User:AndrewAllison
From MythTV Official Wiki
Revision as of 17:21, 17 November 2011 by AndrewAllison (talk | contribs)
Hardware
Asus M4A77TD motherboard AMD Phenom II X4 965 Processor nVidia Corporation NV44 [GeForce 6200 TurboCache Hauppaupe 150 with ir input Hauppauge 150 Hauppauge 500
Standard Files
Because these files are spread out everywhere, I usually get a mismatched set :-(
/etc/my.cnf
[mysqld] datadir=/var/lib/mysql socket=/var/lib/mysql/mysql.sock user=mysql # Disabling symbolic-links is recommended to prevent assorted security risks symbolic-links=0 key_buffer = 16M table_cache = 128 sort_buffer_size = 2M myisam_sort_buffer_size = 8M query_cache_size = 16M [mysqld_safe] log-error=/var/log/mysqld.log pid-file=/var/run/mysqld/mysqld.pid
/etc/lircmd
# # lircmd config file # PROTOCOL IntelliMouse # ACCELERATOR start max multiplier ACCELERATOR 2 30 5 ACTIVATE * RESERVED MOVE_N * 2 MOVE_NE * 3 MOVE_E * 6 MOVE_SE * 9 MOVE_S * 8 MOVE_SW * 7 MOVE_W * 4 MOVE_NW * 1 MOVE_IN * CH+ MOVE_OUT * CH- BUTTON1_TOGGLE * 5 BUTTON1_TOGGLE * RADIO BUTTON2_TOGGLE * VOL+ BUTTON3_TOGGLE * SOURCE BUTTON1_CLICK * TV BUTTON1_CLICK * VOL- BUTTON3_CLICK * MUTE # BUTTONx_CLICK, BUTTONx_UP, BUTTONx_DOWN are also possible
/etc/lirc/lircd.conf
#
# this config file was automatically generated
# using lirc-0.5.5pre8 on Sun Apr 18 11:43:45 1999
#
# contributed by Jens Leuschner <leuschner@gmx.net>
#
# brand: Hauppauge
# model:
# supported devices: WinTV primo; WinTV pci; WinTV radio
#
# This config file will work with both homebrew receivers and
# original Hauppauge TV cards !!!
#
begin remote
name Hauppauge
bits 13
flags SHIFT_ENC
eps 30
aeps 100
one 950 830
zero 950 830
plead 960
gap 89584
repeat_bit 2
begin codes
TV 0x000000000000100F
RADIO 0x000000000000100C
FULL_SCREEN 0x000000000000102E
CH+ 0x0000000000001020
CH- 0x0000000000001021
VOL- 0x0000000000001011
VOL+ 0x0000000000001010
MUTE 0x000000000000100D
SOURCE 0x0000000000001022
1 0x0000000000001001
2 0x0000000000001002
3 0x0000000000001003
4 0x0000000000001004
5 0x0000000000001005
6 0x0000000000001006
7 0x0000000000001007
8 0x0000000000001008
9 0x0000000000001009
0 0x0000000000001000
RESERVED 0x000000000000101E
MINIMIZE 0x0000000000001026
end codes
end remote
#
# this config file was automatically generated
# using lirc-0.6.6(animax) on Tue Apr 15 19:50:27 2003
#
# contributed by
#
# brand: Hauppauge
# model no. of remote control:
# devices being controlled by this remote: PVR 2/350
#
begin remote
name hauppauge_pvr
bits 13
flags RC5|CONST_LENGTH
eps 30
aeps 100
one 969 811
zero 969 811
plead 1097
gap 114605
toggle_bit 2
begin codes
Power 0x00000000000017FD
Go 0x00000000000017FB
1 0x00000000000017C1
2 0x00000000000017C2
3 0x00000000000017C3
4 0x00000000000017C4
5 0x00000000000017C5
6 0x00000000000017C6
7 0x00000000000017C7
8 0x00000000000017C8
9 0x00000000000017C9
Back/Exit 0x00000000000017DF
0 0x00000000000017C0
Menu 0x00000000000017CD
Red 0x00000000000017CB
Green 0x00000000000017EE
Yellow 0x00000000000017F8
Blue 0x00000000000017E9
Ch+ 0x00000000000017E0
Ch- 0x00000000000017E1
Vol- 0x00000000000017D1
Vol+ 0x00000000000017D0
Ok 0x00000000000017E5
Mute 0x00000000000017CF
Blank 0x00000000000017CC
