Modeline Database

From MythTV Official Wiki
Revision as of 11:46, 25 April 2008 by Ldkronos (talk | contribs) (Sharp)

Jump to: navigation, search

Important.png Note: Modelines are not used by recent Nvidia and Intel drivers when using the TV-Out ability of these chipsets. Instead they use an internal list of valid modes.


Important.png Note: Newer Nvidia drivers will not accept hyphen "-" characters in mode names. Change any mode names containing hyphens to underscores in order to avoid errors and potentially, hours of frustration!

Database of standard modelines as well as user created modelines for specific HD Televisions.

Contents

Standard Modelines

An on-line modeline calculation tool is available at: http://www.tkk.fi/Misc/Electronics/faq/vga2rgb/calc.html.

NVIDIA Driver ModePool

Versions of the Nvidia driver from the 8xxx series upwards use a built in list of modelines. You just have to set the correct modes for your display in the Screen subsection.

The format is simple, HorizontalResolutionxVerticalResolution_frequency

So the following line in your Screen subsection for your TV,

    Modes      "1920x1080_60" "1280x720_60" "720x480_60"

would yield 1080p, 720p and 480p outputs

    Modes      "1920x1080_60i"

would yield 1080i output.

These should be compliant for DVI and component output on all TV's so its probably worth trying before playing around with EDID and custom modelines.

50hz vertical refresh

if you are using anything other than 60hz you will need to enable this. Add this option to the "Screen" section of your xorg.conf

Option "ModeValidation" "AllowNon60HzDFPModes"

ModeValidation

Some HDTV and monitors connected via VGA or DVI in which your able to receive EDID information may need to enable some options from the ModeValidation option, as you can see below. Be careful in using these, some may cause your TV/monitor problems, so use them sparingly! Figure out which options you absolutely need.

From the NVIDIA readme,

Option "ModeValidation" "string"

This option provides fine-grained control over each stage of the mode 
validation pipeline, disabling individual mode validation checks. This
option should only very rarely be used.

The option string is a semicolon-separated list of comma-separated lists
of mode validation arguments. Each list of mode validation arguments can
optionally be prepended with a display device name.

"<dpy-0>: <tok>, <tok>; <dpy-1>: <tok>, <tok>, <tok>; ..."

Possible arguments:

"AllowNon60HzDFPModes": some lower quality TMDS encoders are only rated 
to drive DFPs at 60Hz; the driver will determine when only 60Hz DFP modes 
are allowed. This argument disables this stage of the mode validation pipeline.

"NoMaxPClkCheck": each mode has a pixel clock; this pixel clock is validated 
against the maximum pixel clock of the hardware (for a DFP, this is the 
maximum pixel clock of the TMDS encoder, for a CRT, this is the maximum pixel 
clock of the DAC). This argument disables the maximum pixel clock checking 
stage of the mode validation pipeline.

"NoEdidMaxPClkCheck": a display device's EDID can specify the maximum pixel 
clock that the display device supports; a mode's pixel clock is validated 
against this pixel clock maximum. This argument disables this stage of the mode 
validation pipeline.

"AllowInterlacedModes": interlaced modes are not supported on all NVIDIA GPUs; 
the driver will discard interlaced modes on GPUs where interlaced modes are 
not supported; this argument disables this stage of the mode validation pipeline.

"NoMaxSizeCheck": each NVIDIA GPU has a maximum resolution that it can drive; 
this argument disables this stage of the mode validation pipeline.

"NoHorizSyncCheck": a mode's horizontal sync is validated against the range 
of valid horizontal sync values; this argument disables this stage of the mode 
validation pipeline.

"NoVertRefreshCheck": a mode's vertical refresh rate is validated against the
range of valid vertical refresh rate values; this argument disables this stage 
of the mode validation pipeline.

"NoWidthAlignmentCheck": the alignment of a mode's visible width is validated 
against the capabilities of the GPU; normally, a mode's visible width must be 
a multiple of 8. This argument disables this stage of the mode validation pipeline.

"NoDFPNativeResolutionCheck": when validating for a DFP, a mode's size is 
validated against the native resolution of the DFP; this argument disables this 
stage of the mode validation pipeline.

"NoVirtualSizeCheck": if the X configuration file requests a specific virtual 
screen size, a mode cannot be larger than that virtual size; this argument disables 
this stage of the mode validation pipeline.

"NoVesaModes": when constructing the mode pool for a display device, the X driver 
uses a built-in list of VESA modes as one of the mode sources; this argument 
disables use of these built-in VESA modes.

"NoEdidModes": when constructing the mode pool for a display device, the X driver 
uses any modes listed in the display device's EDID as one of the mode sources; 
this argument disables use of EDID-specified modes.

"NoXServerModes": when constructing the mode pool for a display device, the X 
driver uses the built-in modes provided by the core XFree86/Xorg X server as one 
of the mode sources; this argument disables use of these modes. Note that this 
argument does not disable custom ModeLines specified in the X config file; see 
the "NoCustomModes" argument for that.

"NoCustomModes": when constructing the mode pool for a display device, the X 
driver uses custom ModeLines specified in the X config file (through the "Mode" 
or "ModeLine" entries in the Monitor Section) as one of the mode sources; this 
argument disables use of these modes.

"NoPredefinedModes": when constructing the mode pool for a display device, the
X driver uses additional modes predefined by the NVIDIA X driver; this argument
disables use of these modes.

"NoUserModes": additional modes can be added to the mode pool dynamically, using
the NV-CONTROL X extension; this argument prohibits user-specified modes via the
NV-CONTROL X extension.

NTSC (Analog)

#Analog-RegularModes
#ModeLine "NTSCspec-59.94i" 14.318 768 784 848 910 483 484 492 525 Interlace
#ModeLine "NTSCspec-59.94p" 28.636 768 784 848 910 483 484 492 525
#ModeLine "Laserdisk-59.94i" 567 583 647 684 483 484 492 525 Interlace
#ModeLine "Laserdisk-59.94p" 567 583 647 684 483 484 492 525
#ModeLine "Broadcast-59.94i" 483 484 492 525 Interlace
#ModeLine "Broadcast-59.94p" 483 484 492 525
#ModeLine "VHS-59.94i" 483 484 492 525 Interlace
#ModeLine "VHS-59.94p" 483 484 492 525

Note: Some of these NTSC modelines are invalid. A modeline needs 9 numbers. Putting "Broadcast-59.94i" in my XF86Config-4 broke X windows.

PAL 625

# 702x576 @ 25Hz, 15.6kHz hsync, itu-r bt.470 PAL, analog broadcast
ModeLine "702x576@25i" 13.5   702 722 785 864  576 581 586 625 interlace -hsync -vsync

# 704x576 @ 25Hz, 15.6kHz hsync, itu-r bt.470 PAL, mpeg, 702 dots displayed
ModeLine "704x576@25i" 13.5   704 723 786 864  576 581 586 625 interlace -hsync -vsync

# 720x576 @ 25Hz, 15.6kHz hsync, ccir601 PAL, mpeg, 702 dots displayed
ModeLine "720x576@25i" 13.5   720 732 795 864  576 581 586 625 interlace -hsync -vsync

# 768x576 @ 25Hz, 15.6kHz hsync, square dot itu-r bt.470 PAL, TV-monitor, 767 dots displayed
ModeLine "768x576@25i" 14.75  768 789 858 944  576 581 586 625 interlace -hsync -vsync

# 768x576 @ 50Hz, 31.3kHz hsync, progressive square dot itu-r bt.470 PAL 
ModeLine "768x576@50"  29.5   768 789 858 944  576 581 586 625 -hsync -vsync

# nonstandard PAL (Works with BOB deinterlace) It is 60Hz but works well with nVIDIA PAL-B TV-OUT
# Nvidia option: Option "TVStandard" "PAL-B"
ModeLine "720x576@60" 32.7  720 744 816 912  576 577 580 597

# This modeline is 50Hz interlaced and works well with kerneldeint:
ModeLine "720x576i" 13.875  720 744 808 888  576 581 586 625 -hsync -vsync interlace

Note: PAL 625 broadcast equipment using a 13.5 MHz reference frequency sets the image aspect ratio of 704x576 to 1.33=4/3 and of 720x576 to 1.3636=15/11. This ensures compatibility with analog TV's which expect 702x575 at a ratio of 4/3. Video monitors can display the whole image, including the extra dots on the left and right, by depressing the underscan switch. Analog broadcast cameras typically output a 14.75 MHz square dot resolution of 786x581 from a 816x606 CCD frame.

