User:Sdkovacs

My Setup on Fedora 8

Capture Cards

PVR350 (using TV out)

PVR150

System specs

PIII 800 384MB RAM

• Hard Drive 1 - 25GB

** /
** /boot
** swap

• Hard Drive 2 - 320GB

** /videos

Xorg

Posted here is my xorg.conf file for the PVR350 with TVOUT. I had to change a few lines between Fedora 6 and Fedora 8 because of the change in the ivtv driver.

</pre>

1. XFree86 4 configuration created by pyxf86config

Section "ServerLayout"

       Identifier     "Default Layout"
       Screen      0  "Screen0" 0 0
       InputDevice    "Mouse0" "CorePointer"
       InputDevice    "Keyboard0" "CoreKeyboard"

EndSection

Section "Files"

1. RgbPath is the location of the RGB database. Note, this is the name of the
2. file minus the extension (like ".txt" or ".db"). There is normally
3. no need to change the default.
4. Multiple FontPath entries are allowed (they are concatenated together)
5. By default, Red Hat 6.0 and later now use a font server independent of
6. the X server to render fonts.

1. ModulePath "/usr/lib/xorg/modules/extensions/nvidia"
2. ModulePath "/usr/lib/xorg/modules/extensions"
3. ModulePath "/usr/lib/xorg/modules"
4. FontPath "unix/:7100"

EndSection

Section "Module"

       Load  "dbe"
       Load  "extmod"
       Load  "fbdevhw"
       Load  "glx"
       Load  "record"
       Load  "freetype"
       Load  "type1"
       Load  "vnc"

EndSection

Section "InputDevice"

1. Specify which keyboard LEDs can be user-controlled (eg, with xset(1))
2. Option "Xleds" "1 2 3"
3. To disable the XKEYBOARD extension, uncomment XkbDisable.
4. Option "XkbDisable"
5. To customise the XKB settings to suit your keyboard, modify the
6. lines below (which are the defaults). For example, for a non-U.S.
7. keyboard, you will probably want to use:
8. Option "XkbModel" "pc102"
9. If you have a US Microsoft Natural keyboard, you can use:
10. Option "XkbModel" "microsoft"
12. Then to change the language, change the Layout setting.
13. For example, a german layout can be obtained with:
14. Option "XkbLayout" "de"
15. or:
16. Option "XkbLayout" "de"
17. Option "XkbVariant" "nodeadkeys"
19. If you'd like to switch the positions of your capslock and
20. control keys, use:
21. Option "XkbOptions" "ctrl:swapcaps"
22. Or if you just want both to be control, use:
23. Option "XkbOptions" "ctrl:nocaps"

       Identifier  "Keyboard0"

Driver "kbd"

       Option      "XkbModel" "pc105"
       Option      "XkbLayout" "us"

EndSection

Section "InputDevice"

       Identifier  "Mouse0"
       Driver      "mouse"
       Option      "Protocol" "IMPS/2"
       Option      "Device" "/dev/input/mice"
       Option      "ZAxisMapping" "4 5"
       Option      "Emulate3Buttons" "no"

EndSection

Section "InputDevice"

1. If the normal CorePointer mouse is not a USB mouse then
2. this input device can be used in AlwaysCore mode to let you
3. also use USB mice at the same time.

       Identifier  "DevInputMice"
       Driver      "mouse"
       Option      "Protocol" "IMPS/2"
       Option      "Device" "/dev/input/mice"
       Option      "ZAxisMapping" "4 5"
       Option      "Emulate3Buttons" "no"

EndSection

Section "Monitor"

       Identifier  "NTSC Monitor"
       HorizSync  30-68
       VertRefresh 50-120
       Mode "720x480"
         # D: 34.563 MHz, H: 37.244 kHz, V: 73.897 Hz
         DotClock 34.564
         HTimings 720 752 840 928
         VTimings 480 484 488 504
         Flags    "-HSync" "-VSync"
     EndMode

EndSection

Section "Device"

       Identifier  "Hauppauge PVR 350 iTVC15 Framebuffer"
       Driver      "ivtv"

       ### change fb1 to whatever your card grabbed
       Option      "fbdev" "/dev/fb1"
       Option      "ivtv" "/dev/fb1"

       ### change the BusID to whatever is reported by lspci,
       ### converted from hex to decimal
       BusID "PCI:2:10:0" # lspci says 02:0a.0
       #BusID "PCI:0:8:0" # lspci says 00:08.0
       ### More examples
       #BusID "PCI:0:10:0" # lspci says 00:0a.0
       #BusID "PCI:1:14:0" # lspci says 01:0e.0
       #BusID "PCI:0:5:1" # lspci says 00:05.1

EndSection

Section "Screen"

       Identifier  "Screen0"
       Device      "Hauppauge PVR 350 iTVC15 Framebuffer"
       Monitor     "NTSC Monitor"
       Option "SecurityTypes" "VncAuth"
       Option "UserPasswdVerifier" "VncAuth"
       Option "PasswordFile" "/home/mythtv/.vnc/passwd"
       DefaultDepth 24
       DefaultFbbpp 32
       Subsection "Display"
         Depth 24
         FbBpp 32
         Modes "720x480"
       EndSubsection

EndSection

Section "DRI"

       Group        0
       Mode         0666

EndSection