Full 0x00000000000017FC
Rewind 0x00000000000017F2
Play 0x00000000000017F5
Forward 0x00000000000017F4
Record 0x00000000000017F7
Stop 0x00000000000017F6
Pause 0x00000000000017F0
Replay 0x00000000000017E4
Skip 0x00000000000017DE
end codes
end remote
#
# this config file was automatically generated
# using lirc-0.7.0(any) on Sun Nov 28 20:25:09 2004
#
# contributed by
#
# brand: Hauppauge 350
# Created: G.J. Werler (The Netherlands)
# Project: Mythtv Fedora Pundit-R www.mythtvportal.com
# Date: 2004/11/28
# model no. of remote control: Hauppauge A415-HPG
# devices being controlled by this remote: PVR-350
#
begin remote
name Hauppauge_350
bits 13
flags RC5|CONST_LENGTH
eps 30
aeps 100
one 969 811
zero 969 811
plead 1097
gap 114605
toggle_bit 2
begin codes
Go 0x00000000000017BB
Power 0x00000000000017BD
TV 0x000000000000179C
Videos 0x0000000000001798
Music 0x0000000000001799
Pictures 0x000000000000179A
Guide 0x000000000000179B
Radio 0x000000000000178C
Up 0x0000000000001794
Left 0x0000000000001796
Right 0x0000000000001797
Down 0x0000000000001795
OK 0x00000000000017A5
Back/Exit 0x000000000000179F
Menu/i 0x000000000000178D
Vol+ 0x0000000000001790
Vol- 0x0000000000001791
Prev.Ch 0x0000000000001792
Mute 0x000000000000178F
Ch+ 0x00000000000017A0
Ch- 0x00000000000017A1
Record 0x00000000000017B7
Stop 0x00000000000017B6
Rewind 0x00000000000017B2
Play 0x00000000000017B5
Forward 0x00000000000017B4
Replay/SkipBackward 0x00000000000017A4
Pause 0x00000000000017B0
SkipForward 0x000000000000179E
1 0x0000000000001781
2 0x0000000000001782
3 0x0000000000001783
4 0x0000000000001784
5 0x0000000000001785
6 0x0000000000001786
7 0x0000000000001787
8 0x0000000000001788
9 0x0000000000001789
Asterix 0x000000000000178A
0 0x0000000000001780
# 0x000000000000178E
Red 0x000000000000178B
Green 0x00000000000017AE
Yellow 0x00000000000017B8
Blue 0x00000000000017A9
end codes
end remote
#
# this config file was automatically generated
# using lirc-0.7.0pre4(serial) on Sun Oct 2 00:24:32 2005
#
# contributed by anton|ganthaler.at and juergen.wilhelm|aon.at
# members of linux user group Vorarlberg www.lugv.at
#
# for ir remote controler from Hauppauge WinTV Nexus-S
# most of the keys are supported
#
# brand: Hauppauge
# model no. of remote control: WinTV Nexus-S
# devices being controlled by this remote:
#
begin remote
name Hauppauge_WinTV_Nexus-S
bits 13
flags RC5|CONST_LENGTH
eps 30
aeps 100
one 944 828
zero 944 828
plead 980
gap 113932
min_repeat 1
toggle_bit 2
begin codes
Up 0x0000000000001794
Down 0x0000000000001795
Left 0x0000000000001796
Right 0x0000000000001797
Power 0x00000000000017BD
Ok 0x00000000000017A5
Menu 0x000000000000178D
Back 0x000000000000179F
Red 0x000000000000178B
Green 0x00000000000017AE
Yellow 0x00000000000017B8
Blue 0x00000000000017A9
0 0x0000000000001780
1 0x0000000000001781
2 0x0000000000001782
3 0x0000000000001783
4 0x0000000000001784
5 0x0000000000001785
6 0x0000000000001786
7 0x0000000000001787
8 0x0000000000001788
9 0x0000000000001789
Play 0x00000000000017B5
Pause 0x00000000000017B0
Stop 0x00000000000017B6
Record 0x00000000000017B7
FastFwd 0x00000000000017B4
FastRwd 0x00000000000017B2
Channel+ 0x00000000000017A0