DVD

#DVD-NativeModes
#ModeLine "NTSC-DVD-59.94i" 13.5 720 736 800 858 480 484 492 525 Interlace
#ModeLine "NTSC-DVD-60i" 13.514 720 736 800 858 480 484 492 525 Interlace
#ModeLine "NTSC-DVD-59.94p" 27.0 720 736 800 858 480 484 492 525
#ModeLine "NTSC-DVD-60p" 27.027 720 736 800 858 480 484 492 525
#ModeLine "NTSC-DVD-71.93p" 32.4 720 736 800 858 480 484 492 525
#ModeLine "NTSC-DVD-72p" 32.432 720 736 800 858 480 484 492 525
#ModeLine "NTSC-DVD-119.88p" 54.0 720 736 800 858 480 484 492 525
#ModeLine "NTSC-DVD-120p" 54.054 720 736 800 858 480 484 492 525

DILA Projector Native

#DILA-Projector-NativeModes
#ModeLine "DILA-47.95p" 91.493 1360 1464 1608 1800 1024 1026 1028 1060
#ModeLine "DILA-48p" 91.584 1360 1464 1608 1800 1024 1026 1028 1060
#ModeLine "DILA-50p" 95.4 1360 1464 1608 1800 1024 1026 1028 1060
#ModeLine "DILA-59.94p" 114.366 1360 1464 1608 1800 1024 1026 1028 1060
#ModeLine "DILA-60p" 114.48 1360 1464 1608 1800 1024 1026 1028 1060
#ModeLine "DILA-71.93p" 137.239 1360 1464 1608 1800 1024 1026 1028 1060
#ModeLine "DILA-72p" 137.376 1360 1464 1608 1800 1024 1026 1028 1060
#ModeLine "DILA-MarkR-71.997" 139.202 1360 1464 1608 1824 1024 1026 1028 1060

ATSC Standard Modes

#DTV-StandardModes
#ModeLine "ATSC-480-59.94i" 11.958 640 664 736 760 480 484 492 525 Interlace
#ModeLine "ATSC-480-60i" 11.97 640 664 736 760 480 484 492 525 Interlace
#ModeLine "ATSC-480-59.94p" 23.916 640 664 736 760 480 484 492 525
#ModeLine "ATSC-480-60p" 23.94 640 664 736 760 480 484 492 525
#ModeLine "ATSC-480a-59.94i" 11.958 640 664 736 760 480 484 492 525 Interlace
#ModeLine "ATSC-480a-60i" 11.97 640 664 736 760 480 484 492 525 Interlace
#ModeLine "ATSC-480a-59.94p" 23.916 640 664 736 760 480 484 492 525
#ModeLine "ATSC-480a-60p" 23.94 640 664 736 760 480 484 492 525
#ModeLine "ATSC-720-59.94p" 74.176 1280 1320 1376 1650 720 722 728 750
#ModeLine "ATSC-720-60p" 74.25 1280 1320 1376 1650 720 722 728 750
#ModeLine "ATSC-1080-59.94i" 74.176 1920 1960 2016 2200 1080 1082 1088 1125 Interlace
#ModeLine "ATSC-1080-60i" 74.25 1920 1960 2016 2200 1080 1082 1088 1125 Interlace
#ModeLine "ATSC-1080-59.94p" 148.352 1920 1960 2016 2200 1080 1082 1088 1125
#ModeLine "ATSC-1080-60p" 148.5 1920 1960 2016 2200 1080 1082 1088 1125

ATSC Movie Modes

#DTV-MovieModes
#ModeLine "ATSC-480-71.93p" 28.699 640 664 736 760 480 484 492 525
#ModeLine "ATSC-480-72p" 28.728 640 664 736 760 480 484 492 525
#ModeLine "ATSC-480-119.88p" 47.832 640 664 736 760 480 484 492 525
#ModeLine "ATSC-480-120p" 47.88 640 664 736 760 480 484 492 525
#ModeLine "ATSC-720-71.93p" 89.011 1280 1296 1360 1650 720 722 728 750
#ModeLine "ATSC-720-72p" 89.1 1280 1296 1360 1650 720 722 728 750
#ModeLine "ATSC-720-119.88p" 148.351 1280 1296 1360 1650 720 722 728 750
#ModeLine "ATSC-720-120p" 148.5 1280 1296 1360 1650 720 722 728 750
#ModeLine "ATSC-1080-71.93i" 1920 1960 2016 2200 1080 1082 1088 1125 Interlace
#ModeLine "ATSC-1080-72i" 1920 1960 2016 2200 1080 1082 1088 1125 Interlace
#ModeLine "ATSC-1080-71.93p" 178.022 1920 1960 2016 2200 1080 1082 1088 1125
#ModeLine "ATSC-1080-72p" 178.2 1920 1960 2016 2200 1080 1082 1088 1125

PC Tweaked

#DTV-PCTweakedModes
#ModeLine "NTSC-59.94i" 14.35 768 808 864 912 483 485 491 525 Interlace
#ModeLine "NTSC-59.94p" 28.699 768 808 864 912 483 485 491 525
#ModeLine "NTSC-DVD-59.94i" 13.469 720 760 816 856 480 482 488 525 Interlace
#ModeLine "NTSC-DVD-60i" 13.482 720 760 816 856 480 482 488 525 Interlace
#ModeLine "NTSC-DVD-59.94p" 26.937 720 760 816 856 480 482 488 525
#ModeLine "NTSC-DVD-60p" 26.964 720 760 816 856 480 482 488 525
#ModeLine "NTSC-DVD-71.93p" 32.324 720 760 816 856 480 482 488 525
#ModeLine "NTSC-DVD-72p" 32.357 720 760 816 856 480 482 488 525
#ModeLine "ATSC-480-59.94p" 23.916 640 664 736 760 480 482 488 525
#ModeLine "ATSC-480-60p" 23.94 640 664 736 760 480 482 488 525
#ModeLine "ATSC-480-71.93p" 28.699 640 664 736 760 480 482 488 525
#ModeLine "ATSC-480-72p" 28.728 640 664 736 760 480 482 488 525
#ModeLine "ATSC-720-59.94p" 74.086 1280 1320 1376 1648 720 722 728 750
#ModeLine "ATSC-720-60p" 74.16 1280 1320 1376 1648 720 722 728 750
#ModeLine "ATSC-720-71.93p" 88.903 1280 1320 1376 1648 720 722 728 750
#ModeLine "ATSC-720-72p" 88.992 1280 1320 1376 1648 720 722 728 750
#ModeLine "ATSC-1080-59.94i" 74.176 1920 1960 2016 2200 1080 1082 1088 1125 Interlace
#ModeLine "ATSC-1080-60i" 74.25 1920 1960 2016 2200 1080 1082 1088 1125 Interlace
#ModeLine "ATSC-1080-59.94p" 148.352 1920 1960 2016 2200 1080 1082 1088 1125
#ModeLine "ATSC-1080-60p" 148.5 1920 1960 2016 2200 1080 1082 1088 1125
#ModeLine "ATSC-1080-71.93p" 178.022 1920 1960 2016 2200 1080 1082 1088 1125
#ModeLine "ATSC-1080-72p" 178.2 1920 1960 2016 2200 1080 1082 1088 1125

Custom Modelines

Acer

Acer AT4220B / AT3720B / AT3220B / AT2720B

These screens supports 1366x768 on both the VGA input and HDMI input but the EDID data does not do this correctly. (using xorg 7.2) I have the 37" version, but I guess the electronics is the same in the whole range. Native resolution is 1366x768. Running the screen at 1368x768 will result in a little line running up the image from time to time. 1360x768 is much better, but scene changes flicker a bit some times. My 7100 nvidia card can't do the 1366x768 resolution and I'm guessing that would fix the issue.

