[mythtv-users] mythdora 3.2 + air2pc rev1 setup problems

David Murphy dm1000 at gmail.com
Thu Mar 1 01:25:07 UTC 2007


I'm new to mythtv and recently ebay'd an Air2PC rev1 card (broadcom 
demodulator) as an inexpensive way to see what OTA HDTV reception would 
be like at my location.  I've installed Mythdora 3.2 in a seperate 
frontend and backend configuration and have used it successfully as a 
file player/dvd server for the past week while I awaited arrival of the 
Air2PC card.  My backend hardware is pretty marginal but it just a 
temporary rig to play with.

When the Air2PC card arrived today I did a clean install on the backend.

When I go to set up the capture card on the backend I choose card type: 
DVB DTV capture card(v3.x).  In the box below I see: Frontend ID: Could 
not open card #0 subtype: No such file or directory

I understand that this card requires a firmware file and I have verified 
that dvb-fe-bcm3510-01.fw exists within /lib/firmware

I am unsure as to how to proceed. Dmesg is pasted below:

Thanks for your time.


Linux version 2.6.18-1.2257.fc5smp 
(brewbuilder at ls20-bc1-14.build.redhat.com) (g 
                                                cc version 4.1.1 
20060525 (Red Hat 4.1.1-1)) #1 SMP Fri Dec 15 16:33:51 EST 2006
BIOS-provided physical RAM map:
  BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)
  BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
  BIOS-e820: 00000000000e0000 - 0000000000100000 (reserved)
  BIOS-e820: 0000000000100000 - 0000000017fe0000 (usable)
  BIOS-e820: 0000000017fe0000 - 0000000017ff0000 (ACPI data)
  BIOS-e820: 0000000017ff0000 - 0000000018000000 (ACPI NVS)
  BIOS-e820: 00000000fff80000 - 0000000100000000 (reserved)
0MB HIGHMEM available.
383MB LOWMEM available.
Using x86 segment limits to approximate NX protection
On node 0 totalpages: 98272
   DMA zone: 4096 pages, LIFO batch:0
   Normal zone: 94176 pages, LIFO batch:31
DMI 2.3 present.
Using APIC driver default
ACPI: RSDP (v000 AMI                                   ) @ 0x000fbf50
ACPI: RSDT (v001 AMIINT AMIINT10 0x00001000 MSFT 0x0100000b) @ 0x17fe0000
ACPI: FADT (v001 AMIINT AMIINT10 0x00001000 MSFT 0x0100000b) @ 0x17fe0030
ACPI: DSDT (v001  INTEL   SOLANO 0x00001000 MSFT 0x0100000b) @ 0x00000000
ACPI: PM-Timer IO Port: 0x408
Allocating PCI resources starting at 20000000 (gap: 18000000:e7f80000)
Detected 701.631 MHz processor.
Built 1 zonelists.  Total pages: 98272
Kernel command line: ro root=/dev/rootvg/rootlv01
Local APIC disabled by BIOS -- you can enable it with "lapic"
mapped APIC to ffffd000 (0130c000)
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Initializing CPU#0
CPU 0 irqstacks, hard=c07a3000 soft=c0783000
PID hash table entries: 2048 (order: 11, 8192 bytes)
Console: colour VGA+ 80x25
Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
Memory: 382944k/393088k available (2111k kernel code, 9516k reserved, 
850k data, 
              244k init, 0k highmem)
Checking if this processor honours the WP bit even in supervisor mode... Ok.
Calibrating delay using timer specific routine.. 1404.01 BogoMIPS 
(lpj=702005)
Security Framework v1.0.0 initialized
SELinux:  Initializing.
SELinux:  Starting in permissive mode
selinux_register_security:  Registering secondary module capability
Capability LSM initialized as secondary
Mount-cache hash table entries: 512
CPU: After generic identify, caps: 0383f9ff 00000000 00000000 00000000 
00000000 
            00000000 00000000
CPU: After vendor identify, caps: 0383f9ff 00000000 00000000 00000000 
00000000 0 
             0000000 00000000
CPU: L1 I cache: 16K, L1 D cache: 16K
CPU: L2 cache: 256K
CPU: After all inits, caps: 0383f1ff 00000000 00000000 00000040 00000000 
0000000 
          0 00000000
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#0.