Channel- 0x00000000000017A1
Volume+ 0x0000000000001790
Volume- 0x0000000000001791
Mute 0x000000000000178F
Timers 0x000000000000178A
Recordings 0x000000000000178E
Back 0x000000000000179F
Record 0x00000000000017B7
Pause 0x00000000000017B0
end codes
end remote
#
# this config file was automatically generated
# using lirc-0.8.3pre1(default) on Sat Jun 21 12:36:46 2008
#
# contributed by Matthew Wright
#
# brand: Hauppauge (HRV-1600 RT Remote)
# model no. of remote control: A415-HPG-A
# devices being controlled by this remote:
#
begin remote
name Hauppauge
bits 13
flags RC5|CONST_LENGTH
eps 30
aeps 100
one 919 852
zero 919 852
plead 930
gap 112908
toggle_bit_mask 0x800
begin codes
power 0x17BD
go 0x17BB
tv 0x179C
videos 0x1798
music 0x1799
pictures 0x179A
guide 0x179B
radio 0x178C
exit 0x179F
menu 0x178D
prevch 0x1792
mute 0x178F
up 0x1794
down 0x1795
left 0x1796
right 0x1797
ok 0x17A5
volup 0x1790
voldown 0x1791
chup 0x17A0
chdown 0x17A1
record 0x17B7
stop 0x17B6
rewind 0x17B2
fastfwd 0x17B4
play 0x17B5
replay 0x17A4
skip 0x179E
pause 0x17B0
1 0x1781
2 0x1782
3 0x1783
4 0x1784
5 0x1785
6 0x1786
7 0x1787
8 0x1788
9 0x1789
* 0x178A
0 0x1780
# 0x178E
red 0x178B
green 0x17AE
yellow 0x17B8
blue 0x17A9
sub/cc 0x178E
text 0x178A
home 0x17BB
end codes
end remote
#
# this config file was automatically generated
# using lirc-0.8.5(default) on Wed Dec 30 21:52:35 2009
#
# contributed by
#
# brand: Hauppauge
# model no. of remote control:
# devices being controlled by this remote: MVP
#
begin remote
name Hauppauge_MVP
bits 13
flags RC5|CONST_LENGTH
eps 30
aeps 100
one 912 857
zero 912 857
plead 937
gap 113935
toggle_bit_mask 0x800
begin codes
KEY_1 0x10C1
KEY_2 0x10C2
KEY_3 0x10C3
KEY_4 0x10C4
KEY_5 0x10C5
KEY_6 0x10C6
KEY_7 0x10C7
KEY_8 0x10C8
KEY_9 0x10C9
KEY_0 0x10C0
KEY_POWER 0x10FD
KEY_GOTO 0x10FB
KEY_BACK 0x10DF
KEY_MENU 0x10CD
KEY_RED 0x10CB
KEY_GREEN 0x10EE
KEY_YELLOW 0x10F8
KEY_BLUE 0x10E9
KEY_UP 0x10E0
KEY_DOWN 0x10E1
KEY_LEFT 0x10D1
KEY_RIGHT 0x10D0
KEY_MUTE 0x10CF
KEY_FN_1 0x10CC
KEY_FN_2 0x10FC
KEY_OK 0x10E5
KEY_REWIND 0x10F2
KEY_FASTFORWARD 0x10F4
KEY_PLAY 0x10F5
KEY_RECORD 0x10F7
KEY_STOP 0x10F6
KEY_PAUSE 0x10F0
KEY_PREVIOUS 0x10E4
KEY_NEXT 0x10DE
end codes
end remote
/home/mythtv/.lircrc
# ~/.mythtv/lircrc # # MythTV native LIRC config file for # the new grey Hauppauge remote # # Modified from Jarod Wilson's which came from Jeff Campbell's # By Brad Templeton # Here we have the jump point commands. They only work if you have # defined function keys for these jump points. For me the most # common command is the menu of recordings, so I put that on "videos" # even though that's counter-intuitive begin prog = mythtv button = TV repeat = 2 config = F5 end begin prog = mythtv button = Videos repeat = 2 config = F2 end # Not yet defined begin prog = mythtv button = Music repeat = 2 config = Up end # Given another function for now, I don't use mythgallery begin prog = mythtv button = Pictures repeat = 2 config = F end begin prog = mythtv button = Guide repeat = 2 config = F3 end # I stuck the "todo" list on here as Myth has no radio function begin prog = mythtv button = Radio repeat = 2 config = F4 end begin prog = mythtv button = Up repeat = 1 config = Up end begin prog = mythtv button = Down repeat = 1 config = Down end begin prog = mythtv button = Left repeat = 1 config = Left end begin prog = mythtv button = Right repeat = 1 config = Right end # Channel Up begin prog = mythtv button = Ch+ repeat = 1 config = Up end # Channel Down begin prog = mythtv button = Ch- repeat = 1 config = Down end # OK/Select begin prog = mythtv button = Ok config = Space end # Play begin prog = mythtv button = Play config = Return end # Stop begin prog = mythtv button = Stop config = I end # Escape/Exit/Back begin prog = mythtv button = Back/Exit config = Esc end # Power Off/Exit begin prog = mythtv button = Power config = Esc end # Pause begin prog = mythtv button = Pause repeat = 2 config = P end # Mute begin prog = mythtv button = Mute repeat = 2 config = | end # Fast forward (30 sec default) begin prog = mythtv button = Rewind repeat = 2 config = < end # Rewind (10 sec default) begin prog = mythtv button = Forward repeat = 2 config = > end # Skip forward (10 min default) begin prog = mythtv button = SkipForward repeat = 2 config = End end # Skip backward (10 min default) begin prog = mythtv button = SkipBackward repeat = 2 config = Home end # Record begin prog = mythtv button = Record repeat = 2 config = R end # Delete begin prog = mythtv button = Red repeat = 2 config = D end # Decrease play speed begin prog = mythtv button = Green repeat = 2 config = J end # Display EPG while in live TV, # View selected show while in EPG begin prog = mythtv button = Menu/i repeat = 2 config = M end # Scroll up begin prog = mythtv button = Vol+ repeat = 2 config = F11 end # Scroll down begin prog = mythtv button = Vol- repeat = 2 config = F10 end # Bring up OSD info begin prog = mythtv button = Go repeat = 2 config = I end # Change display aspect ratio begin prog = mythtv button = Prev-Channel repeat = 2 config = W end # double speed watch begin prog = mythtv button = Yellow repeat = 2 config = J end # change tuners begin prog = mythtv button = hash repeat = 2 config = Y end # Bring up Time stretch begin prog = mythtv button = Blue repeat = 2 config = A end # Numbers 0-9 begin prog = mythtv button = 0 repeat = 2 config = 0 end begin prog = mythtv button = 1 repeat = 2 config = 1 end begin prog = mythtv button = 2 repeat = 2 config = 2 end begin prog = mythtv button = 3 repeat = 2 config = 3 end begin prog = mythtv button = 4 repeat = 2 config = 4 end begin prog = mythtv button = 5 repeat = 2 config = 5 end begin prog = mythtv button = 6 repeat = 2 config = 6 end begin prog = mythtv button = 7 repeat = 2 config = 7 end begin prog = mythtv button = 8 repeat = 2 config = 8 end begin prog = mythtv button = 9 repeat = 2 config = 9 end ### MPlayer lirc setup # Show OSD begin prog = mplayer button = MENU repeat = 2 config = osd end # Pause playback begin prog = mplayer button = PAUSE repeat = 2 config = pause end # Skip ahead a minute if playing # If paused, resume playing begin prog = mplayer button = PLAY repeat = 2 config = seek +1 end # Stop playback and exit begin prog = mplayer button = STOP repeat = 2 config = quit end # Mute begin prog = mplayer button = MUTE repeat = 2 config = mute end # Seek back 10 seconds begin prog = mplayer button = REW repeat = 2 config = seek -10 end # Seek forward 30 seconds begin prog = mplayer button = FFW repeat = 2 config = seek +30 end # Quit begin prog = mplayer button = BACK/EXIT repeat = 2 config = quit end # Seek forward 10 minutes begin prog = mplayer button = SKIP repeat = 2 config = seek +600 end # Seek backward 10 minutes begin prog = mplayer button = REPLAY repeat = 2 config = seek -600 end # Toggle full-screen begin prog = mplayer button = FULL repeat = 2 config = vo_fullscreen end ### Xine lirc setup begin prog = xine button = PLAY repeat = 2 config = Play end begin prog = xine button = STOP repeat = 2 config = Stop end begin prog = xine button = OFF repeat = 2 config = Quit end begin prog = xine button = PAUSE repeat = 2 config = Pause end begin prog = xine button = CH+ repeat = 2 config = EventUp end begin prog = xine button = CH- repeat = 2 config = EventDown end begin prog = xine button = VOL- repeat = 2 config = EventLeft end begin prog = xine button = VOL+ repeat = 2 config = EventRight end begin prog = xine button = OK repeat = 2 config = EventSelect end begin prog = xine button = BACK/EXIT repeat = 2 config = Menu end begin prog = xine button = FFW repeat = 2 #config = SpeedFaster config = SeekRelative+60 end begin prog = xine button = REW repeat = 2 #config = SpeedSlower config = SeekRelative-60 end begin prog = xine button = FULL repeat = 2 config = Volume+ end begin prog = xine button = BLANK repeat = 2 config = Volume- end begin prog = xine button = MUTE repeat = 2 config = Mute end begin prog = xine button = MENU repeat = 2 config = RootMenu end begin prog = xine button = SKIP repeat = 2 config = EventNext end begin prog = xine button = REPLAY repeat = 2 config = EventPrior end begin prog = xine button = GO repeat = 2 config = OSDStreamInfos end begin prog = xine button = RED repeat = 2 config = Quit end begin prog = xine button = RED repeat = 2 config = Quit end
My Backup script
date= date -I nice -n 19 mysqldump -u root --password=testers --extended-insert --no-create-db --add-drop-table --database mythconverg > `date -I`_myth_backup_data.sql nice -n 19 mysqldump -u root --password=testers --extended-insert --database mythconverg > `date -I`_myth_complete_backup_data.sql nice -n 19 gzip `date -I`_myth_backup_data.sql nice -n 19 gzip `date -I`_myth_complete_backup_data.sql chmod 777 `date -I`_myth_backup_data.sql.gz chmod 777 `date -I`_myth_complete_backup_data.sql.gz mv `date -I`_myth_backup_data.sql.gz /storage1/Database/ mv `date -I`_myth_complete_backup_data.sql.gz /storage1/Database/
My Restore
mysql -u root -p < myth_complete_backup_data.sql
Setting Atrpms.repo
[atrpms] name=Fedora Core $releasever - $basearch - ATrpms baseurl=http://dl.atrpms.net/f$releasever-$basearch/atrpms/stable gpgkey=http://ATrpms.net/RPM-GPG-KEY.atrpms enabled=1 gpgcheck=1
Setting up Autologin
/etc/gdm/custom # GDM configuration storage [daemon] TimedLoginEnable=true TimedLogin=mythtv TimedLoginDelay=5 [security] [xdmcp] [greeter] [chooser] [debug]
Crontab
* 3 * * * /home/mythtv/backup-mysql.sh * 4 1 * * /home/mythtv/optimize-myth-db.sh