Device section:

# Option "ExactModeTimingsDVI"
# Option "ModeValidation" "NoDFPNativeResolutionCheck"

Monitor section:

SubSection "Display"
                Modes "1360x768"

Dell

Dell 2405FPW

## (at native 1920x1200)
# Modeline    "1920x1200" 151.138 1920 1960 1992 4040 1200 1201 1204 1232  -hsync
## I have to use an older driver (1.0-7174) which does not limit the bandwidth:
# Modeline    "1920x1200" 161.75 1920 2020 2052 2184 1200 1202 1208 1235 -hsync -vsync

Fujitsu

Fujitsu 50" Plasma

## Fujitsu 50" HD Plasma (1366x768@60Hz native)
## I'm using a nVidia card so the resolution must be a multiple of 8, I use 1368x768.
## This is the modeline i got from PowerStrip. Add this to the "Monitor" section.
#	Modeline "1368x768" 85.478 1368 1424 1536 1792 768 771 777 795 +hsync +vsync
## To get this working on my computer I had to disable EDID, "UseEDID" did not work so I read through the nVidia driver
## documentation and added everything to do with disabling monitor checks (there's probably a bit of redundancy here).
## Check the latest driver documentation for more info. This can go in the "Device" or "Screen" section.
#	Option		"UseEDID" "False"
#	Option		"FlatPanelProperties" "Scaling = native"
#	Option		"ExactModeTimingsDVI" "true"
#	Option "ModeValidation" "AllowNon60HzDFPModes, NoEdidMaxPClkCheck, NoMaxPClkCheck, NoHorizSyncCheck, NoVertRefreshCheck, NoEdidDFPMaxSizeCheck, NoEdidModes"

Hitachi

Hitachi 42PD380TA

##(42"/106cm Standard Definition Plasma)
## Note: you can fine tune position and size from TV's Menu
# Modeline "1280x720@60"   74.48  1280 1468 1604 1664  720 721 724 746 +hsync +vsync
##  Works for nVidia FX 5200 PCI -> DVI to HDMI -> Sony KDF60WF655 LCD HDTV
#  The "Monitor" Section should include
#
#  Option       "IgnoreEDID"
#  Note:  For newer versions of the NVIDIA driver the line above has to be replaced with the following two lines:
#  Option       "UseEDID" "FALSE"
#  Option       "ExactModeTimingsDVI" "TRUE"
#
#  HorizSync    15 - 46
#  VertRefresh  59 - 61
#  Modeline    "1280x720p_at60Hz"   74.250 1280 1390 1430 1650 720 725 730 750 +hsync +vsync


InFocus

InFocus ScreenPlay 5000

# ModeLine "ATSC-720-59.94p" 74.176 1280 1320 1376 1650 720 722 728 750
# ModeLine "ATSC-720-60p" 74.25 1280 1320 1376 1650 720 722 728 750

InFocus X1A

# Modeline "800x600" 31.00 800 824 840 1000 600 602 603 632  # 31 MHz, 31.0 kHz, 49.1 Hz


LG

DU-37LZ30

ATSC 720p @ 60 Hz no overscan on VGA input

ModeLine "ATSC-720-60p-no-over" 74.16 1192 1310 1343 1648 672 700 705 750 +HSync +VSync

ATSC 1080i @ 60 Hz no overscan on VGA input

ModeLine "ATSC-1080-60i" 74.25 1778 1899 2002 2200 1010 1052 1068 1125 Interlace +HSync +VSync

Mitsubishi

Mitsubishi WT-46809

## Detected as 1080i
# ModeLine "960x540p" 37.26 960 976 1008 1104 540 542 548 563 +hsync +vsync

Mitsubishi WS-55513

## 1080 on DVI with a 5200
# ModeLine     "in1080i" 74.5 1760 1888 2096 2208 960 1012 1028 1126 -hsync -vsync interlace

Mitsubishi WS-48313

## I had to add the following
## HorizSync     15-75
## Option      "UseEdidFreqs" "FALSE"
# Modeline "1920x1080" 74.250 1920 2008 2052 2200 1080 1084 1094 1124 interlace +hsync +vsync

Mitsubishi HC3000u Projector

# (naitive DLP chip resolution 1280x768)
# 1280x768 at 59.94 Hz - VGA output of an nvidia 6150 graphics chip (Asus A8N-VM CSM motherboard)
# Modeline  "1280x768-Mitsubishi" 83.05 1280 1376 1504 1736 768 771 778 798  -hsync -vsync

Mitsubishi WD65732 (WDxx731, WDxx732 and WDxx831)

## I'm using the Nvidia "built in" modes, since they work fine, so here's what I used to get it working properly.
## I'm running the TV in through one of the HDMI inputs as I don't have a DVI-to-DVI cable long enough yet, for 
## the PC input DVI connector it should take more standard VGA modes as well.
## 
## My "Monitor" Horiz and Vert values were taken from the EDID information
#Section "Monitor"
#        Identifier     "WD65732"
#        HorizSync       15.0 - 68.0
#        VertRefresh     59.0 - 61.0
#EndSection
#
#
#Section "Screen"
#    Identifier     "WD65732"
#    Device         "fx5200"
#    Monitor        "WD65732"
#    DefaultDepth    24
#    Option         "NoLogo" "False"
#    Option         "IgnoreDisplayDevices" "TV"
#    Option         "DPI" "100 x 100"
#    Option "ConnectedMonitor" "DFP"
#    Option "UseDisplayDevice" "DFP-0"
#    Option "ExactModeTimingsDVI" "true"
#    Option "ModeValidation" "NoVertRefreshCheck, AllowNon60HzDFPModes, NoEdidDFPMaxSizeCheck"
#    SubSection     "Display"
#        Depth       24
#        Modes       "1920x1080_60" "1280x720_60" "720x480_60"
#    EndSubSection
#EndSection
#
#
## For the 9xxx drivers I'm using:
#Section "Screen"
#    Identifier     "WD65732"
#    Device         "fx5200"
#    Monitor        "WD65732"
#    Option         "NoLogo" "True"
#    Option         "DPI" "100 x 100"
#    Option         "ConnectedMonitor" "DFP"
#    Option         "UseDisplayDevice" "DFP-0"
#    Option         "ExactModeTimingsDVI" "true"
#    Option         "RenderAccel" "1"
#    Option         "RandRRotation" "1"
#    Option         "IgnoreDisplayDevices" "TV"
#    Option         "Coolbits" "1"
#    Option         "UseEvents" "True"
#    SubSection     "Display"
#       Depth       24
#        Modes      "1920x1080_60" "1280x720_60" "720x480_60"
#    EndSubSection
#EndSection
## Along with enabling Xvideo Vsync got rid of all the tearing and high CPU usage issues I was having.

NEC

NEC PX-50XM5 50" HD Plasma

This panel has a native resolution of 1365x768@60Hz and can be driven at this resolution using the DVI port. I tried to make it sync at 50Hz (due to PAL) with no luck.

Section "Screen"
    Monitor        "NEC PX-50XM5"
    DefaultDepth    24
    Option         "UseEDID"  "FALSE"
    Option         "UseEDIDFreqs" "FALSE"
    Option         "ModeValidation" NoEdidModes,AllowNon60HzDFPModes,NoMaxPClkCheck,NoMaxSizeCheck,NoDFPNativeResolutionCheck,NoPredefinedModes,NoVesaModes,NoVirtualSizeCheck,NoWidthAlignmentCheck,NoVertRefreshCheck,NoHorizSyncCheck,NoMaxSizeCheck,NoEdidMaxPClkCheck,NoDFPNativeResolutionCheck"
    Option         "XvmcUsesTextures" "true"
    Option         "RenderAccel" "true"
    Option         "ExactModeTimingsDVI" "true"
    Option         "FlatPanelProperties" "Scaling = Native"
    Option         "UseEvents" "TRUE"
    Option         "DPMS"
    Option         "NoLogo" "TRUE"
    SubSection     "Display"
        Viewport    0 0
        Depth       24
        Modes      "1365x768"
    EndSubSection
EndSection

Section "Monitor"
    Identifier     "NEC PX-50XM5"
    HorizSync       15.0 - 110.0
    VertRefresh     50.0 - 120.0
    ModeLine       "1365x768" 72.149 1365 1416 1466 1526 768 772 776 788 +hsync +vsync
EndSection

