[mythtv-users] tveeprom 2-0050: Huh, no eeprom present (err=-6)?

[coffee]

Hello Everyone,

I have just subscribed to the list again. 

The other day my remote control quit working. HUmmmm? I have not done
any upgrades and have the correct settings
set in the mythtvfrontend setup for the remote. But going thru my logs I
found the following error:

tveeprom 2-0050: Huh, no eeprom present (err=-6)?
tveeprom 2-0050: Encountered bad packet header [5c]. Corrupt or not a
Hauppauge eeprom.
ivtv1: Invalid EEPROM
cx25840 2-0044: cx25  0-21 found @ 0x88 (ivtv i2c driver #1)
wm8775 2-001b: chip found @ 0x36 (ivtv i2c driver #1)
wm8775 2-001b: I2C: cannot write 000 to register R23
wm8775 2-001b: I2C: cannot write 000 to register R7
wm8775 2-001b: I2C: cannot write 021 to register R11
wm8775 2-001b: I2C: cannot write 102 to register R12
wm8775 2-001b: I2C: cannot write 000 to register R13
wm8775 2-001b: I2C: cannot write 1d4 to register R14
wm8775 2-001b: I2C: cannot write 1d4 to register R15
wm8775 2-001b: I2C: cannot write 1bf to register R16
wm8775 2-001b: I2C: cannot write 185 to register R17
wm8775 2-001b: I2C: cannot write 0a2 to register R18
wm8775 2-001b: I2C: cannot write 005 to register R19
wm8775 2-001b: I2C: cannot write 07a to register R20
wm8775 2-001b: I2C: cannot write 102 to register R21

Now, I noticed that no /dev/lirc* at all. Therefore somehow my receiver
on the card is borked I guess.


I have 2 PVR-150's in a box running Fedora 11. I use one receiver port
on one card to do my remote that came with
one of the pvr150s. 

Both cards are working and recording shows with no problems except no
remote control.

System information:

Mythtv .22

Linux mythtv.athome.net 2.6.30.10-105.2.23.fc11.x86_64 #1 SMP Thu Feb 11
07:06:34 UTC 2010 x86_64 x86_64 x86_64 GNU/Linux

lirc-0.8.6-2.fc11.x86_64

snippet of logs pertaining to ivtv: (First pvr150 no problems, Second
card - Oops)

ivtv0: Initializing card 0
ivtv0: Autodetected Hauppauge card (cx23416 based)
ivtv0: Autodetected Hauppauge WinTV PVR-150
ivtv0: Reopen i2c bus for IR-blaster support
IRQ 20/ivtv0: IRQF_DISABLED is not guaranteed on shared IRQs
ivtv0: Registered device video0 for encoder MPG (4096 kB)
ivtv0: Registered device video32 for encoder YUV (2048 kB)
ivtv0: Registered device vbi0 for encoder VBI (1024 kB)
ivtv0: Registered device video24 for encoder PCM (320 kB)
ivtv0: Initialized card: Hauppauge WinTV PVR-150
ivtv0: Loaded v4l-cx2341x-enc.fw firmware (376836 bytes)
ivtv0: Encoder revision: 0x02060039


ivtv1: Initializing card 1
ivtv1: Autodetected Hauppauge card (cx23416 based)
ivtv1: Invalid EEPROM
IRQ 22/ivtv1: IRQF_DISABLED is not guaranteed on shared IRQs
ivtv1: Registered device video1 for encoder MPG (4096 kB)
ivtv1: Registered device video33 for encoder YUV (2048 kB)
ivtv1: Registered device vbi1 for encoder VBI (1024 kB)
ivtv1: Registered device video25 for encoder PCM (320 kB)
ivtv1: Registered device radio1 for encoder radio
ivtv1: Initialized card: Hauppauge WinTV PVR-150
ivtv1: Loaded v4l-cx2341x-enc.fw firmware (376836 bytes)
ivtv1: Encoder revision: 0x02060039

Here is some more lovely information:
ivtv1: Initializing card 1
ivtv1: Autodetected Hauppauge card (cx23416 based)
ivtv 0000:04:07.0: PCI INT A -> GSI 22 (level, low) -> IRQ 22
tveeprom 2-0050: Huh, no eeprom present (err=-6)?
tveeprom 2-0050: Encountered bad packet header [5c]. Corrupt or not a
Hauppauge eeprom.
ivtv1: Invalid EEPROM
cx25840 2-0044: cx25  0-21 found @ 0x88 (ivtv i2c driver #1)
wm8775 2-001b: chip found @ 0x36 (ivtv i2c driver #1)
wm8775 2-001b: I2C: cannot write 000 to register R23
wm8775 2-001b: I2C: cannot write 000 to register R7
wm8775 2-001b: I2C: cannot write 021 to register R11
wm8775 2-001b: I2C: cannot write 102 to register R12
wm8775 2-001b: I2C: cannot write 000 to register R13
wm8775 2-001b: I2C: cannot write 1d4 to register R14
wm8775 2-001b: I2C: cannot write 1d4 to register R15
wm8775 2-001b: I2C: cannot write 1bf to register R16
wm8775 2-001b: I2C: cannot write 185 to register R17
wm8775 2-001b: I2C: cannot write 0a2 to register R18
wm8775 2-001b: I2C: cannot write 005 to register R19
wm8775 2-001b: I2C: cannot write 07a to register R20
wm8775 2-001b: I2C: cannot write 102 to register R21
IRQ 22/ivtv1: IRQF_DISABLED is not guaranteed on shared IRQs
ivtv1: Registered device video1 for encoder MPG (4096 kB)
ivtv1: Registered device video33 for encoder YUV (2048 kB)
ivtv1: Registered device vbi1 for encoder VBI (1024 kB)
ivtv1: Registered device video25 for encoder PCM (320 kB)
ivtv1: Registered device radio1 for encoder radio
ivtv1: Initialized card: Hauppauge WinTV PVR-150
ivtv: End initialization



-------------------------------------------------

Im thinking right now, Swap the receiver to the other cards port and
perhaps back in business? Can I get that lucky? 

thanks for any input on this problem,

coffee412


-------------- next part --------------
An HTML attachment was scrubbed...
URL: <http://mythtv.org/pipermail/mythtv-users/attachments/20100526/9c380d4d/attachment.htm>