[mythtv-users] When Installing a second Pinnacle tune card, it's default configuration is analog, not the QAM Samsung my first card has.
Ron Harm
rharm49 at gmail.com
Sat Dec 18 01:27:48 UTC 2010
>> It looks like you did something like "dmesg | grep cx88". Don't do
>> that. It sounds like a good idea but it fails to show lines for other
>> parts of the tuner board which don't happen to have that string.
>> Instead please just post the full dmesg output, or if you are
>> uncomfortable doing that then post everything after the line "cx2388x
>> v4l2 driver version 0.0.7 loaded".
>
> I tried sending the entire dmesg output but the email message was too
> large. Please let me know if the below is what you need:
<snip>
> I probably need the next twenty or thirty lines after what you provided.
1. 10.180046] cx88/0: cx2388x v4l2 driver version 0.0.7 loaded
2. [ 10.180088] alloc irq_desc for 20 on node -1
3. [ 10.180090] alloc kstat_irqs on node -1
4. [ 10.180105] cx8800 0000:03:05.0: PCI INT A -> GSI 20 (level, low)
-> IRQ 20
5. [ 10.180319] cx88[0]: subsystem: 11bd:0051, board: Pinnacle PCTV HD
800i [card=58,autodetected], frontend(s): 1
6. [ 10.180322] cx88[0]: TV tuner type 76, Radio tuner type -1
7. [ 10.182223] cx88/2: cx2388x MPEG-TS Driver Manager version 0.0.7
loaded
8. [ 10.297544] HDA Intel 0000:00:14.2: PCI INT A -> GSI 16 (level,
low) -> IRQ 16
9. [ 10.388861] tuner 2-0064: chip found @ 0xc8 (cx88[0])
10. [ 10.398418] cx2388x alsa driver version 0.0.7 loaded
11. [ 10.734219] cfg80211: World regulatory domain updated:
12. [ 10.734222] (start_freq - end_freq @ bandwidth),
(max_antenna_gain, max_eirp)
13. [ 10.734225] (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi,
2000 mBm)
14. [ 10.734228] (2457000 KHz - 2482000 KHz @ 20000 KHz), (300 mBi,
2000 mBm)
15. [ 10.734230] (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi,
2000 mBm)
16. [ 10.734232] (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi,
2000 mBm)
17. [ 10.734234] (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi,
2000 mBm)
18. [ 10.747388] HDA Intel 0000:01:05.1: PCI INT B -> GSI 19 (level,
low) -> IRQ 19
19. [ 10.747421] HDA Intel 0000:01:05.1: setting latency timer to 64
20. [ 10.753857] phy0: Selected rate control algorithm 'minstrel'
21. [ 10.754524] phy0: hwaddr 00:e0:4c:03:fd:0b, RTL8187vB (default) V1
+ rtl8225z2, rfkill mask 2
22. [ 10.765314] rtl8187: Customer ID is 0x00
23. [ 10.765349] Registered led device: rtl8187-phy0::tx
24. [ 10.765363] Registered led device: rtl8187-phy0::rx
25. [ 10.765799] rtl8187: wireless switch is on
26. [ 10.765827] usbcore: registered new interface driver rtl8187
27. [ 10.932365] xc5000 2-0064: creating new instance
28. [ 10.933516] xc5000: Successfully identified at address 0x64
29. [ 10.933517] xc5000: Firmware has not been loaded previously
30. [ 10.933521] cx88[0]: Calling XC5000 callback
31. [ 10.933589] input: cx88 IR (Pinnacle PCTV HD 800i) as
/devices/pci0000:00/0000:00:14.4/0000:03:05.0/input/input5
32. [ 10.933646] cx88[0]/0: found at 0000:03:05.0, rev: 5, irq: 20,
latency: 64, mmio: 0xfd000000
33. [ 10.933657] IRQ 20/cx88[0]: IRQF_DISABLED is not guaranteed on
shared IRQs
34. [ 10.933704] cx88[0]/0: registered device video0 [v4l2]
35. [ 10.933729] cx88[0]/0: registered device vbi0
36. [ 10.936068] xc5000: waiting for firmware upload
(dvb-fe-xc5000-1.6.114.fw)...