Olevia

Olevia LT26HVX

## This TV has a decent screen for the cost, but VGA and DVI input is
## problematic, since it reports a mode of 1280x1024 in EDID, though the native
## resolution is 1366x768, something which I wanted to take advantage of to display
## 1080i with maximum detail. After much trial and error I found several modelines
## that work when it's connected to my Radeon 8500 via DVI; I didn't have as much
## luck connected to an Nvidia card, with Windows and X. The TV doesn't seem to have
## a way to disable scaling, so even with a mode of 1360x768 or 1366x768, pixels
## don't line up perfectly. It seems close enough for video, if not for
## desktop use. It also doesn't recognize image sizes larger than 1280x1024, so I had 
## tweak those modes carefully with xvidtune to get the image centered. I use 
## 'Option "IgnoreEDID" "true"' in the Screen section. 
##
## DisplaySize  586 330
## VertRefresh 50-70
##
# Modeline "1280x768@60" 80 1280 1312 1608 1640 768 783 791 807
# Modeline "1360x768"     85.50   1360 1476 1588 1776    768  771  777  795 +hsync +vsync
# Modeline "1368x768"     85.50   1368 1478 1590 1776    768  771  777  795
#
## This works over VGA. The panel will not accept a signal over DVI with more than 720
## vertical pixels. (displays "Not Support")
#
# Modeline "1366x768" 85.50 1366 1478 1590 1776 768 771 777 795
#
## On my display, to get this as close to pixel perfect as I can tell, set in
## "Advance Picture Adjust":
##    Vertical Position 18
##    Horizontal Position 115
##    Phase 13
##    Manual Clock 117 

Olevia 537h

#Section "Monitor"
#       Identifier      "OleviaHDTV"
#       VendorName      "Olevia"
#       ModelName       "537h"
#       VertRefresh     50-80
#       HorizSync       30-85
#       Modeline "1360x768" 72.000 1360 1424 1456 1560 768 771 776 790 -hsync +vsync
#       DisplaySize     457 812
#EndSection

With an nvidia 6200LE, the above did not work for my 537h. X started, but the screen was blank. The following worked for me:

#Section "Monitor"
#         Identifier "OleviaHDTV"
#         VendorName "Olevia"
#         ModelName "537h"
#         VertRefresh 50-80
#         HorizSync 30-85
#         Modeline "1360x768" 84.50 1360 1392 1712 1744 768 783 791 807
#EndSection


Panasonic

Panasonic TX32LXD52

## panel has a native res of 1366*768 but doesn't accept this (AFAIK) over HDMI. 
## I am running an nvidia card and custom interlaced modes over DVI/HDMI are currently
## difficult to get working. 
## A good summary of the issue here - http://www.nvnews.net/vbulletin/showthread.php?t=69255
## This mode is a 1216*684@60Hz mode that I came up with through trial and error.
## Exactly what switches you pass for DPI and other checks may vary from what I have.
##
## NB: the vast array of ModeValidation arguments have arisen today since moving to 9629 
## driver release of the last few days. Tweak according to what is needed to validate the 
## mode by your driver version.
#
#Section "Monitor"
#        Identifier      "Monitor0"
#        VendorName      "Panasonic"
#        ModelName       "32in HDTV"
#        Mode "1216x684p60" 
#                DotClock 74.160
#                HTimings 1216 1356 1396 1648 
#                VTimings 684 707 712 750  
#                Flags "+hsync" "+vsync"
#        EndMode
#Section "Device"
#        Identifier      "NVIDIA Corporation NV45 [GeForce 6800GT]"
#        Driver          "nvidia"
#        BusID           "PCI:2:0:0"
#        Option          "UseDisplayDevice"      "DFP"
#        Option          "FlatPanelProperties"   "Scaling = native"
#        Option          "IgnoreDisplayDevices"  "TV, CRT"
#        Option          "ExactModeTimingsDVI"   "1"
#        Option          "NoLogo"                "1"
#        Option          "UseEDIDDpi"            "0"
#        Option          "UseEDIDFreqs"          "0"
#        Option        "ModeValidation"        "AllowNon60HzDFPModes,NoEdidMaxPClkCheck,NoVertRefreshCheck,NoHorizSyncCheck,NoDFPNativeResolutionC
heck,NoVesaModes,NoEdidModes,NoXServerModes,NoPredefinedModes"
#EndSection

Panasonic PT-AE700 Projector

#Section "Monitor"
#        Identifier      "AE-700"
#        Option          "DPMS"
#
#        Modeline  "1280x720@60" 74.160 1280 1352 1392 1648 720 725 730 750 -hsync -vsync
#EndSection

To get DVI output to work on ATI cards using the open source driver, try setting some options in the device section.

#Section "Device"
#        Identifier      "ATI Technologies Inc RV280 [Radeon 9200 PRO]"
#        Driver          "radeon"
#
#        Option "AGPMode" "4"
#        Option "MonitorLayout" "TMDS, NONE"
#        Option "DDCMode" "on"
#        Option "PanelSize" "1280x720"
#EndSection

Panasonic PT-AE900U Projector

#Section "Monitor"
#	Identifier	"Monitor0"
#       VendorName      "Panasonic"
#       ModelName       "PT-AE900U"
#	Option	"DPMS"	"true"
#       # From the User's Manual, page 62
#	HorizSync 	30.0 - 70.0
#	VertRefresh 	50.0 - 87.0
#       # From the the User's Manual, page 62 the dot clock must be < 108 MHz
#	ModeLine "1280x720"     74.52   1280 1312 1368 1676    720  724  730  750 +hsync +vsync
#EndSection

Panasonic PT-AX100U Projector

#Section "Monitor"
#       Identifier      "Configured Monitor"
#       VendorName      "Panasonic"
#       ModelName       "PT-AX100U"
#       Option          "DPMS"
#       HorizSync       30 - 70
#       VertRefresh     50 - 87
#       Modeline "1280x720@60" 74.160 1280 1308 1344 1672 720 725 730 750 -hsync -vsync
#EndSection

Panasonic TH-50PX600A, TH-50PX60A, TH-50PX70A

According to Nvidia, older drivers had a limitation where they could not accept resolutions of odd sizes: nVidia Release

This limitation has now been fixed and it is possible to run these TVs in their native resolutions (768p (1366x768)). When running with a VGA cable it seems that these TVs will not provide any EDID data. As 1366x768 is a non standard resolution you need to add a modeline to your monitor section that specifies 1366x768:

#    Modeline "1366x768" 85.500 1360 1440 1552 1792 768 771 777 795 +hsync +vsync


When running with nvidia cards you may also need to add a line that reads:

  Option       "ModeValidation" "NoDFPNativeResolutionCheck"

into your Device section.

Also take note that these TVs have a 'input resolution' setting which defaults to XGA and gives very poor results when running in their native resolutions. If the picture looks strange try pressing the 'menu' button on the remote, then going to 'Setup', 'PC setup' then changing the 'Input resolution' from XGA to WXGA. When running in native resolution also make sure you are in 16:9 mode, by pressing the 'aspect' button on the remote to bring up the 'Aspect selection' menu.


The following has been tested and works without problems:

## Plasma panel has a native res of 1366*768 but the 9xxx series of nVidia drivers only
## accept resolutions which divide by 8. So the nearest I got was 1280 x 768. No EDID is 
## passed through the PC connection to the TV - to get EDID I believe you need to connect
## via HDMI. You can find out what the valid resolutions, HorizSync and VertRefresh settings 
## are by looking in the TV manual (p39) or at 
## http://panasonic.com.au/products/specifications.cfm?objectID=3406
## HorizSync range is 31.46 - 68.38 and the VertRefresh range is 60-85.
#
#Section "Monitor"
#    Identifier     "Monitor0"
#    VendorName     "Panasonic"
#    ModelName      "TH-50PX70A"
#    HorizSync      31.46 - 68.38
#    VertRefresh    60 - 85
#    
##    Modeline for non standard 1366x768 resolution.  You may not need this if running
##    With HDMI, though I haven't tested.
#    Modeline "1366x768" 85.500 1360 1440 1552 1792 768 771 777 795 +hsync +vsync
#EndSection
#
#Section "Screen"
#    Identifier     "Screen0"
#    Device         "Videocard0"
#    Monitor        "Monitor0"
#    DefaultDepth    24
#    SubSection     "Display"
#        Viewport    0 0
#        Depth       24
#        Modes      "1280x768_60" "1280x720_60" "1024x768_60" "800x600" "640x480"
#    EndSubSection
#    ### Force 100x100 dpi as that's what MythTV is designed to run at.
#    Option         "DPI" "100 x 100"
#EndSection

Panasonic TX-42PX75U

This widescreen panel's native resolution is 1024x768. The manual says that it does not take inputs at this resolution and I have been unsuccessful when trying to drive it at this resolution. So we have to settle with a non-native resolution and put up with awful-looking text. I decided to send 720p at 60Hz.

