No subject

#Chosen IR Transmitter
TRANSMITTER="HD-PVR"
TRANSMITTER_MODULES="lirc_zilog"
TRANSMITTER_DRIVER=""
TRANSMITTER_DEVICE="/dev/lirc0"
TRANSMITTER_SOCKET=""
TRANSMITTER_LIRCD_CONF="/etc/lirc/lircd.conf"
TRANSMITTER_LIRCD_ARGS=""

Results from:  ls /dev/lirc*

/dev/lirc0

So, as far as I can tell, I have things correct. Yet I cannot get a
connection using *irsend*. Not mater what I do I get the error

irsend: could not connect to socket
irsend: No such file or directory

Can anyone please help me further with this as I have googled to the point
where I have seen and read all the info out there.

Thanks, in advance, for any help that can be had!

--0022152d6cb5a3a18b0497a3d645
Content-Type: text/html; charset=ISO-8859-1
Content-Transfer-Encoding: quoted-printable

I had the hdpvr working fine, including blaster on my ubuntu 10.04 backend.=
 The blaster recently stopped working, I believe it was due to the latest k=
ernel update, 2.6.36. <br><br>I went through the complete procedure to get =
working, which I successfully did a couple months ago, but no luck after at=
 least 8 hours of work. I tried rebooting using the previous kernel version=
 but that didn&#39;t help either. <br>
<br>So, I am looking desperately for help. <br><br>Here is what I have for =
status:<br>root at myth2:/home/mark# dmesg|grep lirc<br>[=A0 297.789423] lirc_=
dev: IR Remote Control driver registered, major 249 <br>[=A0 297.801777] li=
rc_zilog: Zilog/Hauppauge IR driver initializing<br>
[=A0 297.810574] lirc_zilog: chip found with RX and TX<br>[=A0 297.810712] =
lirc_dev: lirc_register_driver: sample_rate: 0<br>[=A0 298.129836] lirc_zil=
og: Zilog/Hauppauge IR blaster firmware version 2.1.0 loaded<br>[=A0 298.12=
9939] lirc_zilog: initialization complete<br>
<br>I assume this means the drivers are installed and working properly...<b=
r><br><br>From my file: /etc/lirc/hardware.conf<br><br>#Chosen IR Transmitt=
er<br>TRANSMITTER=3D&quot;HD-PVR&quot;<br>TRANSMITTER_MODULES=3D&quot;lirc_=
zilog&quot;<br>
TRANSMITTER_DRIVER=3D&quot;&quot;<br>TRANSMITTER_DEVICE=3D&quot;/dev/lirc0&=
quot;<br>TRANSMITTER_SOCKET=3D&quot;&quot;<br>TRANSMITTER_LIRCD_CONF=3D&quo=
t;/etc/lirc/lircd.conf&quot;<br>TRANSMITTER_LIRCD_ARGS=3D&quot;&quot;<br><b=
r>Results from:=A0 ls /dev/lirc*<br>
<br>/dev/lirc0<br><br>So, as far as I can tell, I have things correct. Yet =
I cannot get a connection using <b>irsend</b>. Not mater what I do I get th=
e error <br><br>irsend: could not connect to socket<br>irsend: No such file=
 or directory<br>
<br>Can anyone please help me further with this as I have googled to the po=
int where I have seen and read all the info out there.<br><br>Thanks, in ad=
vance, for any help that can be had!<br><br><br>

--0022152d6cb5a3a18b0497a3d645--