High Definition Disk Formats
It is possible to play back Hi-Def media such as Blu-ray and HD-DVD Disks in MythTV. While it is currently impossible to place a HD-DVD disk in the drive and play it with MythTV, one can rip the files onto the hard drive and play them with the internal player. Blu-ray playback of some material directly from the disc and as a folder structure on a hard drive is possible. Please note the following caveats before following this guide:
- Decrypting copy-protected media may be illegal where you live. Take note of any local laws concerning the circumvention of copy-protection and act accordingly.
- Playback of 1080p content is extremely processor-intensive unless you use hardware acceleration such as VDPAU. Many users download 1080p content from the internet that has been transcoded and downsampled to very low bitrates. True HD-DVD and Blu-ray rips average between two and four times higher bitrates. These files are therefore substantially more difficult to play. The advantage to this method is that the quality is vastly superior when viewing an untranscoded rip.
- This guide is written for use with Ubuntu, but there is very little within that cannot be directly applied to any other distribution.
- Menus and other interactive content are currently unavailable in Linux. The user will only be able to play the video files on the disk.
- Some blu-ray disks with BD+ encryption can now be ripped under linux. There are Windows alternatives that are able to offer more comprehensive BD+ ripping support. One option is SlySoft AnyDVD HD, which rips both HD-DVD and Blu-ray disk formats.
Understanding HD-DVD and Blu-ray structure
Blu-ray and HD-DVD are fundamentally the same creature from a linux perspective. Both contain muxed files using either the MPEG-4 Part 10 (H.264), VC1, or MPEG-2 codecs, and audio tracks in AC-3, E-AC3, DTSHD, TrueHD, or MLP audio formats. HD-DVD uses the EVO container which is analogous to a VOB file in DVD parlance. Blu-Ray uses M2TS, or MPEG-2 Transport Stream containers. The video formats on both disk types are well understood and have various levels of support in FFmpeg.
Blu-Ray features are generally found in a collection of .m2ts files, while HD-DVD features are usually two or more EVO files (Usually the two largest on the disk and sequentially numbered, ie FEATURE_1.EVO and FEATURE_2.EVO).
Ripping Hi-Definition Media
To rip Hi-Def Media to the disk with DumpHD, you will need all of the following:
- A drive capable of playing back the media you intend to rip (ie the Xbox 360 HD-DVD Drive or the LG GGC-H20L HD-DVD/Blu-ray Combo Drive)
- Adequate disk space for the entire movie, generally between 25-50 GB/disk. After removing extras and menus, this is commonly 20-30 GB/movie.
- A Kernel with UDF 2.5 Support (Most current distros as of 2009 ship with this)
- Begin by downloading DumpHD, available at the Doom9 Forums. Navigate to the directory where you downloaded the file and untar it:
tar xvzf dumphd-0.6.tar.gz
- Download the current copy of libAACS. Navigate to the directory where you downloaded the file and untar it:
tar xvzf aacskeys-0.4.0.tar.gz
- Enter the aacskeys directory:
- Build the aacs source:
- Copy the ProcessingDeviceKeysSimple.txt to the DumpHD directory:
cp ProcessingDeviceKeysSimple.txt ~/dumphd-0.6/
- Enter the DumpHD lib directory and copy the appropriate version of libaacskeys.so to the DumpHD directory. If you are on 32 bit Linux, this will be lib/linux32 from within the aacskeys source. If you are on 64 bit Linux, this will be lib/linux64 from within the aacskeys source. Example:
cd lib/linux64 && cp libaacskeys.so ~/dumphd-0.6/
- Start DumpHD and insert the HD-DVD or Blu-ray Disk into your drive.
cd dumphd_0.6 && bash dumphd.sh
- Click "Browse" in the upper right and navigate to your disk (ie, /media/300_HDDVD) and select it as the source.
- Click "Browse" in the section marked "Destination" to select the directory in which to copy the files (ie, /tmp).
- Click "Dump" to begin ripping the disk.
- Optional Step: If the feature is composed of multiple files, you can append the files with the cat command.
cat FEATURE_1.EVO FEATURE_2.EVO > outfile.evo
Erase any extra files. Only the feature film is necessary for playback.