Section "Monitor"
        ...
      	Modeline     "1208x679"   74.25   1208 1353 1393 1650   679 707 712 750  +hsync +vsync
EndSection

The TV's overscan seems to vary by a few pixels each time it is turned on so one cannot fill the screen perfectly every time. The modeline above compensates for this by being slightly smaller and leaving a few rows or columns of black (porch) pixels on either side of the viewable screen.

Improvements welcome.

Philips

Philips 190b6 TFT LCD

## Native dotclock list: 94.5(31.5) 100 108(13.5,27,36) 120(30,40) 130(65) 135 MHz
## HorizSync   30.0 - 83.0
## VertRefresh 49-76
## Option      "IgnoreEDID"
##
## 1280x1024 @ 50 Hz, 56.25 kHz, analog and digital
# Modeline "1280x1024@50" 94.5 1280 1320 1460 1680  1024 1025 1028 1125
##
## The following doesn't work over VGA since the firmware invariably assumes 556
## visible lines when driving 625@50Hz (preset: 30MHz 688x556@50Hz 960x625).
## 800x600 @ 50 Hz, 31.25 kHz, digital
# Modeline "800x600@50"   30    800  814  884  960   600  601  606  625 +hsync +vsync

Philips 190b8 TFT LCD

The monitor's firmware rejects any mode with a vertical frequency outside the 55-76 Hz range. Also, the resynchronization delay is just below 2 seconds for a distant modeswitch. Displaying a 25 frame/s video without judder requires the 75 Hz modeline below.

## Native dotclock: 100 108(13.5,27,36) 120(30,40) 126(31.5,94.5) 130(65) 135 MHz
## HorizSync   30.0 - 83.0
## VertRefresh 55-76
## Option      "IgnoreEDID"
##
## 1280x1024 @ 60 Hz, 67.5 kHz, philips 170b5 190b6 190b8
# Modeline "1280x1024@60" 108  1280 1328 1440 1600  1024 1025 1028 1125
##
## 1280x1024 @ 75 Hz, 78.75 kHz, philips 170b5 190b6 190b8
# Modeline "1280x1024@75" 126  1280 1328 1440 1600  1024 1025 1028 1050

Samsung

Samsung HL-R5678W

## Samsung HL-R5678W DLP (in 1920x1080p [over VGA input]), all resolutions without -XX are 60Hz
## The 1920x1080 (@60Hz) Modeline is confirmed working for the Samsung HL-R5078W in same manner as above
## 
# Modeline        "1920x1200" 153.918 1920 1984 2016 2080 1200 1203 1209 1235 +hsync -vsync
# Modeline        "1920x1080" 138.407 1920 1984 2016 2096 1080 1082 1087 1111 +hsync -vsync
# Modeline        "1600x1200" 162.270 1600 1672 1864 2160 1200 1201 1204 1250 +hsync +vsync
# Modeline        "1600x1024" 136.617 1600 1712 1880 2144 1024 1025 1028 1060 -hsync +vsync
# Modeline        "1280x1024" 107.981 1280 1344 1456 1688 1024 1025 1028 1066 +hsync +vsync
# Modeline        "1280x1024-70" 128.862 1280 1384 1520 1728 1024 1025 1028 1066 -hsync +vsync
# Modeline        "1280x1024-72" 133.038 1280 1384 1520 1728 1024 1025 1028 1067 -hsync +vsync
# Modeline        "1280x1024-75" 135.126 1280 1312 1456 1688 1024 1025 1028 1066 +hsync +vsync
# Modeline        "1280x960" 107.981 1280 1392 1504 1800 960 965 968 1000 +hsync +vsync
# Modeline        "1280x768" 79.464 1280 1360 1488 1664 768 771 778 798 -hsync +vsync
# Modeline        "1280x768-70" 95.055 1280 1368 1504 1696 768 769 772 800 -hsync +vsync
# Modeline        "1280x768-72" 97.839 1280 1368 1504 1696 768 769 772 801 -hsync +vsync
# Modeline        "1280x768-75" 102.271 1280 1376 1504 1696 768 771 778 805 -hsync +vsync
# Modeline        "1280x720" 74.453 1280 1448 1584 1696 720 721 724 746 -hsync +vsync
# Modeline        "1152x864" 107.981 1152 1232 1360 1616 864 865 868 900 +hsync +vsync
# Modeline        "1024x768" 74.871 1024 1064 1200 1344 768 771 777 806 -hsync -vsync
# Modeline        "800x600-56" 36.018 800 848 920 1040 600 601 603 625 +hsync +vsync
# Modeline        "800x600" 40.025 800 856 984 1056 600 601 605 628 +hsync +vsync

Samsung LE32R51B / LE26Rx / LE37R4 / LE40R5 / LE32R71 (B/W)

## DisplaySize             349 196
# Modeline                "1360x768" 85.500 1360 1424 1536 1792 768 771 777 795 +Hsync +Vsync

Samsung LA40R81BD

## Samsung LA40R81BD LCD TV [over HDMI2 input]
# Modeline          "1360x768@60" 85.800 1360 1440 1552 1792 768 771 777 795 +hsync +vsync
# DisplaySize       349 196
#
# You will probably have to disable DDC/EDID
# So will need these also. (They work for 1360x768@60 but not sure if they are totally correct.)
# HorizSync         30-61
# VertRefresh       60-75
#
# Also in Device disable DDC/EDID
# e.g. For Xorg Radeon driver
# Section "Device"
#        Identifier "ATIVideocard0"
#        Driver     "radeon"
#        #### # Remove DDC
#        Option     "NoDDC" "on"
#        Option     "DDCMode" "off"
#        Option     "IgnoreEDID" "on"
# EndSection

Samsung LA46M81BDX

For a 50Hz modeline to prevent judder on stock/news tickers and scrolling credits when viewing PAL DVB:

Section "Device"
         Option "ModeValidation" "NoMaxPClkCheck, AllowNon60HzDFPModes"
         # Samsung LA46M81BDX LCD TV [over HDMI2 input]
         Modeline "1920x1080@50" 148.50 1920 2448 2492 2640 1080 1084 1089 1125
EndSection

Samsung LNR328W

# Modeline        "1360x768" 85.5 1360 1416 1528 1792 768 771 777 795 +hsync +vsync

Samsung LNR3255W

# Modeline    "1360x768" 84.50 1360 1392 1712 1744 768 783 791 807 +hsync +vsync

Samsung LNS3241D / LNS3251D

## Used `get-edid | parse-edid` to determine this modeline:
# Modeline     "1360x768" 85.50  1360 1424 1536 1792  768 771 777 795 +HSync +VSync
## Also had to set the Horizontal/Vertical Freq.: 
# HorizSync    47.7 - 47.7
# VertRefresh  60.0 - 60.0
## Don't know if this is necessary for correct DPI, but the display size is:
# DisplaySize  692 394

Samsung LNT4661F / LNT4061F / LNT4065F / LNT4665F / LNT5265F

# Samsung LNT4661F (VGA input).  Given that the manual is identical, this should also
# work for models LNT4061F, LNT4065F, LNT4665F and LNT5265F
Section "Monitor"
    Identifier     "Monitor0"
    VendorName     "Samsung"
    ModelName      "LNT4661F"
    HorizSync       15.0 - 80.0
    VertRefresh     50.0 - 100.0
    Modeline       "1920x1080" 138.500   1920 1960 1995 2083   1080 1082 1087 1109  +hsync -vsync
    Option         "dpms"
EndSection
# Video card is an NVidia GeForce FX 5200.  Using the binary driver from NVidia, I appear
# to need this line in my "Screen" section.  It's likely some of these options are not needed
# but I've been too lazy to figure out which ones.
    Option         "ModeValidation" "AllowNon60HzDFPModes,NoEdidMaxPClkCheck,NoVertRefreshCheck,NoHorizSyncCheck,NoDFPNativeResolutionCheck,NoVesaModes,NoEdidModes,NoXServerModes,NoPredefinedModes"
#