Checking 'hlt' instruction... OK.
SMP alternatives: switching to UP code
Freeing SMP alternatives: 12k freed
ACPI: Core revision 20060707
ACPI: setting ELCR to 0800 (from 0e20)
CPU0: Intel Pentium III (Coppermine) stepping 03
SMP motherboard not detected.
Local APIC not detected. Using dummy APIC emulation.
Brought up 1 CPUs
sizeof(vma)=88 bytes
sizeof(page)=32 bytes
sizeof(inode)=424 bytes
sizeof(dentry)=148 bytes
sizeof(ext3inode)=600 bytes
sizeof(buffer_head)=52 bytes
sizeof(skbuff)=172 bytes
sizeof(task_struct)=1408 bytes
checking if image is initramfs... it is
Freeing initrd memory: 1671k freed
NET: Registered protocol family 16
ACPI: bus type pci registered
PCI: PCI BIOS revision 2.10 entry at 0xfdb21, last bus=2
PCI: Using configuration type 1
Setting up standard PCI resources
ACPI: Interpreter enabled
ACPI: Using PIC for interrupt routing
ACPI: PCI Root Bridge [PCI0] (0000:00)
PCI: Probing PCI hardware (bus 00)
PCI quirk: region 0400-047f claimed by ICH4 ACPI/GPIO/TCO
PCI quirk: region 0480-04bf claimed by ICH4 GPIO
Boot video device is 0000:01:00.0
PCI: Firmware left 0000:02:0a.0 e100 interrupts enabled, disabling
PCI: Transparent bridge - 0000:00:1e.0
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.ICH_._PRT]
ACPI: Power Resource [URP1] (off)
ACPI: Power Resource [URP2] (off)
ACPI: Power Resource [FDDP] (off)
ACPI: Power Resource [LPTP] (off)
ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 6 7 *9 10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 6 7 9 10 *11 12 14 15)
ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 5 6 7 9 10 *11 12 14 15)
ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 *5 6 7 9 10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 6 7 9 10 11 12 14 15) *0, 
disabled.
ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 6 7 9 10 11 12 14 15) *0, 
disabled.
ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 5 6 7 9 10 11 12 14 15) *0, 
disabled.
ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 5 6 7 9 *10 11 12 14 15)
Linux Plug and Play Support v0.97 (c) Adam Belay
pnp: PnP ACPI init
pnp: PnP ACPI: found 12 devices
usbcore: registered new driver usbfs
usbcore: registered new driver hub
PCI: Using ACPI for IRQ routing
PCI: If a device doesn't work, try "pci=routeirq".  If it helps, post a 
report
PCI: Bridge: 0000:00:01.0
   IO window: 9000-9fff
   MEM window: ee900000-ef9fffff
   PREFETCH window: e2600000-e66fffff
PCI: Bridge: 0000:00:1e.0
   IO window: a000-afff
   MEM window: efa00000-efefffff
   PREFETCH window: e6700000-e67fffff
PCI: Setting latency timer of device 0000:00:1e.0 to 64
NET: Registered protocol family 2
IP route cache hash table entries: 4096 (order: 2, 16384 bytes)
TCP established hash table entries: 16384 (order: 6, 327680 bytes)
TCP bind hash table entries: 8192 (order: 5, 163840 bytes)
TCP: Hash tables configured (established 16384 bind 8192)
TCP reno registered
apm: BIOS not found.
audit: initializing netlink socket (disabled)
audit(1172691380.007:1): initialized
Total HugeTLB memory allocated, 0
VFS: Disk quotas dquot_6.5.1
Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
SELinux:  Registering netfilter hooks
Initializing Cryptographic API
ksign: Installing public key data
Loading keyring
- Added public key DA272E53BD0532F6
- User ID: Red Hat, Inc. (Kernel Module GPG key)
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered (default)
pci_hotplug: PCI Hot Plug PCI Core version: 0.5
ACPI: CPU0 (power states: C1[C1] C2[C2] C3[C3])
ACPI: Processor [CPU1] (supports 8 throttling states)
isapnp: Scanning for PnP cards...
isapnp: No Plug & Play device found
Real Time Clock Driver v1.12ac
Non-volatile memory driver v1.2
Linux agpgart interface v0.101 (c) Dave Jones
agpgart: Detected an Intel i815 Chipset.
agpgart: AGP aperture is 64M @ 0xe8000000
Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled
serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
serial8250: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
00:09: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
00:0a: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
RAMDISK driver initialized: 16 RAM disks of 16384K size 4096 blocksize
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
ICH2: IDE controller at PCI slot 0000:00:1f.1
ICH2: chipset revision 2
ICH2: not 100% native mode: will probe irqs later
     ide0: BM-DMA at 0xffa0-0xffa7, BIOS settings: hda:DMA, hdb:pio
     ide1: BM-DMA at 0xffa8-0xffaf, BIOS settings: hdc:pio, hdd:DMA
Probing IDE interface ide0...
hda: Maxtor 96147U8, ATA DISK drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
Probing IDE interface ide1...
hdd: Pioneer DVD-ROM ATAPIModel DVD-106S 010, ATAPI CD/DVD-ROM drive
ide1 at 0x170-0x177,0x376 on irq 15
hda: max request size: 128KiB
hda: 120060864 sectors (61471 MB) w/2048KiB Cache, CHS=65535/16/63, UDMA(66)
hda: cache flushes not supported
  hda: hda1 hda2 hda3
ide-floppy driver 0.99.newide
usbcore: registered new driver libusual
usbcore: registered new driver hiddev
usbcore: registered new driver usbhid
drivers/usb/input/hid-core.c: v2.6:USB HID core driver
PNP: PS/2 Controller [PNP0303:PS2K,PNP0f03:PS2M] at 0x60,0x64 irq 1,12
serio: i8042 AUX port at 0x60,0x64 irq 12
serio: i8042 KBD port at 0x60,0x64 irq 1
mice: PS/2 mouse device common for all mice
md: md driver 0.90.3 MAX_MD_DEVS=256, MD_SB_DISKS=27
md: bitmap version 4.39
TCP bic registered
Initializing IPsec netlink socket
NET: Registered protocol family 1
NET: Registered protocol family 17
Using IPI No-Shortcut mode
ACPI: (supports S0 S1<6>Time: tsc clocksource has been installed.
  S3 S4 S5)
Freeing unused kernel memory: 244k freed
Write protecting the kernel read-only data: 382k
Time: acpi_pm clocksource has been installed.
input: AT Translated Set 2 keyboard as /class/input/input0
input: ImPS/2 Generic Wheel Mouse as /class/input/input1
device-mapper: ioctl: 4.7.0-ioctl (2006-06-24) initialised: 
dm-devel at redhat.com
kjournald starting.  Commit interval 5 seconds
EXT3-fs: mounted filesystem with ordered data mode.
SELinux:  Disabled at runtime.
SELinux:  Unregistering netfilter hooks
audit(1172691384.250:2): selinux=0 auid=4294967295
snd_page_alloc: no version for "struct_module" found: kernel tainted.
input: PC Speaker as /class/input/input2
Intel 82802 RNG detected
hdd: ATAPI 40X DVD-ROM drive, 256kB Cache, UDMA(66)
Uniform CD-ROM driver Revision: 3.20
ACPI: PCI Interrupt Link [LNKB] enabled at IRQ 11
PCI: setting IRQ 11 as level-triggered
ACPI: PCI Interrupt 0000:00:1f.5[B] -> Link [LNKB] -> GSI 11 (level, 
low) -> IRQ 
               11
PCI: Setting latency timer of device 0000:00:1f.5 to 64
intel8x0_measure_ac97_clock: measured 50489 usecs
intel8x0: clocking to 48000
ACPI: PCI Interrupt Link [LNKA] enabled at IRQ 9
PCI: setting IRQ 9 as level-triggered
ACPI: PCI Interrupt 0000:01:00.0[A] -> Link [LNKA] -> GSI 9 (level, low) 
-> IRQ 
          9
matroxfb: Matrox Millennium G400 MAX (AGP) detected
PInS memtype = 0
matroxfb: MTRR's turned on
matroxfb: 640x480x8bpp (virtual: 640x26214)
matroxfb: framebuffer at 0xE4000000, mapped to 0xd8980000, size 33554432
Console: switching to colour frame buffer device 80x30
fb0: MATROX frame buffer device
e100: Intel(R) PRO/100 Network Driver, 3.5.10-k2-NAPI
e100: Copyright(c) 1999-2005 Intel Corporation
ACPI: PCI Interrupt Link [LNKC] enabled at IRQ 11
ACPI: PCI Interrupt 0000:02:0a.0[A] -> Link [LNKC] -> GSI 11 (level, 
low) -> IRQ 
               11
e100: eth0: e100_probe: addr 0xefeff000, irq 11, MAC addr 00:D0:B7:BD:1B:CC
Floppy drive(s): fd0 is 1.44M, fd1 is 1.44M
FDC 0 is a post-1991 82077