/etc/init.d/mythbackend
#!/bin/bash
#
# Rename this file to:
#
# /etc/rc.d/init.d/mythbackend
#
###############################################################################
#
# chkconfig: - 86 14
# pidfile: /var/run/mythbackend.pid
# description: Starts the mythbackend process as a daemon after X and MySQL \
# have started, in runlevel 5. This allows scheduled recordings \
# to occur without manual intervention.
# processname: mythbackend
# config: /etc/sysconfig/mythbackend
#
###############################################################################
#
# Copyright (c) by the MythTV Development Team.
#
# Derived from work by:
#
# Michael Thomson <linux at m-thomson dot net>
# Stu Tomlinson <stu at nosnilmot dot com>
# Axel Thimm <axel.thimm at atrpms dot net>
#
# This program is free software; you can redistribute it and/or modify
# it under the terms of the GNU General Public License as published by
# the Free Software Foundation; either version 2 of the License, or
# (at your option) any later version.
#
# This program is distributed in the hope that it will be useful,
# but WITHOUT ANY WARRANTY; without even the implied warranty of
# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
# GNU General Public License for more details.
#
# You should have received a copy of the GNU General Public License
# along with this program; if not, write to the Free Software
# Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA
#
###############################################################################
# Default values to use if none are supplied in the config file.
# Running mythbackend as non-root requires you to ensure that audio/video
# devices used for recording have suitable user permissions. One way
# to achieve this is to modify existing or create new udev rules which
# assign these devices to a non-root group with rw permissions and add
# your mythbackend user to that group. Be aware that console.perms can
# also affect device permissions and may need additional configuration.
# Running as non-root may also introduce increased process latency.
#
# User who should start the mythbackend processes
MBE_USER='root'
# Directory holding the mythbackend binary (empty means autodetect)
MBE_DIR=
# Name of mythbackend binary
MBE_PROG='mythbackend'
# Startup options for mythbackend
MBE_OPTIONS=
# Directory holding the mythbackend log file
LOG_DIR='/var/log/mythtv'
# Name of mythbackend log file
LOG_FILE='mythbackend.log'
# Logging options for mythbackend (empty means '-v important,general')
LOG_OPTS=
###############################################################################
# Source function library.
. /etc/init.d/functions
# Source config file if available
if [ -f "/etc/sysconfig/mythbackend" ]; then
. /etc/sysconfig/mythbackend
fi
# Find the executable
if [ ! -z "$MBE_DIR" ]; then
MBE_BIN="$MBE_DIR/$MBE_PROG"
else
MBE_BIN=`which "$MBE_PROG" 2>/dev/null`
if [ ! -f "$MBE_BIN" ]; then
if [ -f "/usr/bin/$MBE_PROG" ]; then
MBE_BIN="/usr/bin/$MBE_PROG"
elif [ -f "/usr/local/bin/$MBE_PROG" ]; then
MBE_BIN="/usr/local/bin/$MBE_PROG"
fi
fi
fi
# Error messages
if [ ! -f "$MBE_BIN" ]; then
echo "Cannot find $MBE_PROG executable"
exit 1
elif [ ! -x "$MBE_BIN" ]; then
echo "$MBE_PROG is not executable"
exit 1
elif [ ! -d "$LOG_DIR" ]; then
echo "Log directory does not exist"
exit 1
fi
# Initialize the return variable
RETVAL=0
##############################################################################
#
# Start the process
#
start() {
# Already running?
if [ -f "/var/lock/subsys/$MBE_PROG" ]; then
echo "$MBE_PROG is already running."