Sanyo

Sanyo ViZZon DP42647 42" LCD

## Samsung Sanyo DP42647 42 inch LCD TV
ModeLine "1280x720" 74.48 1280 1468 1604 1664 720 721 724 746 +hsync +vsync
# If doesn't fill the screen, use the TV's aspect ratio to fix

Sanyo PLV Z4/Z5

## Samsung Sanyo PLV Z4 and PLV Z5 projector
# DisplaySize 325 182  # For 1280x720 at 100dpi  (16:9)
# HorizSync   30.0 - 62.0
# VertRefresh 50.0 - 85.0
# Modeline    "1280x720@60Hz" 73.78 1280 1312 1592 1624 720 735 742 757
# Modeline    "1280x720@50Hz" 59.42 1280 1312 1536 1568 720 735 741 757

Sceptre

Sceptre X37SV-Naga

## (37" 1920x1080 60Mhz native resolution LCD)
## Using Nvidia FX5200 DVI->HDMI cable connected to the LCD
## I had to use the following options for any modes greater than 1280x1024 to work when using the DVI->HDMI 
## output, I didn't need these options for VGA output to the LCD.
#   Option "ModeValidation" "NoMaxPClkCheck, NoEdidMaxPClkCheck"
#   Option "UseDisplayDevice" "DFP"
#
#   Modeline for the LCD's native resolution
#   ModeLine "1920x1080p" 148.500 1920 2024 2072 2200 1080 1084 1094 1124 -hsync -vsync

Sharp

Sharp LC-37D6U

# Modeline "1080x680" 79.68 1080 1492 1532 1752 680 722 724 758

Sharp LC-40C32U

## with ubuntu edgy's x.org and the nvidia 8776 drivers, a simple mode of "1360x768" works without
## the custom modeline
#Section "Monitor"
#        Identifier      "Sharp LC-40C32U"
#        HorizSync       24-62
#        VertRefresh     49-76
#
#        modelines from the web generator at
#        http://xtiming.sourceforge.net/cgi-bin/xtiming.pl
#        Modeline "1360x768@60" 84.50 1360 1392 1712 1744 768 783 791 807
#
#        EDID-derived modelines
#        ModeLine "1360x768@60" 85.5 1360 1424 1536 1792 768 771 777 795 +hsync +vsync
#EndSection

On Fedora Core 6, with the nVidia 9746 driver, the following will work for 1360x768 mode using a DVI connection:

Section "Monitor"
    Identifier    "Monitor0"
    VendorName    "Sharp"
    ModelName     "LC-40C32U"
    Option        "ModeValidation" "NoDFPNativeResolutionCheck"
    Option        "DPMS"
EndSection

Section "Screen"
    Identifier    "Screen0"
    Device        "Videocard0"
    Monitor       "Monitor0"
    DefaultDepth  24
    SubSection    "Display"
        Viewport  0 0
        Depth     24
        Modes     "1360x768" "1024x768"
    EndSubSection
EndSection

The monitor sends back an inaccurate maximum DFP size, making it necessary to disable the native resolution check.

NOTE: This TV requires that you manually select a 1360x768 input signal through the on-screen menu. See your TV's manual for details.


Sharp LC-46D64U

   ModeLine "1920x1080@65" 160.875 1920 2008 2052 2200 1080 1084 1089 1125 +hsync +vsync


Sharp LC-46D92U

Using the nvidia binary drivers version 9746. Outputting 1920x1080 over DVI to the display. Graphics card is a GeForce 6600 with 256MB of VRAM.

This is the same modeline as the Vizio GV47L and I got it from this wiki. So thanks to the person who put it there.

I had to disable native resolution check because the EDID information returned by the display was reporting a max resolution of "1280x1024". Here is the Monitor section:

Section "Monitor"

    Identifier  "Sharp LCD HDTV"
    ModeLine "1920x1080_60-Sharp_D92U" 148.35 1920 2008 2052 2200 1080 1085 1090 1125 +hsync +vsync
    Option "ExactModeTimingsDVI" "TRUE"
    Option "ModeValidation" "NoDFPNativeResolutionCheck"

EndSection

Sharp LC-46X20E

Im using Onboard Intel X3100 graphic Card with Intel driver... EDID workes only for 50Hz, this Modelines enable 60Hz and 24Hz. Im using "xrandr --output TMDS-1 --mode 1920x1080@24 for switching...

Section "Monitor"
        Identifier      "Sharp LC-46X20E"
        Modeline "1920x1080@24" 74.250 1920 2560 2608 2752 1080 1084 1089 1125 +hsync +vsync
        Modeline "1920x1080@50" 148.500 1920 2448 2492 2640 1080 1084 1089 1125 +hsync +vsync
        Modeline "1920x1080@60" 148.500 1920 2008 2056 2200 1080 1084 1089 1125 +hsync +vsync
EndSection

Sony

Sony KP-46WT520

# Device "NVIDIA Corporation NV18 [GeForce4 MX 440 AGP 8x]"
# HorizSync 15.0 - 46.0
# VertRefresh 59.0 - 61.0
# Option "DPMS"
# Option "IgnoreEDID"
# ModeLine "1160x652" 74.48 1160 1208 1328 1664 652 653 656 746 -hsync +vsync

Sony KF-50WE610

## nVidia FX5200, DVI
## HorizSync       15.0 - 46.0
## VertRefresh     59.0 - 61.0
# Modeline "1152x648" 74.2 1152 1288 1328 1648 648 689 694 750 +hsync +vsync

Sony KDF-E42A10

## You'll also need to add Option "IgnoreEDID" "true" to the Screen section
## since the TV incorrectly reports as 1920x540.
## For 1920x1080 I had to add 
##       Option      "ModeValidation" "NoVertRefreshCheck"
## to the device section. Tested w/ FX5200 DVI -> HDMI using nvidia drivers.
# ModeLine "1280x720" 74.25 1280 1390 1430 1648 720 725 732 752 +hsync +vsync
# ModeLine "1920x1080" 74.25 1920 2008 2052 2200 1080 1088 1091 1121 +hsync +vsync

Sony KDF-46E2000

## Valid widescreen modes from the manual are 1280x768_60 and 1152x648_60
## However, 1280x768 failed the NVidia 'Native DFP Resolution Check'.
## Adding the following two lines to the 'Screen' section of xorg.conf got
## 1280x768 working:
#       Option "metamodes" "1280x768_60 +0+0; 1152x648_60 +0+0; 640x480 +0+0"
#       Option "ModeValidation" "NoDFPNativeResolutionCheck"

Sony Bravia KLV-S32A10E (KLV-S40A10E, KLV-S32A10E, KLV-S26A10E, KLV-S23A10E, KLV-S19A10E)

#Section "Monitor"
#        Identifier      "KDL-S32A12U"
#        Option          "DPMS"
#        HorizSync       31-60
#        VertRefresh     56-75
#        Modeline        "1280x768" 80.14 1280 1344 1480 1680 768 769 772 795 -hsync +vsync
#EndSection
#
#Section "Screen"
#        Identifier      "Default Screen"
#        Device          "VIA Technologies, Inc. VT8623 [Apollo CLE266] integrated CastleRock graphics"
#        Monitor         "KDL-S32A12U"
#        DefaultDepth    24
#        SubSection "Display"
#               Depth           24
#               Modes           "1280x768" "1024x768"
#        EndSubSection
# EndSection

Sony KDL-40W2000 (European model)

## 1080p native LCD 
## For some reason the native 1080p modes were failing the validation due to incorrectly checking the maxpixelclock
## You need the "NoMaxPClkCheck" to get 1080p and "AllowNon60HzDFPModes" to use 50Hz (1920x1080_50) 
## The last 3 are optional just to limit to EDID modes reported by the screen only
##
## Section "Device"
##    	Identifier "dev2"
##    	Driver "nvidia"
##    	BusID "PCI:1:0:0"
##    	Option		"UseFBDev"		"true" 
##      Option  "ModeValidation" "NoMaxPClkCheck, AllowNon60HzDFPModes, NoVesaModes, NoXServerModes, NoPredefinedModes"        
##	Screen 1
## EndSection