37. [ 10.936072] cx8800 0000:03:05.0: firmware: requesting
dvb-fe-xc5000-1.6.114.fw
38. [ 11.088658] xc5000: firmware read 12401 bytes.
39. [ 11.088661] xc5000: firmware uploading...
40. [ 11.088664] cx88[0]: Calling XC5000 callback
41. [ 13.026427] type=1505 audit(1292461501.545:6):
operation="profile_replace" pid=940 name="/sbin/dhclient3"
42. [ 13.026660] type=1505 audit(1292461501.545:7):
operation="profile_replace" pid=940
name="/usr/lib/NetworkManager/nm-dhcp-client.action"
43. [ 13.026796] type=1505 audit(1292461501.545:8):
operation="profile_replace" pid=940
name="/usr/lib/connman/scripts/dhclient-script"
44. [ 13.180156] type=1505 audit(1292461501.697:9):
operation="profile_load" pid=941 name="/usr/bin/evince"
45. [ 13.183093] type=1505 audit(1292461501.701:10):
operation="profile_load" pid=941 name="/usr/bin/evince-previewer"
46. [ 13.184890] type=1505 audit(1292461501.701:11):
operation="profile_load" pid=941 name="/usr/bin/evince-thumbnailer"
47. [ 13.448682] xc5000: firmware upload complete...
48. [ 14.100098] cx88[0]/2: cx2388x 8802 Driver Manager
49. [ 14.100120] cx88-mpeg driver manager 0000:03:05.2: PCI INT A ->
GSI 20 (level, low) -> IRQ 20
50. [ 14.100131] cx88[0]/2: found at 0000:03:05.2, rev: 5, irq: 20,
latency: 64, mmio: 0xfb000000
51. [ 14.100137] IRQ 20/cx88[0]: IRQF_DISABLED is not guaranteed on
shared IRQs
52. [ 14.100209] cx88_audio 0000:03:05.1: PCI INT A -> GSI 20 (level,
low) -> IRQ 20
53. [ 14.100222] IRQ 20/cx88[0]: IRQF_DISABLED is not guaranteed on
shared IRQs
54. [ 14.100243] cx88[0]/1: CX88x/0: ALSA support for cx2388x boards
55. [ 14.154455] cx88/2: cx2388x dvb driver version 0.0.7 loaded
56. [ 14.154459] cx88/2: registering cx8802 driver, type: dvb access:
shared
57. [ 14.154462] cx88[0]/2: subsystem: 11bd:0051, board: Pinnacle PCTV
HD 800i [card=58]
58. [ 14.154465] cx88[0]/2: cx2388x based DVB/ATSC card
59. [ 14.154467] cx8802_alloc_frontends() allocating 1 frontend(s)
60. [ 14.206094] cx88[0]: Calling XC5000 callback
61. [ 14.385572] xc5000 2-0064: attaching existing instance
62. [ 14.386699] xc5000: Successfully identified at address 0x64
63. [ 14.386701] xc5000: Firmware has been loaded previously
64. [ 14.388213] DVB: registering new adapter (cx88[0])
65. [ 14.388216] DVB: registering adapter 0 frontend 0 (Samsung S5H1409
QAM/8VSB Frontend)...
66. [ 15.350093] r8169: eth0: link down
67. [ 15.350274] ADDRCONF(NETDEV_UP): eth0: link is not ready
68. [ 16.400124] __ratelimit: 9 callbacks suppressed
69. [ 16.400127] type=1505 audit(1292461504.917:15):
operation="profile_replace" pid=1169 name="/usr/sbin/mysqld"
70. [ 17.341982] ADDRCONF(NETDEV_UP): wlan0: link is not ready
71. [ 19.748025] [drm:drm_mode_getfb] *ERROR* invalid framebuffer id
72. [ 22.337699] CPU0 attaching NULL sched-domain.
73. [ 22.337705] CPU1 attaching NULL sched-domain.
74. [ 22.337708] CPU2 attaching NULL sched-domain.
75. [ 22.337710] CPU3 attaching NULL sched-domain.