Note! The above instructions pertain only to AACS protected disks. BD+ decryption is still in its infancy. More information to follow.
MakeMKV offers a way to stream or to store BD and BD+ discs on your network
- Install prerequisites
sudo apt-get install build-essential libc6-dev libssl-dev libgl1-mesa-dev libqt4-dev
- Get binary files
- Get source files
- Unpack archives
tar -xvf makemkv_v1.4.11_beta_bin.tar.gz && tar -xvf makemkv_v1.4.11_beta_oss.tar.gz
- cd into each source directory and run the following two steps
make -f makefile.linux
sudo make -f makefile.linux install
- Run the application /usr/bin/makemkv
- Go to File, Open Disc > Select your Blu-Ray drive
- Once MakeMKV finishes opening the blu-ray disc, it will list the titles and file information
- Go to File menu and choose "Stream"
- MakeMKV will look like "Buffer State" and "File Position" are stuck, but look in the dialog box at the beginning for something similar to: "Operation sucessfully completed. Streaming server started, web server address is..."
To connect and watch
- Open VLC and go to Media, Open Network Stream
- Protocol should HTTP, in the address box put http://localhost:51000/stream/title0.ts The port option should be greyed out.
- Click Play and enjoy your blu-ray movies within Linux
Firmware Patching to get Volume ID
If you happen to own a Plextor PX-B920SA / LG GGW-H20*/ LG GGC-H20* optical drive and have issues with revoked player keys, fear not, a firmware patch for your drive is available that will cause the drive to report the Volume ID needed to decrypt the disc regardless. You can find links to the altered firmware on Doom9.
You can also run the Windows tool AnyDVD HD in a VMWare or VirtualBox instance. AnyDVD HD will *not* work in Wine. In VMWare, you can rip the files wherever you like, then copy them to your MythVideo share via Samba.
AnyDVD is by far the most capable Blu-ray and HD-DVD ripping software available. Whereas DumpHD is limited to the AACS keys in the downloaded file, AnyDVD HD can rip any AACS encrypted disk. It can also rip all known BD+ encrypted disks. Almost all new disks are encrypted with BD+, making AnyDVD the only software capable of ripping them. It is available for purchase from SlySoft.
Playing Hi-Definition Material
Watching With the Internal Player (recommended)
With TrueHD/MLP and E-AC-3 support in ffmpeg, Myth has gained full out-of-the-box support of playback for these files as of version 0.22. As of MythTV .24, the internal player is capable of playing Blu-ray disc structures both directly from the disc and from the folder structure on a hard drive.
MythTV 0.25 or trunk from December 10th 2010, supports bitstreaming of E-AC3, DTS-HD High-Res, TrueHD and DTS-HD MA. Check the HD Audio Passthrough page on how to get it going.
The minimum requirements are:
- MythTV .24 or later
- A Blu-ray drive
- A disc protected by AACS MKB version 10 or lower, and not protected by BD+
- libAACS compiled, installed, and functional. It does not need to be present at MythTV compile time.
- A properly configured KEYDB.cfg located at ~/.mythtv/KEYDB.cfg (see the libAACS thread above for instructions on how to properly edit the file)
- You will probably want some information contained in aacskeys
Straight from the disc playback is only possible from the command line, simply because nobody has added a menu entry to launch BD playback (having multiple menu items to launch each type of disc is messy and the desire is to unify them all under a single menu item). However, if all of the above is met, you can insert a disk and launch it by pointing mythavtest at its mount point, eg:
If the disk does not play, you can increase the verbosity of the decryption libraries by prefacing the command with BD_DEBUG_MASK=8, example:
BD_DEBUG_MASK=8 mythavtest bd://media/cdrom0
Watching With External Players
Mplayer and FFmpeg now include support for the MLP/TrueHD, DTS-HD MA, and E-AC3 audio codecs in SVN, and require no patching for this material. It is advisable to compile both, as ffmpeg will make it easier to determine what type of audio tracks are available.