Sony KDL-40V2500

## I used DVI to HDMI on the HDMI input 6 (the one with RCA audio jacks). 
## Make sure you have display area set to full otherwise you will be tricked into thinking you have overscan -- see pages 29 and 30 of the product manual on how to set to full
## The picture looks great from an nVidia 7600 GS
##
#Section "Monitor"
#   Identifier     "Monitor[0]"
#   VendorName     "Sony"
#   ModelName      "SonyHDTV"
#   UseModes       "Modes[0]"
#   DisplaySize     320 180
#   HorizSync       20.0 - 150.0
#  VertRefresh     30.0 - 90.0
#   Option         "UseDisplayDevice" "DFP"
#   Option         "IgnoreDisplayDevices" "TV, CRT"
#   Option         "ExactModeTimingsDVI" "1"
#   Option         "NoLogo" "0"
#   Option         "UseEDIDDpi" "0"
#   Option         "UseEDIDFreqs" "0"
#   Option         "RenderAccel" "true"
#   Option         "AllowGLXWithComposite" "true"
#   Option         "ConnectedMonitor" "DFP"
#   Option         "ModeValidation"
#EndSection

#Modeline "1920x1080p60" 148.35 1920 2008 2052 2200 1080 1084 1089 1125 +Hsync +Vsync

## NOTE the 'Option         "ModeValidation"' line with no args -- I had issues getting this mode to validate -- so this just seems to make all happy.
## NOTE DisplaySize is fudged to get a reasonably large font from X, if you use the real dimensions -- you will be doing alot of squinting... 

Sony KDS-R60XBR1

## Make sure that you don't use the IgnoreEDID option becase it work with this option
## unlike some other Sony models.
## The picture is still does not fit perfect but pretty close. I am using 1152x648 now.
## HorizSync       31.5 - 37.9
## VertRefresh     59.9 - 60.1
#  ModeLine       "1280x720" 74.2 1280 1390 1426 1646 720 725 727 747 +hsync +vsync
#  ModeLine       "1920x1080" 74.2 1920 2008 2052 2200 1080 1088 1091 1121 +hsync +vsync interlace
#  ModeLine       "1152x648" 74.2 1152 1288 1328 1648 648 689 694 750 +hsync +vsync

Sony KDL-26S2000

This excerpt from xorg.conf works for both 720p (as shown) and 1080i (put "1920x1080" first in the Modes line the Screen section) under mythbuntu and connecting through an HDMI cable.

Section "Monitor"
        Identifier  "Sony KDL-26S2000 HDMI"
EndSection

Section "Device"
        Identifier  "ATI Radeon HD 2600PRO"
        Driver      "fglrx"
        BusID       "PCI:1:0:0"
EndSection

Section "Screen"
        Identifier "DVI"
        Device     "ATI Radeon HD 2600PRO"
        Monitor    "Sony KDL-26S2000 HDMI"
        DefaultDepth     24
        SubSection "Display"
                Depth     24
                Modes    "1280x720" "1920x1080" "640x480"
        EndSubSection
EndSection

Sony KDL-40S2000

I am able to get the picture exactly as it is with XP under Ubuntu with these settings.

HorizSync    30-66
VertRefresh  30-61
Modeline "1360x768"   85.500   1360 1432 1544 1792   768 771 777 795

Sony KDL-32M3000

This works great for me with VGA cable connection.

Horizsync       31.5-48.0
Vertrefresh     56.0 - 65.0
ModeLine "1360x768" 85.500 1360 1424 1536 1792 768 771 777 795 +Hsync +Vsync

Toshiba

Toshiba 42A3000A

## ATI 9250 AGB, DVI 
## Have not figured out how to force Xorg to set it all up automatically so I have to use xrandr)
## 42 Inch widescree tv
## HorizSync 15-46
## VertRefresh 49-61
# Modeline "1280x720" 74.48 1280 1336 1472 1664 720 721 724 746 -hsync +vsync
# TV will start in lower resolution,  Modeline "720x576"x50.0   27.00  720 732 796 864  576 581 586 625 -hsync -vsync (31.2 kHz)
# Script to run after logging on to my computer
xrandr --output DVI-0 --newmode 1280x720 74.48 1280 1336 1472 1664 720 721 724 746 -hsync +vsync
xrandr --addmode DVI-0 1280x720
xrandr --output DVI-0 --mode  1280x720

#If anyone knows how to configure xorg and force it to do this in xorg.conf, feel free to email me with info.
#martin(youknowwhat)forest(d)gen(d)nz

Toshiba 42H83

## nVidia FX5200, DVI 
## (obsolete by X.org-7.0 and NVidia-8774; 1280x720 built-in mode now works)
## DisplaySize 93 52
## HorizSync 31-46
## VertRefresh 59-61
## Option "DPMS"
# Modeline "960x540p" 40.86 960 992 1144 1176 540 551 557 568 +HSync +VSync

Toshiba 50H81

## Connected through an Audio Authority Scan Converter (Model A960)
##    *I have these settings to help protect TV if I play with other modes later:
##        HorizSync 15 - 33.85
##        VertRefresh 29.9 - 60.1
##     Last revised Oct-2006
##
## Use in540p for menus/mythplugins         (  880x480p ) 
## Use 640x480p to playback SD recordings   (  640x480p )
## Use 1080i for HD Content                 ( 1760x960i )
# ModeLine "in540p"           37.26  880  944  1048 1104   480  506  520  563  +hsync +vsync
# Modeline "640x480p"          26.964 640  704  768  856    480  486  492  525  -hsync -vsync
# ModeLine "in1080i"          74.52  1760 1888 2096 2208   960  1012 1028 1126 -hsync -vsync interlace

Toshiba HD51

## Note: using an NVidia GeForce 6200 w/ Component Video dongle -- does not work with S-Video connected at the same time
# Option         "TVStandard" "HD720p"
# Option         "TVOutFormat" "SVIDEO"
# Option         "ConnectedMonitor" "TV"
# Option         "NoLogo" "True"
# Option         "NvAGP" "1"
#
# ModeLine       "720p" 73.8 1280 1320 1368 1640 720 722 724 751 +hsync +vsync

Toshiba 56HM66 DLP

##Despite the manual stating it cannot be connected to a computer
## I have mythtv running in 720p (the native mode of the tv) using an NVidia fx5200 via dvi->hdmi cable

Section "Monitor"
        Identifier   "Monitor0"
        VendorName   "Toshiba 56HM66"
        ModelName    "56HM66"
        HorizSync    44.9 - 45.1
        VertRefresh  59.9 - 61.1
        Modeline        "1280x720" 75.288 1280 1397 1445 1672 720 725 730 750 +hsync +vsync
EndSection

Toshiba REGZA 52" 1080p LCD 52HL167

# Note: this assumes Nvidia video card connected via DVI->HDMI.  These modes
#       are primarily useful if the TV is not on when X is started or
#       an HDMI switching receiver isn't set to the proper input when X
#       is started.
Section "Monitor"
        Identifier   "Monitor0"

        VendorName   "Toshiba"
        ModelName    "Toshiba REGZA 52HL167"

        # Connected via DVI (may not be able to detect if TV off otherwise)
        Option "ConnectedMonitor" "DFP"

        Option "USEEDIDDpi" "FALSE"
        Option "DPI" "100 x 100"

        # Necessary as if TV is not on, default Freqs are not right
        Option "UseEDIDFreqs" "FALSE"

        # Necessary otherwise states max size is 640x480
        Option "ModeValidation" "NoDFPNativeResolutionCheck"

        # Necessary or cannot calculate timings errors
        Option "ExactModeTimingsDVI" "true"

        # Refresh timings as per EDID info on TV. Necessary if TV is off
        HorizSync   15.000 - 68.000
        VertRefresh 23.000 - 61.000

        # Modes taken from EDID of TV:
        # 1080p @ 60Hz
        ModeLine  "1920x1080" 148.50 1920 2008 2052 2200 1080 1084 1089 1125 +hsync +vsync
        #  720p @ 60Hz
        ModeLine  "1280x720"   74.25 1280 1390 1430 1650  720  725  730  750 +hsync +vsync
        #  480p @ 60Hz
        ModeLine  "720x480"    27.00  720  736  798  858  480  489  495  525 -hsync -vsync
EndSection