USB Universal Host Controller Interface driver v3.0
ACPI: PCI Interrupt Link [LNKD] enabled at IRQ 5
PCI: setting IRQ 5 as level-triggered
ACPI: PCI Interrupt 0000:00:1f.2[D] -> Link [LNKD] -> GSI 5 (level, low) 
-> IRQ 
          5
PCI: Setting latency timer of device 0000:00:1f.2 to 64
uhci_hcd 0000:00:1f.2: UHCI Host Controller
uhci_hcd 0000:00:1f.2: new USB bus registered, assigned bus number 1
uhci_hcd 0000:00:1f.2: irq 5, io base 0x0000cc00
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
ACPI: PCI Interrupt Link [LNKH] enabled at IRQ 10
PCI: setting IRQ 10 as level-triggered
ACPI: PCI Interrupt 0000:00:1f.4[C] -> Link [LNKH] -> GSI 10 (level, 
low) -> IRQ 
               10
PCI: Setting latency timer of device 0000:00:1f.4 to 64
uhci_hcd 0000:00:1f.4: UHCI Host Controller
uhci_hcd 0000:00:1f.4: new USB bus registered, assigned bus number 2
uhci_hcd 0000:00:1f.4: irq 10, io base 0x0000d400
usb usb2: configuration #1 chosen from 1 choice
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
parport: PnPBIOS parport detected.
parport0: PC-style at 0x378 (0x778), irq 7 [PCSPP,TRISTATE,EPP]
lp0: using parport0 (interrupt-driven).
lp0: console ready
ACPI: Power Button (FF) [PWRF]
ACPI: Power Button (CM) [PWRB]
ACPI: Sleep Button (CM) [SLPB]
ibm_acpi: ec object not found
md: Autodetecting RAID arrays.
md: autorun ...
md: ... autorun DONE.
EXT3 FS on dm-0, internal journal
kjournald starting.  Commit interval 5 seconds
EXT3 FS on hda1, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
kjournald starting.  Commit interval 5 seconds
EXT3 FS on dm-2, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
Adding 950264k swap on /dev/rootvg/rootlv02.  Priority:-1 extents:1 
across:95026 
               4k
e100: eth0: e100_watchdog: link up, 100Mbps, full-duplex
Bluetooth: Core ver 2.10
NET: Registered protocol family 31
Bluetooth: HCI device and connection manager initialized
Bluetooth: HCI socket layer initialized
Bluetooth: L2CAP ver 2.8
Bluetooth: L2CAP socket layer initialized
Bluetooth: RFCOMM socket layer initialized
Bluetooth: RFCOMM TTY layer initialized
Bluetooth: RFCOMM ver 1.8
Bluetooth: HIDP (Human Interface Emulation) ver 1.1
NET: Registered protocol family 10
lo: Disabled Privacy Extensions
IPv6 over IPv4 tunneling driver
Installing knfsd (copyright (C) 1996 okir at monad.swb.de).
NFSD: Using /var/lib/nfs/v4recovery as the NFSv4 state recovery directory
NFSD: unable to find recovery directory /var/lib/nfs/v4recovery
NFSD: starting 90-second grace period
eth0: no IPv6 routers present
Linux video capture interface: v2.00
cx2388x cx88-mpeg Driver Manager version 0.0.6 loaded
cx2388x dvb driver version 0.0.6 loaded
cx8802_register_driver() ->registering driver type=dvb access=shared
cx2388x alsa driver version 0.0.6 loaded
saa7130/34: v4l2 driver version 0.2.14 loaded
saa7134 ALSA driver for DMA sound loaded
saa7134 ALSA: no saa7134 cards found
b2c2-flexcop: B2C2 FlexcopII/II(b)/III digital TV receiver chip loaded 
successfu 
            lly
usbcore: registered new driver cinergyT2
saa7146: register extension 'budget dvb'.
saa7146: register extension 'dvb'.
bttv: driver version 0.9.16 loaded
bttv: using 8 buffers with 2080k (520 pages) each for capture
bt878: AUDIO driver version 0.0.0 loaded
saa7146: register extension 'budget_av'.
saa7146: register extension 'budget_ci dvb'.
em28xx v4l2 driver version 0.0.1 loaded
usbcore: registered new driver em28xx
[drm] Initialized drm 1.0.1 20051102
[drm] Initialized mga 3.2.1 20051102 on minor 0
agpgart: Found an AGP 2.0 compliant device at 0000:00:00.0.
agpgart: Putting AGP V2 device at 0000:00:00.0 into 1x mode
agpgart: Putting AGP V2 device at 0000:01:00.0 into 1x mode
[drm] Initialized card for AGP DMA.



More information about the mythtv-users mailing list