return 0
fi
# Start
echo -n $"Starting $MBE_PROG: "
touch "/var/run/$MBE_PROG.pid"
chown "$MBE_USER":"$MBE_USER" "/var/run/$MBE_PROG.pid"
daemon --user "$MBE_USER" "$MBE_BIN" \
--daemon \
--logfile "$LOG_DIR/$LOG_FILE" "$LOG_OPTS" \
--pidfile "/var/run/$MBE_PROG.pid" \
$MBE_OPTIONS
RETVAL=$?
[ $RETVAL = 0 ] && touch /var/lock/subsys/$MBE_PROG
echo
return $RETVAL
}
#
# Stop the process
#
stop() {
echo -n $"Stopping $MBE_PROG: "
killproc "$MBE_PROG"
RETVAL=$?
[ $RETVAL -eq 0 ] && rm -f /var/lock/subsys/${MBE_PROG} /var/run/${MBE_PROG}.pid
echo
return $RETVAL
}
#
# Restart
#
restart() {
stop
start
}
###############################################################################
case "$1" in
start)
start
;;
stop)
stop
;;
restart)
restart
;;
condrestart)
if [ -f "/var/lock/subsys/$MBE_PROG" ]; then
restart
fi
;;
status)
status "$MBE_BIN"
RETVAL=$?
;;
*)
echo "Usage: $0 {start|stop|restart|condrestart|status}"
exit 1
esac
exit $RETVAL
/etc/init.d/mythjobqueue
#!/bin/bash
#
# Rename this file to:
#
# /etc/rc.d/init.d/mythjobqueue
#
###############################################################################
#
# chkconfig: - 86 14
# pidfile: /var/run/mythjobqueue.pid
# description: Starts the mythjobqueue process as a daemon after X and MySQL \
# have started, in runlevel 5. This allows jobs to be processed \
# without manual intervention.
# processname: mythjobqueue
# config: /etc/sysconfig/mythjobqueue
#
###############################################################################
#
# Copyright (c) by the MythTV Development Team.
#
# Derived from work by:
#
# Michael Thomson <linux at m-thomson dot net>
# Stu Tomlinson <stu at nosnilmot dot com>
# Axel Thimm <axel.thimm at atrpms dot net>
#
# This program is free software; you can redistribute it and/or modify
# it under the terms of the GNU General Public License as published by
# the Free Software Foundation; either version 2 of the License, or
# (at your option) any later version.
#
# This program is distributed in the hope that it will be useful,
# but WITHOUT ANY WARRANTY; without even the implied warranty of
# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
# GNU General Public License for more details.
#
# You should have received a copy of the GNU General Public License
# along with this program; if not, write to the Free Software
# Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA
#
###############################################################################
# Default values to use if none are supplied in the config file.
# Running mythjobqueue as non-root may require you to ensure that the
# recording directories and files have suitable user permissions. If
# all recording file access is done via streaming from the backends,
# this is not necessary.
#
# User who should start the mythjobqueue processes
MBE_USER='root'
# Directory holding the mythjobqueue binary (empty means autodetect)
MBE_DIR=
# Name of mythjobqueue binary
MBE_PROG='mythjobqueue'
# Startup options for mythjobqueue
MBE_OPTIONS=
# Directory holding the mythjobqueue log file
LOG_DIR='/var/log/mythtv'
# Name of mythjobqueue log file
LOG_FILE='mythjobqueue.log'