ViewSonic

ViewSonic N2750w

## HorizSync    30.0 - 80.0
## VertRefresh  50.0 - 75.0
## Option      "dpms"
## DisplaySize 325 182
# Modeline "1280x720" 75 1280 1336 1472 1664 720 725 730 75

ViewSonic N3251w (or ViewSonic N3760w)

## -- Monitor Section --
## Actual native for the monitor is 1366x768, however my nVidia card requires it to be either 
## 1360x768 or 1368x768.
##
## HorizSync 30.0 - 64.0
## VertRefresh 60.0 - 75.0
# Modeline "1368x768" 85.478 1368 1424 1536 1792 768 771 777 795 +hsync +vsync

## -- Device Section --
# Option "IgnoreEDID" "True"

ViewSonic VG2230wm

# EDID derived values with 170 being the maximum pixel clock of my nVidia card.
Section "Monitor"
        Identifier   "Monitor-Center"
        VendorName   "ViewSonic"
        ModelName    "VG2230wm"
        DisplaySize  470 300
        HorizSync    30.0 - 82.0
        VertRefresh  50.0 - 75.0
        ModeLine     "1680x1050"  170.00  1680 1784 1960 2240  1050 1053 1059 1089 +hsync +vsync
        Option       "dpms"
EndSection

ViewSonic N4280p

#Mode line i got from powerstrip, very close to the ATSC1080 modeline -
#couldn't get this to work with either at 9800pro or a X1600 (the X1600 did
#work on a windows xp machine). Put a geforce 7600 in the machine and it works 
#like a dream.
Section "Monitor"
        Identifier   "Monitor0"
        VendorName   "Monitor Vendor"
        ModelName    "Monitor Model"
        HorizSync       30 - 64
        VertRefresh     60 - 75
        Modeline "1920x1024" 148.500 1920 2008 2052 2200 1080 1084 1089 1125 +Hsync +Vsync
        #1920x1080 Display Size
        #DisplaySize 487 274
#this is nvidia specific -- Have to over ride this to get 
#it to use DisplaySize
        Option    "DPI"  "100 x 100" 
EndSection

Westinghouse

Westinghouse LVM-42W2 42" LCD

Section "Monitor"
        Identifier   "Monitor1"
        VendorName   "Westinghouse"
        ModelName    "LVM-42w2"
        ### From /var/log/Xorg.0.log: ###
        # Supported additional Video Mode:
        # clock: 138.5 MHz   Image Size:  930 x 520 mm
        # h_active: 1920  h_sync: 1968  h_sync_end 2000 h_blank_end 2080 h_border: 0
        # v_active: 1080  v_sync: 1082  v_sync_end 1087 v_blanking: 1111 v_border: 0
        # Ranges: V min: 50  V max: 75 Hz, H min: 30  H max: 80 kHz, PixClock max 150 MHz
        VertRefresh  50.0 - 75.0
        HorizSync    30.0 - 80.0
        ModeLine     "1920x1080" 138.5 1920 1968 2000 2080 1080 1082 1087 1111

        Option  "DPMS"  "true"
        Option "UseEdidDpi" "FALSE"
        Option "DPI" "100 x 100"
EndSection

Westinghouse SK-32H240S (32" LCD)

This is an inexpensive 32-inch 720p HDTV set sold by several retailers. Also, it doesn't put out EDID information over the VGA port (maybe it does on HDMI).

Section "Monitor"
        Identifier      "Monitor"
        VendorName      "Westinghouse"
        ModelName       "SK-32H240S"

        DisplaySize     710     401
        HorizSync       30 - 49
        VertRefresh     50 - 75

        Option          "DPMS"  "True"

        Modeline        "1368x768"  73.250      1368 1408 1440 1496     768 771 776 816 +hsync -vsync
EndSection

Zenith

Zenith P60W26 60" Plasma

# Connected directly to the VGA input
# Modeline "1280x720_70.00"  89.04  1280 1352 1488 1696  720 721 724 750  -HSync +Vsync


Others

AWA 81cm LCD

## AWA 81cm LCD
## HorizSync   30-80
## VertRefresh 56-85
## Option "UseEdidFreqs"   "false"
# ModeLine "1360x768" 84.6 1360 1424 1568 1776 768 769 774 795

Tevion or Medion 41427 (Aldi)

## Tevion or Medion 41427 (also sold as Aldi LCD) 60Hz modeline
#	Modeline "1280x720@60" 74.20 1280 1390 1430 1650 720 725 730 750 +hsync +vsync


Vizio GV47L

##  Modeline for 1080p -- 1920x1080_60 for the Vizio GV47L
#	ModeLine "1920x1080_60-GV47L" 148.35 1920 2008 2052 2200 1080 1085 1090 1125 +hsync +vsync
## Nvidia drivers (at least the current 9746) require the following options in the card "Device" section of the xorg.conf file
#   Option      "ExactModeTimingsDVI" "True"
#   Option      "ModeValidation" "NoDFPNativeResolutionCheck"

Vizio l47

This modeline gets my l47 displaying 720p correctly:

Modeline "720p" 82.61 1368 1424 1579 1754 768 770 757 793 +hsync +vsync # WORKS


Polaroid (Proview) FLM-3232

No modelines are really necessary for this one over the VGA. Here are the relevant xorg.conf pieces to display at the max resolution of 720p:

Section "Monitor"
        HorizSync    30.0 - 81.0
        VertRefresh  56.0 - 75.0
        Identifier   "Monitor0"
        VendorName   "Polaroid"
        ModelName    "FLM-3232"
EndSection

Section "Device"
        Identifier  "Videocard0"
        Driver      "nvidia"
        VendorName  "XFX"
        BoardName   "XFX nVidia GeForce 6200"
        Option      "RenderAccel" "1"
        Option      "NvAGP" "2"
        Option      "NoLogo" "true"
        Option      "UseEvents" "True"
EndSection

Section "Screen"
        Identifier "Screen0"
        Device     "Videocard0"
        Monitor    "Monitor0"
        DefaultDepth     24
        SubSection "Display"
                Viewport   0 0
                Depth   24
                Modes   "1920x1080_60" "1280x720_60" "720x480_60"
                #       1080p           720p            480p
        EndSubSection
EndSection

Tatung 32" 81cm HDTV

# Scaling by the DFP, ModeLine necessary, plus validation checks switched off:

Section "Monitor"

    Identifier  "Mon1"
    HorizSync    15.0 - 46.0
    VertRefresh  49.0 - 61.0
    ModeLine "1920x1080" 74.250 1920 2008 2052 2200 1080 1084 1094 1125 interlace +hsync +vsync
#    Option    "DPMS"
EndSection

Section "Device"
    Identifier                          "NV2"
    Driver                              "nvidia"
    Option "AddARGBGLXVisuals" "True"
    Option "DisableGLXRootClipping" "true"

        Option "NoVertRefreshCheck"
        Option  "ModeValidation" "NoVertRefreshCheck,NoDFPNativeResolutionCheck,NoEdidMaxPClkCheck,NoHorizSyncCheck,NoMaxPClkCheck"
        Option "UseEDIDDpi" "false"
        Option "ExactModeTimingsDVI" "true"
        Option "FlatPanelProperties" "Scaling=Native"

    BusID "PCI:5:0:0"
    Screen 1
EndSection

Section "Screen"
    Identifier  "Screen1"
    Device      "NV2"
    Monitor     "Mon1"
    DefaultDepth 24

    Subsection "Display"
        Depth       24
        Modes "1920x1080_60i"
        # "1280x720" "640x480"
        ViewPort    0 0  # initial origin if mode is smaller than desktop
    EndSubsection
EndSection

Ventura Wide

Modelines to run the full resolution of 1366x768, on a Ventura Wide panel. In Denmark sold by Mermaid Computers.

##  Modeline for 1366
# ModeLine	"1366x768" 85.9 1366 1438 1626 1798 768 769 772 795 +hsync +vsync
## Nvidia drivers require the following options in the card "Device" section of the xorg.conf file
# Option      "ExactModeTimingsDVI" "True"
# Option      "ModeValidation"  "NoWidthAlignmentCheck, NoDFPNativeResolutionCheck"

See Also

Working with Modelines

Sources

http://gentoo-wiki.com/HOWTO_Xorg_HDTV