[mythtv-users] Live TV not working

Jim jim at jimmygoogle.com
Sat Aug 25 15:21:24 UTC 2007


I have been poking around some more and I got this output. 

The output for `v4l2-ctl -T`
Tuner:
        Capabilities         : 62.5 kHz
        Frequency range      : 0.0 MHz - 0.0 MHz
        Signal strength      : 0%
        Current audio mode   : mono
        Available subchannels:

I tried swapping cables. Is my card dead? Does anyone have another checks I can run?

On Thu, 23 Aug 2007 19:25:12 -0400, Jim <jim at jimmygoogle.com> wrote:
> I am having some issues with live playback.  It just started after a
> reboot, I havent changed anything since it was installed.  The
> mythfrontend end returns 'TV Error: LiveTV not successfully started' and
> the channels are all black.  I am thinking its the ivtv driver?  Any
> ideas?
> 
> ivtv:  ==================== START INIT IVTV ====================
> ivtv:  version 0.10.3 (tagged release) loading
> ivtv:  Linux version: 2.6.20-1.2952.fc6 SMP mod_unload
> ivtv:  In case of problems please include the debug info between
> ivtv:  the START INIT IVTV and END INIT IVTV lines, along with
> ivtv:  any module options, when mailing the ivtv-users mailinglist.
> ivtv0: Autodetected Hauppauge card (cx23415 based)
> ACPI: PCI Interrupt Link [LNKA] enabled at IRQ 19
> ACPI: PCI Interrupt 0000:01:08.0[A] -> Link [LNKA] -> GSI 19 (level, low)
> -> IRQ 19
> ivtv0: Unreasonably low latency timer, setting to 64 (was 32)
> input: PC Speaker as /class/input/input3
> nvidia: module license 'NVIDIA' taints kernel.
> parport: PnPBIOS parport detected.
> parport0: PC-style at 0x378 (0x778), irq 7 [PCSPP,TRISTATE]
> sd 0:0:0:0: Attached scsi generic sg0 type 0
> Floppy drive(s): fd0 is 1.44M
> ivtv0: loaded v4l-cx2341x-enc.fw firmware (376836 bytes)
> FDC 0 is a post-1991 82077
> ivtv0: loaded v4l-cx2341x-dec.fw firmware (262144 bytes)
> ivtv0: Encoder revision: 0x02060039
> ivtv0: Decoder revision: 0x02020023
> tveeprom 0-0050: Hauppauge model 48132, rev K268, serial# 9888664
> tveeprom 0-0050: tuner model is LG TAPE H001F MK3 (idx 68, type 47)
> tveeprom 0-0050: TV standards NTSC(M) (eeprom 0x08)
> tveeprom 0-0050: audio processor is MSP4448 (idx 27)
> tveeprom 0-0050: decoder processor is SAA7115 (idx 19)
> tveeprom 0-0050: has radio, has IR receiver, has no IR transmitter
> ivtv0: Autodetected Hauppauge WinTV PVR-350
> saa7115 0-0021: saa7115 found (1f7115d0e100000) @ 0x42 (ivtv i2c driver
> #0)
> ivtv0: Failed to load module saa7127
> ivtv0: Registered device video0 for encoder MPEG (4 MB)
> ivtv0: Registered device video32 for encoder YUV (2 MB)
> ivtv0: Registered device vbi0 for encoder VBI (1 MB)
> ivtv0: Registered device video24 for encoder PCM audio (1 MB)
> ivtv0: Registered device radio0 for encoder radio
> ivtv0: Registered device video16 for decoder MPEG (1 MB)
> ivtv0: Registered device vbi8 for decoder VBI (1 MB)
> ivtv0: Registered device vbi16 for decoder VOUT
> ivtv0: Registered device video48 for decoder YUV (1 MB)
> ivtv0: loaded v4l-cx2341x-init.mpg firmware (155648 bytes)
> ivtv0: i2c hardware 0x00000008 (msp3400) not found for command 0xc008561c!
> ivtv0: i2c hardware 0x00000008 (msp3400) not found for command 0x4008646d!
> ivtv0: i2c hardware 0x00000008 (msp3400) not found for command 0xc008561c!
> ivtv0: i2c hardware 0x00000008 (msp3400) not found for command 0xc008561c!
> ivtv0: i2c hardware 0x00000008 (msp3400) not found for command 0xc008561c!
> ivtv0: Initialized Hauppauge WinTV PVR-350, card #0
> ivtv:  ====================  END INIT IVTV  ====================
> 
> 
> _______________________________________________
> mythtv-users mailing list
> mythtv-users at mythtv.org
> http://mythtv.org/cgi-bin/mailman/listinfo/mythtv-users



More information about the mythtv-users mailing list