# Logging options for mythjobqueue (empty means '-v important,general')
LOG_OPTS=
###############################################################################
# Source function library.
. /etc/init.d/functions
# Source config file if available
if [ -f "/etc/sysconfig/mythjobqueue" ]; then
. /etc/sysconfig/mythjobqueue
fi
# Find the executable
if [ ! -z "$MBE_DIR" ]; then
MBE_BIN="$MBE_DIR/$MBE_PROG"
else
MBE_BIN=`which "$MBE_PROG" 2>/dev/null`
if [ ! -f "$MBE_BIN" ]; then
if [ -f "/usr/bin/$MBE_PROG" ]; then
MBE_BIN="/usr/bin/$MBE_PROG"
elif [ -f "/usr/local/bin/$MBE_PROG" ]; then
MBE_BIN="/usr/local/bin/$MBE_PROG"
fi
fi
fi
# Error messages
if [ ! -f "$MBE_BIN" ]; then
echo "Cannot find $MBE_PROG executable"
exit 1
elif [ ! -x "$MBE_BIN" ]; then
echo "$MBE_PROG is not executable"
exit 1
elif [ ! -d "$LOG_DIR" ]; then
echo "Log directory does not exist"
exit 1
fi
# Initialize the return variable
RETVAL=0
###############################################################################
#
# Start the process
#
start() {
# Already running?
if [ -f "/var/lock/subsys/$MBE_PROG" ]; then
echo "$MBE_PROG is already running."
return 0
fi
# Start
echo -n $"Starting $MBE_PROG: "
touch "/var/run/$MBE_PROG.pid"
chown "$MBE_USER":"$MBE_USER" "/var/run/$MBE_PROG.pid"
daemon --user "$MBE_USER" "$MBE_BIN" \
--daemon \
--logfile "$LOG_DIR/$LOG_FILE" "$LOG_OPTS" \
--pidfile "/var/run/$MBE_PROG.pid" \
$MBE_OPTIONS
RETVAL=$?
[ $RETVAL = 0 ] && touch /var/lock/subsys/$MBE_PROG
echo
return $RETVAL
}
#
# Stop the process
#
stop() {
echo -n $"Stopping $MBE_PROG: "
killproc "$MBE_PROG"
RETVAL=$?
[ $RETVAL -eq 0 ] && rm -f /var/lock/subsys/${MBE_PROG} /var/run/${MBE_PROG}.pid
echo
return $RETVAL
}
#
# Restart
#
restart() {
stop
start
}
###############################################################################
case "$1" in
start)
start
;;
stop)
stop
;;
restart)
restart
;;
condrestart)
if [ -f "/var/lock/subsys/$MBE_PROG" ]; then
restart
fi
;;
status)
status "$MBE_BIN"
RETVAL=$?
;;
*)
echo "Usage: $0 {start|stop|restart|condrestart|status}"
exit 1
esac
exit $RETVAL
Mythtv->Setup-General
LIRC daemon socket /var/run/lirc/lircd
Notes on Fedora 15 Install
Using the default nouveau video driver GeForce 6200 SVideo
Add boot option to grub.conf nouveau.tv_norm=NTSC-M
kernel /vmlinuz-2.6.40.6-0.fc15.x86_64 ro root=UUID=4b78f456-a78b-4f2b-b4b6-392bd5a2b215 rd_NO_LUKS rd_NO_LVM rd_NO_MD rd_NO_DM LANG=en_US.UTF-8 SYSFONT=latarcyrheb-sun16 KEYTABLE=us nouveau.tv_norm=NTSC-M quiet initrd /initramfs-2.6.40.6-0.fc15.x86_64.img
Installing MS Core Fonts
yum install rpm-build cabextract ttmkfdir wget wget http://corefonts.sourceforge.net/msttcorefonts-2.0-1.spec rpmbuild -ba msttcorefonts-2.0-1.spec yum install --nogpgcheck /root/rpmbuild/RPMS/noarch/msttcorefonts-2.0-1.noarch.rpm