Once you have patched, compiled, and installed mplayer as appropriate, you need to edit the codecs.conf file in your ~/.mplayer/ directory. There may be a copy you can edit and copy in /etc/mplayer. Insert the following into the existing codecs.conf file:
audiocodec mlp info "FFMpeg mlp" status buggy format 0x20504C4D driver ffmpeg dll "mlp"
At this point, it is possible to play back your film. If you patched and compiled FFMpeg, use it to inspect your film (In this case a rip of the "300" HD-DVD). The format is "ffmpeg -i filename".
root@mythtv:~# ffmpeg -i /movies/300.EVO FFmpeg version SVN-r11584, Copyright (c) 2000-2008 Fabrice Bellard, et al. configuration: --prefix=/usr --enable-shared --enable-gpl --enable-pp --enable-swscaler --enable-pthreads --enable-liba52 --enable-liba52bin --enable-libfaac --enable-libfaad --enable-libfaadbin --enable-libgsm --enable-libmp3lame --enable-libtheora --enable-libvorbis --enable-libx264 --enable-libxvid libavutil version: 49.6.0 libavcodec version: 51.49.0 libavformat version: 52.5.0 libavdevice version: 52.0.0 built on Jan 20 2008 18:24:00, gcc: 4.1.3 20070929 (prerelease) (Ubuntu 4.1.2-16ubuntu2) Input #0, mpeg, from '/movies/300.EVO': Duration: 01:56:32.5, start: 20523.753856, bitrate: 22580 kb/s Stream #0.0[0xfd55]: Video: vc1, yuv420p, 1920x1080 [PAR 1:1 DAR 16:9], 29.97 tb(r) Stream #0.1[0xfd56]: Video: vc1, yuv420p, 720x480 [PAR 40:33 DAR 20:11], 29.97 tb(r) Stream #0.2[0xc4]: Audio: liba52, 48000 Hz, stereo, 192 kb/s Stream #0.3[0xc3]: Audio: liba52, 48000 Hz, 5:1, 640 kb/s Stream #0.4[0xb1]: Audio: mlp, 48000 Hz, 5:1 Stream #0.5[0xc2]: Audio: liba52, 48000 Hz, 5:1, 640 kb/s Stream #0.6[0xc0]: Audio: liba52, 48000 Hz, 5:1, 640 kb/sOn movies with MLP audio tracks, it is best to use it rather than the liba52 tracks (these tracks can be either E-AC-3 or AC-3). In order to play the film, you must specify the demuxer, the audio codec, the audio ID, and the frame rate. For all HD-DVD movies, the demuxer will remain the same. The other options will change. With newer versions of mplayer (i.e. SVN-29134), you may need to add
-lavfdopts format=mpegto the command line when playing back EVO files.
On this rip of 300 HD-DVD, the correct command line is:
mplayer -fs -vo xv -demuxer lavf -ac mlp -aid 4 -fps 24000/1001 /movies/300.EVO
Note: If -ac mlp does not work on your system, try -ac ffmlp.
This command line invokes MPlayer in full screen mode with Xv output, sets the demuxer to lavf, the audio codec to MLP, the audio track number to 4 (derived from the ffmpeg output, "Stream #0.4"), and the frame rate to 23.97. To play back one of the E-AC3 tracks in the same file, use a command like this:
mplayer -fs -vo xv -demuxer lavf -ac ffac3 -aid 3 -fps 24000/1001 /movies/300.EVO
Note: If -ac ffac3 does not work on your system, try -ac ffeac3.Many Blu-Ray movies can follow the '300' HD-DVD example above, but sometimes mplayer has trouble finding the correct audio track using the lavf demuxer. If you have problems, try using
-demuxer mpegtsinstead. Sometimes mpegts does a better job at seeing the main audio track.
If you experience slow playback, try the following options:
-lavdopts threads=2:fast:skiploopfilter=all -sws 0 -framedrop
This will remove all processing of the file and play back multithreaded if possible.
If the playback works properly, copy the file into your MythTV video directory. Enter the Video Manager in MythTV's frontend. Select the film from the list and press the right arrow. Select "Edit Metadata." The last option is to set a custom player command for the file. Paste or type the command you used into the box and press "Done." The file should now play back as any other in MythVideo.