76. [ 22.373066] CPU0 attaching sched-domain:
77. [ 22.373070] domain 0: span 0-3 level MC
78. [ 22.373073] groups: 0 1 2 3
79. [ 22.373078] CPU1 attaching sched-domain:
80. [ 22.373080] domain 0: span 0-3 level MC
81. [ 22.373082] groups: 1 2 3 0
82. [ 22.373089] CPU2 attaching sched-domain:
83. [ 22.373090] domain 0: span 0-3 level MC
84. [ 22.373092] groups: 2 3 0 1
85. [ 22.373096] CPU3 attaching sched-domain:
86. [ 22.373097] domain 0: span 0-3 level MC
87. [ 22.373099] groups: 3 0 1 2
88. [ 38.805460] wlan0: deauthenticating from 00:24:01:cf:24:4d by
local choice (reason=3)
89. [ 38.917411] wlan0: direct probe to AP 00:24:01:cf:24:4d (try 1)
90. [ 38.921791] wlan0: direct probe responded
91. [ 38.921794] wlan0: authenticate with AP 00:24:01:cf:24:4d (try 1)
92. [ 38.923284] wlan0: authenticated
93. [ 38.923307] wlan0: associate with AP 00:24:01:cf:24:4d (try 1)
94. [ 38.926664] wlan0: RX AssocResp from 00:24:01:cf:24:4d
(capab=0x421 status=0 aid=1)
95. [ 38.926668] wlan0: associated
96. [ 38.928593] ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
97. [ 703.908777] cx88[0]: Calling XC5000 callback
98. [ 728.472431] type=1505 audit(1292462216.992:16):
operation="profile_replace" pid=2877 name="/usr/sbin/mysqld"
99. [ 728.472859] type=1505 audit(1292462216.992:17):
operation="profile_replace" pid=2878 name="/usr/sbin/ntpd"
100. [ 728.514585] type=1505 audit(1292462217.032:18):
operation="profile_replace" pid=2874 name="/sbin/dhclient3"
101. [ 728.514678] type=1505 audit(1292462217.032:19):
operation="profile_replace" pid=2874
name="/usr/lib/NetworkManager/nm-dhcp-client.action"
102. [ 728.514735] type=1505 audit(1292462217.032:20):
operation="profile_replace" pid=2874
name="/usr/lib/connman/scripts/dhclient-script"
103. [ 728.536003] type=1505 audit(1292462217.052:21):
operation="profile_replace" pid=2879 name="/usr/sbin/tcpdump"
104. [ 732.228476] type=1505 audit(1292462220.745:22):
operation="profile_replace" pid=2875 name="/usr/bin/evince"
105. [ 732.229331] type=1505 audit(1292462220.749:23):
operation="profile_replace" pid=2875 name="/usr/bin/evince-previewer"
106. [ 732.229926] type=1505 audit(1292462220.749:24):
operation="profile_replace" pid=2875 name="/usr/bin/evince-thumbnailer"
107. [ 736.071915] __ratelimit: 18 callbacks suppressed
108. [ 736.071919] type=1505 audit(1292462224.589:31):
operation="profile_replace" pid=2909 name="/usr/bin/evince"
109. [ 736.072744] type=1505 audit(1292462224.589:32):
operation="profile_replace" pid=2909 name="/usr/bin/evince-previewer"
110. [ 736.073374] type=1505 audit(1292462224.593:33):
operation="profile_replace" pid=2909 name="/usr/bin/evince-thumbnailer"
111. [142914.961081] wlan0: deauthenticated from 00:24:01:cf:24:4d
(Reason: 6)
112. [142917.248723] wlan0: direct probe to AP 00:24:01:cf:24:4d (try 1)
113. [142917.252979] wlan0: direct probe responded
114. [142917.252984] wlan0: authenticate with AP 00:24:01:cf:24:4d (try
1)
115. [142917.254471] wlan0: authenticated
116. [142917.254490] wlan0: associate with AP 00:24:01:cf:24:4d (try 1)
117. [142917.258222] wlan0: RX AssocResp from 00:24:01:cf:24:4d
(capab=0x421 status=0 aid=1)
118. [142917.258227] wlan0: associated
-------------- next part --------------
An HTML attachment was scrubbed...
URL: <http://mythtv.org/pipermail/mythtv-users/attachments/20101217/ea942264/attachment-0001.htm>
More information about the mythtv-users
mailing list