ATI HDTV Wonder
From MythTV
With the release of the 2.6.15 kernel, this HDTV capture card is partly useable with MythTV. Although this card has no official Linux support, unlike other cards such as the DVICO Fusion, Air2PC and pcHDTV cards, there probably some that bought this card for Windows MCE, only to realize later that MCE is not stable with HDTV content. So you've moved on and up to MythTV and want to put this card to use.
Contents |
Compatibility
The ATI HDTV Wonder can be used for digital or analog channels, and will coincide nicely with standard definition cards using the ivtv drivers, like the Hauppauge PVR-150 - 500 cards, as well as other HDTV cards using the cx88-dvb drivers, such as the pcHDTV. It's not officially supported by ATI under Linux. Although it has an analog tuner onboard, there is no hardware mpeg2 encoder so this task will cause a certain load on your processor. In a system with enough processor performance both the analog and digital tuner will work. The digital tuner IS capable of tuning clear (unencrypted) QAM 256 channels. Most cable providers have the local channels in HD in this QAM 256 format. The card will lock to encrypted and unencrypted QAM 256 channels, but only unencrypted ones will be viewable. The input used for QAM seems to depend on either the version of the card or version of the kernel.
Some have reported that the HDTV Wonder seems to stutter and glitch slightly more than a side-by-side comparison to a pcHDTV 5500, while others have seen it perform just as well compared to a pcHDTV 3000.
Auto detecting by the kernel starts with 2.6.18.1 and above, before that the latest Video4Linux drivers had to be installed.
Warning: Kernel's 2.6.20 to 2.6.20.3 (tested) are broken. Kernel 2.6.21.x and above are fixed.
openSUSE 10.2
The ATI HDTV card has been successfully implemented by users into their SuSE 10.1 and 10.2 mythTV boxes. With openSUSE 10.2, this card is almost ready to go. There are only a few steps to start receiving HDTV signals. The default kernel with openSUSE 10.2 is already configured correctly and the "Kernel Configuration" section can be skipped.
Ubuntu 7.04 (Feisty Fawn)
After installing Feisty Fawn, this card is almost ready to go. There are only a few steps to start receiving HDTV signals. The default kernel with Ubuntu 7.04 is already configured correctly and the "Kernel Configuration" section can be skipped.
Ubuntu 7.10 (Gusty Gibbon)
The DTV tuner is already preinstalled with this version of Ubuntu. With the default drivers, the DTV tuner can be used with either analog or digital channels.
Kernel Configuration
Kernel >= 2.6.15
Device Drivers -->
I2C support -->
<*> I2C support
<*> I2C device interface
I2C Algorithms --->
<*> I2C bit-banging interfaces
Multimedia Devices -->
<*> Video For Linux -->
Video For Linux -->
<M> Conexant 2388x (bt878 successor) support
<M> DVB/ATSC Support for cx2388x based TV cards
[ ] Build all supported frontends for cx2388x based TV cards
[*] NXT2002/NXT2004 ATSC Support
Digital Video Broadcasting Devices --->
[*] DVB For Linux
Customise DVB Frontends --->
<M> Nextwave NXT2002/NXT2004 based
Loading the Software
openSUSE 10.2
On openSUSE 10.2, use YaST to install the "dvb" package
YaST -> Software -> Software Maintenance -> search -> dvb
Select the "dvb" package, and choose "Accept". It should now install.
Ubuntu 7.04
Create the location to download the firmware
mkdir /usr/share/doc/dvb cd /usr/share/doc/dvb
Go to this site and copy the script and paste it into a file named "get_dvb_firmware": http://www.mjmwired.net/kernel/Documentation/dvb/get_dvb_firmware
NOTE: Be sure to remove the numbers and spaces at the beginning
- You can do this easily by clicking the "Hide Line Numbers" button on the top of that page Prindle19 18:43, 19 August 2007 (UTC)
Other Flavors
If you are using another flavor, use your package manager and search for and install "dvb".
Once "dvb" has been installed, you are ready to continue loading the firmware and the drivers.
Loading the Firmware
You also need to download the appropriate firmware files for this card. Fortunately, a script is provided with the kernel to automate this process.
openSUSE 10.2
In openSUSE 10.2, the default "kernel source directory" is /usr/src/linux-2.6.18.2-34. Here are the openSUSE specific commands. First use the "get_dvb_firmware" script to download the firmware:
# cd /usr/src/linux-2.6.18.2-34 # chmod +x Documentation/dvb/get_dvb_firmware # ./Documentation/dvb/get_dvb_firmware nxt2004
Copy dvb-fe-nxt2004.fw to the firmware directory:
# cp dvb-fe-nxt2004.fw /lib/firmware
Ubuntu 7.04
Add execute permissions to the file and execute it:
# cd /usr/share/doc/dvb # chmod +x ./get_dvb_firmware # ./get_dvb_firmware nxt2004
The following files should be downloaded automatically:
AVerTVHD_MCE_A180_Drv_v1.2.2.16.zip dvb-fe-nxt2004.fwAVerTVHD_MCE_A180_Drv_v1.2.2.16.zip dvb-fe-nxt2004.fw
Copy the firmware file to the location Ubuntu expects it to be:
# cp ./dvb-fe-nxt2004.fw /lib/firmware
Other Flavors
The following commands need to be run from the kernel source directory.
