 1-0050: TV standards NTSC(M) (eeprom 0x08)
tveeprom 1-0050: second tuner model is Philips TEA5768HL FM Radio (idx 101, type 62)
tveeprom 1-0050: audio processor is CX25843 (idx 37)
tveeprom 1-0050: decoder processor is CX25843 (idx 30)
tveeprom 1-0050: has radio, has no IR remote
ivtv0: This is the first unit of a PVR500
usb 1-1: new low speed USB device using uhci_hcd and address 2
ACPI: PCI Interrupt 0000:00:1d.3[A] -> GSI 16 (level, low) -> IRQ 17
PCI: Setting latency timer of device 0000:00:1d.3 to 64
uhci_hcd 0000:00:1d.3: UHCI Host Controller
uhci_hcd 0000:00:1d.3: new USB bus registered, assigned bus number 4
uhci_hcd 0000:00:1d.3: irq 17, io base 0x0000ef80
usb usb4: configuration #1 chosen from 1 choice
hub 4-0:1.0: USB hub found
hub 4-0:1.0: 2 ports detected
tuner 1-0060: TEA5767 detected.
tuner 1-0060: chip found @ 0xc0 (ivtv i2c driver #0)
tuner 1-0060: type set to 62 (Philips TEA5767HN FM Radio)
tuner 1-0061: chip found @ 0xc2 (ivtv i2c driver #0)
ACPI: PCI Interrupt 0000:00:1d.7[D] -> GSI 23 (level, low) -> IRQ 22
PCI: Setting latency timer of device 0000:00:1d.7 to 64
ehci_hcd 0000:00:1d.7: EHCI Host Controller
ehci_hcd 0000:00:1d.7: debug port 1
PCI: cache line size of 128 is not supported by device 0000:00:1d.7
ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 5
ehci_hcd 0000:00:1d.7: irq 22, io mem 0xf7fffc00
ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
usb usb5: configuration #1 chosen from 1 choice
hub 5-0:1.0: USB hub found
hub 5-0:1.0: 8 ports detected
usb 1-1: configuration #1 chosen from 1 choice
usb 1-1: can't set config #1, error -71
usb 1-1: USB disconnect, address 2
tda9887 1-0043: chip found @ 0x86 (ivtv i2c driver #0)
cx25840 1-0044: cx25843-23 found @ 0x88 (ivtv i2c driver #0)
cx2388x dvb driver version 0.0.5 loaded
cx25840 1-0044: unable to open firmware v4l-cx25840.fw
wm8775 1-001b: chip found @ 0x36 (ivtv i2c driver #0)
usb 1-1: new low speed USB device using uhci_hcd and address 3
ieee1394: Host added: ID:BUS[0-00:1023]  GUID[0011d8000092ecee]
ieee1394: Node added: ID:BUS[0-01:1023]  GUID[00152ffffeda33ac]
usb 1-1: configuration #1 chosen from 1 choice
ivtv0: loaded v4l-cx2341x-enc.fw firmware (262144 bytes)
ieee1394: raw1394: /dev/raw1394 device initialized
usb 1-2: new low speed USB device using uhci_hcd and address 4
ivtv0: Encoder revision: 0x02040024
ivtv0: Allocate DMA encoder MPEG stream: 128 x 32768 buffers (4096KB total)
ivtv0: Allocate DMA encoder YUV stream: 194 x 10800 buffers (2048KB total)
ivtv0: Allocate DMA encoder VBI stream: 120 x 17472 buffers (2048KB total)
ivtv0: Allocate DMA encoder PCM audio stream: 455 x 4608 buffers (2048KB total)
ivtv0: Create encoder radio stream
tuner 1-0061: type set to 57 (Philips FQ1236A MK4)
usb 1-2: configuration #1 chosen from 1 choice
ivtv0: Initialized WinTV PVR 500 (unit #1), card #0
ivtv:  ===========  NEXT CARD  ===========
ivtv1: Autodetected Hauppauge WinTV PVR-150 card (cx23416 based)
ACPI: PCI Interrupt 0000:03:09.0[A] -> GSI 22 (level, low) -> IRQ 18
tuner 2-0061: chip found @ 0xc2 (ivtv i2c driver #1)
tda9887 2-0043: chip found @ 0x86 (ivtv i2c driver #1)
cx25840 2-0044: cx25843-23 found @ 0x88 (ivtv i2c driver #1)
cx25840 2-0044: unable to open firmware v4l-cx25840.fw
wm8775 2-001b: chip found @ 0x36 (ivtv i2c driver #1)
tveeprom 2-0050: Hauppauge model 23552, rev D492, serial# 8428542
tveeprom 2-0050: tuner model is Philips FQ1236A MK4 (idx 92, type 57)
tveeprom 2-0050: TV standards NTSC(M) (eeprom 0x08)
tveeprom 2-0050: second tuner model is Philips TEA5768HL FM Radio (idx 101, type 62)
tveeprom 2-0050: audio processor is CX25843 (idx 37)
tveeprom 2-0050: decoder processor is CX25843 (idx 30)
tveeprom 2-0050: has radio, has no IR remote
ivtv1: This is the second unit of a PVR500
ivtv1: Correcting tveeprom data: no radio present on second unit
hiddev96: USB HID v1.10 Device [American Power Conversion Back-UPS RS 1500 FW:8.g9 .D USB FW:g9 ] on usb-0000:00:1d.0-2
ivtv1: loaded v4l-cx2341x-enc.fw firmware (262144 bytes)
ivtv1: Encoder revision: 0x02040024
ivtv1: Allocate DMA encoder MPEG stream: 128 x 32768 buffers (4096KB total)
ivtv1: Allocate DMA encoder YUV stream: 194 x 10800 buffers (2048KB total)
ivtv1: Allocate DMA encoder VBI stream: 120 x 17472 buffers (2048KB total)
ivtv1: Allocate DMA encoder PCM audio stream: 455 x 4608 buffers (2048KB total)
tuner 2-0061: type set to 57 (Philips FQ1236A MK4)
ivtv1: Initialized WinTV PVR 500 (unit #2), card #1
ivtv:  ==========  END INIT IVTV  ==========