Difference between revisions of "Silicondust HDHomeRun Plus"
From MythTV Official Wiki
m (→Setting the Default Transcode Profile) |
(No longer sold by SiliconDust) |
||
| (6 intermediate revisions by 3 users not shown) | |||
| Line 1: | Line 1: | ||
| − | Networked, dual-tuner for North American broadcast and cable TV including hardware to transcode to mobile-device-friendly formats. See [[Silicondust_HDHomeRun]] for other models available. | + | Also known as the HDHomerun Extend. Networked, dual-tuner for North American broadcast and cable TV including hardware to transcode to mobile-device-friendly formats. Now discontinued. See [[Silicondust_HDHomeRun]] for other models available. |
[[File:HDHomerunPlus.jpg|350px|thumb|right]] | [[File:HDHomerunPlus.jpg|350px|thumb|right]] | ||
| + | ==Setting the Default Transcode Profile== | ||
| − | + | Navigate to the web page for your HDHomeRun Plus. On Mac/Linux, open a terminal window and run: | |
| − | + | hdhomerun_config discover | |
| − | + | This will display the device ID and IP address for your HDHomeRun; enter that IP address into your web browser. Click on Transcode Configuration. Select the preferred Default Transcode Configuration | |
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | + | There is no specific support for the HDHomeRun Plus in MythTV but it will function similar to an HDHomeRun Dual. (See the [[Hdhomerun#Setup_Instructions|configuration instructions]] for that device.) The exception is [[multirec]] if you configure the HDHomeRun Plus to enable transcoding. Since the HDHomeRun Plus is only capable of transcoding one stream per tuner, MythTV can only record one (1) program from a stream. Thus you must set the number of virtual tuners to 1 for an HDHomeRun Plus if you configure the device to transcode. | |
| − | |||
| − | |||
| − | |||
| − | ==Transcoding Profiles== | + | ===Transcoding Profiles=== |
| + | {{Note box|The maximum payload data rate for an ATSC 1.0 channel is approximately 18.3 Mbps. This includes all streams/subchannels.}} | ||
{| class="wikitable" | {| class="wikitable" | ||
|+HDHomerun Plus Transcode Profiles | |+HDHomerun Plus Transcode Profiles | ||
| Line 48: | Line 18: | ||
! Profile | ! Profile | ||
! Resolution/frame rate | ! Resolution/frame rate | ||
| − | ! | + | ! Bitrate (approx.) |
|- | |- | ||
| Heavy | | Heavy | ||
| Same as source | | Same as source | ||
| − | | | + | | 7 Mb/s |
|- | |- | ||
| Mobile | | Mobile | ||
| − | | | + | | 1280x720 30fps |
| − | | | + | | 3 Mb/s |
|- | |- | ||
| + | | Internet540 | ||
| + | | 960x540 30 fps | ||
| + | | 3 Mb/s | ||
| + | |- | ||
| Internet480 | | Internet480 | ||
| − | | | + | | 848x480 30 fps |
| − | | | + | | 2 Mb/s |
| + | |- | ||
| + | | Internet360 | ||
| + | | 640x360 30 fps | ||
| + | | 1.5 Mb/s | ||
| + | |- | ||
| + | | Internet240 | ||
| + | | 432x240 30 fps | ||
| + | | 1 Mb/s | ||
|- | |- | ||
|} | |} | ||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
[[Category:Hardware]][[Category:HDHomeRun]] | [[Category:Hardware]][[Category:HDHomeRun]] | ||
Latest revision as of 12:04, 23 September 2021
Also known as the HDHomerun Extend. Networked, dual-tuner for North American broadcast and cable TV including hardware to transcode to mobile-device-friendly formats. Now discontinued. See Silicondust_HDHomeRun for other models available.
Setting the Default Transcode Profile
Navigate to the web page for your HDHomeRun Plus. On Mac/Linux, open a terminal window and run: hdhomerun_config discover This will display the device ID and IP address for your HDHomeRun; enter that IP address into your web browser. Click on Transcode Configuration. Select the preferred Default Transcode Configuration
There is no specific support for the HDHomeRun Plus in MythTV but it will function similar to an HDHomeRun Dual. (See the configuration instructions for that device.) The exception is multirec if you configure the HDHomeRun Plus to enable transcoding. Since the HDHomeRun Plus is only capable of transcoding one stream per tuner, MythTV can only record one (1) program from a stream. Thus you must set the number of virtual tuners to 1 for an HDHomeRun Plus if you configure the device to transcode.
Transcoding Profiles
Note: The maximum payload data rate for an ATSC 1.0 channel is approximately 18.3 Mbps. This includes all streams/subchannels.
| Profile | Resolution/frame rate | Bitrate (approx.) |
|---|---|---|
| Heavy | Same as source | 7 Mb/s |
| Mobile | 1280x720 30fps | 3 Mb/s |
| Internet540 | 960x540 30 fps | 3 Mb/s |
| Internet480 | 848x480 30 fps | 2 Mb/s |
| Internet360 | 640x360 30 fps | 1.5 Mb/s |
| Internet240 | 432x240 30 fps | 1 Mb/s |