# chmod +x Documentation/dvb/get_dvb_firmware # ./Documentation/dvb/get_dvb_firmware nxt2004
Then copy dvb-fe-nxt2004.fw to your firmware directory (varies depending on your hotplug version) using one of the command below:
# cp dvb-fe-nxt2004.fw /usr/lib/hotplug/firmware
Loading the Drivers (all flavors)
To load the drivers, load cx88-dvb with:
# modprobe cx88-dvb
To verify it loaded properly, look for something similar to this near the end of the 'dmesg' output:
# dmesg cx2388x dvb driver version 0.0.5 loaded CORE cx88[0]: subsystem: 1002:a101, board: ATI HDTV Wonder [card=34,autodetected ] TV tuner 68 at 0x1fe, Radio tuner -1 at 0x1fe tuner 1-0061: chip found @ 0xc2 (cx88[0]) tuner 1-0061: type set to 68 (Philips TUV1236D ATSC/NTSC dual in) PCI: Found IRQ 9 for device 0000:02:0b.2 cx88[0]/2: found at 0000:02:0b.2, rev: 5, irq: 9, latency: 32, mmio: 0xe1000000 cx88[0]/2: cx2388x based dvb card nxt200x: NXT2004 Detected DVB: registering new adapter (cx88[0]). DVB: registering frontend 0 (Nextwave NXT200X VSB/QAM frontend)...
Testing the card
The card should be found in /dev/dvb/adapter0. Assuming you have the dvb-tools package installed and a .azap/channels.conf file, you can run azap:
# azap -r KUTV-HD using '/dev/dvb/adapter0/frontend0' and '/dev/dvb/adapter0/demux0' tuning to 593000000 Hz video pid 0x0031, audio pid 0x0034 status 00 | signal f603 | snr fbf7 | ber 00000000 | unc 00000000 | status 1f | signal ef9c | snr fbb5 | ber 00000000 | unc 00000000 | FE_HAS_LOCK
If you are unable to use the "azap", don't lose hope. Continue configuring mythTV and once it is configured correctly, HDTV channels should lock in.
Once the tuner is accessed for the first time (i.e. when you try and watch live TV in the mythfrontend), you can verify the firmware was uploaded properly by searching for this output in dmesg:
# dmesg | grep nxt2004 nxt2004: Waiting for firmware upload (dvb-fe-nxt2004.fw)... nxt2004: Waiting for firmware upload(2)... nxt2004: Firmware upload complete
Configuring mythTV
Using mythtvsetup, configure the card as you would any other dvb frontend card.
I specifically bought this card to tune in Terrestrial channels coming over my Cox Cable connection. Here is how I configured it and actually got it to work!
# mythtvsetup
First, setup the capture card:
2. Capture Cards
New Capture Card
DVB DTV Capture Card (v3.x)
DVB Card Number: 0
DiSEqC
Description: LNB
LNB Preset: Linear (N. America)
LNB Type: Standard (Voltage)
Finish
Recorder Options
Wait for SEQ start Header - checked!
Open DVB card on demand - unchecked
DVB Tuning Delay: 0
Finish
Finish
Setup the Video Source. This doesn't get you any TV listings, but it works. Perhaps someone else can update this further.
3. Video Sources
New Video Source
Video Source Name: CABLE-HDTV
XMLTV Listings: North America (DataDirect)
Channel Frequency Table: default
Finish
Setup the Input Connections to match the card with the video source.
4. Input Connections
New Input
Select "DVB : 0"
Display Name: ATI-HDTV
Video Source: CABLE-HDTV
DVB Options:
Free to air channels only - checked!
Radio Channels - checked!
Use Dish Long-term EIT Data - unchecked
Scan for Channels
Scan Type: Full Scan
Frequencey Table: Broadcast
ATSC Modulation: Terrestrial (8-VSB)
Channel Separator: (5_1) Underscore
Existing Channel Treatment: Minimal Updates
Next <--- The scanning process will take a long time!
Verify the output, checking for "Locked" channels.
Exit mythtvsetup with the Esc key
You should have received some locked-in channels. If you did, start up your front end and check for Live HDTV! If not, check your settings again and rescan. You may have to change some of them based on who your cable provider is and/or where you live. Again, I was able to use these settings to pick up unencrypted channels from Cox.
Here is another page that may help with the mythtvsetup HDTV setup process, but it was writen for a previous version of mythTV:
http://www.digitalregime.com/mythdvb/setup/
