[mythtv-users] When Installing a second Pinnacle tune card, it's default configuration is analog, not the QAM Samsung my first card has.

[Ron Harm]

> It looks like you did something like "dmesg | grep cx88".  Don't do
> that.  It sounds like a good idea but it fails to show lines for other
> parts of the tuner board which don't happen to have that string.
> Instead please just post the full dmesg output, or if you are
> uncomfortable doing that then post everything after the line "cx2388x
> v4l2 driver version 0.0.7 loaded".

I tried sending the entire dmesg output but the email message was too
large.  Please let me know if the below is what you need:

Dec 12 12:43:44 ron-dvr kernel: [    7.264464] cx88/0: cx2388x v4l2 driver
version 0.0.7 loaded
Dec 12 12:43:44 ron-dvr kernel: [    7.264512] cx8800 0000:03:06.0: PCI INT
A -> GSI 21 (level, low) -> IRQ 21
Dec 12 12:43:44 ron-dvr kernel: [    7.264722] cx88[0]: subsystem:
11bd:0051, board: Pinnacle PCTV HD 800i [card=58,autodetected], frontend(s):
1
Dec 12 12:43:44 ron-dvr kernel: [    7.264724] cx88[0]: TV tuner type 76,
Radio tuner type -1
Dec 12 12:43:44 ron-dvr kernel: [    7.266694] cx88/2: cx2388x MPEG-TS
Driver Manager version 0.0.7 loaded
Dec 12 12:43:44 ron-dvr kernel: [    7.292282] cx2388x alsa driver version
0.0.7 loaded
Dec 12 12:43:44 ron-dvr kernel: [    7.301012] HDA Intel 0000:00:14.2: PCI
INT A -> GSI 16 (level, low) -> IRQ 16
Dec 12 12:43:44 ron-dvr kernel: [    7.567231] HDA Intel 0000:01:05.1: PCI
INT B -> GSI 19 (level, low) -> IRQ 19
Dec 12 12:43:44 ron-dvr kernel: [    7.577291] tuner 2-0064: chip found @
0xc8 (cx88[0])
Dec 12 12:43:44 ron-dvr kernel: [    7.783438] cfg80211: World regulatory
domain updated:
Dec 12 12:43:44 ron-dvr kernel: [    7.783441]  (start_freq - end_freq @
bandwidth), (max_antenna_gain, max_eirp)
Dec 12 12:43:44 ron-dvr kernel: [    7.783444]  (2402000 KHz - 2472000 KHz @
40000 KHz), (300 mBi, 2000 mBm)
Dec 12 12:43:44 ron-dvr kernel: [    7.783446]  (2457000 KHz - 2482000 KHz @
20000 KHz), (300 mBi, 2000 mBm)
Dec 12 12:43:44 ron-dvr kernel: [    7.783449]  (2474000 KHz - 2494000 KHz @
20000 KHz), (300 mBi, 2000 mBm)
Dec 12 12:43:44 ron-dvr kernel: [    7.783451]  (5170000 KHz - 5250000 KHz @
40000 KHz), (300 mBi, 2000 mBm)
Dec 12 12:43:44 ron-dvr kernel: [    7.783452]  (5735000 KHz - 5835000 KHz @
40000 KHz), (300 mBi, 2000 mBm)
Dec 12 12:43:44 ron-dvr kernel: [    7.868620] xc5000 2-0064: creating new
instance
Dec 12 12:43:44 ron-dvr kernel: [    7.869761] xc5000: Successfully
identified at address 0x64
Dec 12 12:43:44 ron-dvr kernel: [    7.869762] xc5000: Firmware has not been
loaded previously
Dec 12 12:43:44 ron-dvr kernel: [    7.869766] cx88[0]: Calling XC5000
callback
Dec 12 12:43:44 ron-dvr kernel: [    7.869828] input: cx88 IR (Pinnacle PCTV
HD 800i) as /devices/pci0000:00/0000:00:14.4/0000:03:06.0/input/input5
Dec 12 12:43:44 ron-dvr kernel: [    7.869885] cx88[0]/0: found at
0000:03:06.0, rev: 5, irq: 21, latency: 64, mmio: 0xfd000000
Dec 12 12:43:44 ron-dvr kernel: [    7.869896] IRQ 21/cx88[0]: IRQF_DISABLED
is not guaranteed on shared IRQs
Dec 12 12:43:44 ron-dvr kernel: [    7.869940] cx88[0]/0: registered device
video0 [v4l2]
Dec 12 12:43:44 ron-dvr kernel: [    7.869963] cx88[0]/0: registered device
vbi0
Dec 12 12:43:44 ron-dvr kernel: [    7.872305] xc5000: waiting for firmware
upload (dvb-fe-xc5000-1.6.114.fw)...
Dec 12 12:43:44 ron-dvr kernel: [    8.026705] xc5000: firmware uploading...
Dec 12 12:43:44 ron-dvr kernel: [    8.026708] cx88[0]: Calling XC5000
callback
-------------- next part --------------
An HTML attachment was scrubbed...
URL: <http://mythtv.org/pipermail/mythtv-users/attachments/20101216/7e1cdfbc/attachment.htm>