User:Keithamus
Setup
I currently have a single system setup, a front/back end, for SD/HD use.
Pundit-pvr
|
Why I chose this system
- The whole system was very cheap, around £200 ($400).
- It has quite a small footprint, although much bigger than a set-top-box, it is no way as big as a desktop case.
- It looks quite stylish, which is always good for the WAF
- It'll run HD content.
- I chose the cheapest Core2Duo I could find. Any Core2Duo PC should be able to run atleast 720p content. Although dedicated HD graphics is recommended.
Problems
- The Pundit P3 is a low profile system, as such, you'll need low profile cards. The Nova T 500 is not a low profile card, so you'll have to remove the PCI plate, and have the card lose in the slot (this is not desirable, as the card can easily become de-seated!) support@hauppauge.com will send you out at blanking plate, don't expect any correspondance, I tried several times asking about it, then finally just emailed my address over in the hopes of getting it, and 2 days later a blanking plate was in the post!
- The system isn't as quiet as I'd like - the stock cooler is quite whiny, and the stock case fan (attached with only 1 screw!) is very loud. Getting a good Scythe fan or two would definitely be recommended. With stock cooling the air runs cold - so you could probably get away with a small heatsink over the CPU and a good, quiet case fan.
- Still having slight problems with Mythbuntu. Overall I would say the system is worth it, but has its annoyances.
Real world figures
In terms of crunching power, wattage and temperatures, this system really can't be complained about;
- I've been able to record 2 channels and watch HD-720p content with NO lag. Even with integrated graphics.
- 500GB is a hefty size for storing data. It'll easily store more content than you're likely to watch. Having said this, I'm beggining to run out of space, and 1TB is about £70, so cheap enough for consideration!
- 1024mb seems to be enough. I would consider upgrading this if you have a bit more spare cash.
- Because its a relatively "slow" core 2 duo, its cold to the touch - with the stock cooler, but more than capable of running 720p
Notes on getting Mythbuntu working properly
Hard Drive optimisation
A good partition setup is as follows:
- 20gb / ext3
- 1GB SWAP (make this the same as the installed memory for easy sleep/hibernation)
- Rest as /var/lib/ xfs
I would recommend setting the noatime and nodiratime options to your drives, for less intensive harddisk access. To do this, go to your /etc/fstab which may look like this, for example:
# /dev/sda1 UUID=6e039164-c59f-49f1-9b96-e658a24aac2d / ext3 errors=remount-ro 0 1 # /dev/sda3 UUID=d8af15ba-f63e-465d-848e-9c8d3d020e4a /var/lib xfs relatime 0 2 # /dev/sda2 UUID=07a339be-0944-4a04-a71a-9b1e173cbb6e none swap sw 0 0 /dev/scd0 /media/cdrom0 udf,iso9660 user,noauto,exec,utf8 0 0
Change this file to look more like this:
# /dev/sda1 UUID=6e039164-c59f-49f1-9b96-e658a24aac2d / ext3 noatime,errors=remount-ro 0 1 # /dev/sda3 UUID=d8af15ba-f63e-465d-848e-9c8d3d020e4a /var/lib xfs noatime,nodiratime,logbufs=8 0 2 # /dev/sda2 UUID=07a339be-0944-4a04-a71a-9b1e173cbb6e none swap sw 0 0 /dev/scd0 /media/cdrom0 udf,iso9660 user,noauto,exec,utf8 0 0
Fixing LIRC for Hauppauge remotes
Mythbuntu uses the incorrect lircrc for the Hauppauge remote, you should copy and paste the one from the Hauppauge WinTV Nova-T 500 PCI page. Save this as ~/.lircrc and make links from this to ~/.mythtv/lircrc and ~/.lircrc/mythtv
Another annoying problem stems from the "events" on the system. These don't stay put, so on one boot you'll have your receiver on event6, the next, it'll be event3. Obviously Lirc can't magically detect this for you, but luckily, other system processes can.
First you want to find the event the receiver is currently running on:
cat /proc/bus/input/devices | grep -iA4 receiver
Now, run the following command:
udevinfo -a -p $(udevinfo -q path -n /dev/input/[OUTPUT_FROM_ABOVE_COMMAND]) | grep -i vendor
Hopefully you'll get one line saying "SYSFS{vendor}="0x99999" or something to that effect, if you get more than one, then usually its the first you need. Now, using your favourite editor, open /etc/udev/rules.d/10-local.rules:
sudo mousepad /etc/udev/rules.d/10-local.rules
Add the following line:
KERNEL=="event*",SYSFS{vendor}=="0x99999",SYMLINK="lirc0"
Obviously this is bit you replace 0x99999 with the code you received from one of the above commands. Once this is done, restart the udev server:
/etc/init.d/udev restart
And voilas. To test, you can check the listing of lirc0;
ls -la /dev/lirc*
It should output "lirc0 --> event6" or whatever your receivers eventid is.
For reference: /etc/lirc/hardware.conf
# /etc/lirc/hardware.conf # REMOTE="Hauppauge TV Card" REMOTE_DEVICE="/dev/lirc0" REMOTE_DRIVER="devinput" REMOTE_MODULES="lirc_dev lirc_i2c" REMOTE_LIRCD_CONF="/etc/lirc/lircd.conf" REMOTE_LIRCD_ARGS="" START_LIRCD="true" LOAD_MODULES="true"
Recommended extra packages
If using wireless, install WICD!, this will enable mythbuntu to silently connect to your wireless network, without nagging you for keyrings, or d/cing after a sleep. To do this; add
#WICD, Wireless network manager deb http://apt.wicd.net hardy extras
to your /etc/apt/sources.list file. From this point, just run "sudo apt-get install wicd" and you should be good to go; you might need to add /opt/wicd/tray.py to your startup programs, to get a tray icon.
Also perhaps add wine, depending on how you use the machine, I personally run some windows games I own, so wine is helpful:
# Wine deb http://wine.budgetdedicated.com/apt gutsy main deb-src http://wine.budgetdedicated.com/apt gutsy main
Then apt-get install wine!
Mysql Crashing
It would be a good idea to get mythbuntu to repair the tables on reboot. Having to manually repair the tables when the box crashes is annoying, so why not automate. Add this to your system startup, whichever way you prefer:
mysqlcheck -umythtv -pPASSWORD --auto-repair mythconverg