Difference between revisions of "User:Sdkovacs"

From MythTV Official Wiki
Jump to: navigation, search
(My Setup on Fedora 8)
(My Setup on Fedora 8)
Line 1: Line 1:
==My Setup on Fedora 8==
==My Setup on CentOS 5.3==
===Capture Cards===
===Capture Cards===
Line 7: Line 7:
===System specs===
===System specs===
Celeron 1.3ghz 512MB RAM
Pentium 4 2.8ghz 1.2GB RAM
* Hard Drive 1 - 25GB
* Hard Drive 1 - 25GB
  ** /
  ** /
Line 18: Line 18:
Posted here is my xorg.conf file for the PVR350 with TVOUT. I had to change a few lines between Fedora 6 and Fedora 8 because of the change in the ivtv driver.

Revision as of 20:06, 15 September 2009

My Setup on CentOS 5.3

Capture Cards

PVR350 (using TV out)


System specs

Pentium 4 2.8ghz 1.2GB RAM

  • Hard Drive 1 - 25GB
** /
** /boot
** swap
  • Hard Drive 2 - 320GB
** /videos


# XFree86 4 configuration created by pyxf86config

Section "ServerLayout"
        Identifier     "Default Layout"
        Screen      0  "Screen0" 0 0
        InputDevice    "Mouse0" "CorePointer"
        InputDevice    "Keyboard0" "CoreKeyboard"

Section "Files"

# RgbPath is the location of the RGB database.  Note, this is the name of the
# file minus the extension (like ".txt" or ".db").  There is normally
# no need to change the default.
# Multiple FontPath entries are allowed (they are concatenated together)
# By default, Red Hat 6.0 and later now use a font server independent of
# the X server to render fonts.

#        ModulePath   "/usr/lib/xorg/modules/extensions/nvidia"
#        ModulePath   "/usr/lib/xorg/modules/extensions"
#        ModulePath   "/usr/lib/xorg/modules"
#        FontPath     "unix/:7100"

Section "Module"
        Load  "dbe"
        Load  "extmod"
        Load  "fbdevhw"
        Load  "glx"
        Load  "record"
        Load  "freetype"
        Load  "type1"
        Load  "vnc"

Section "InputDevice"

# Specify which keyboard LEDs can be user-controlled (eg, with xset(1))
#       Option  "Xleds"         "1 2 3"
# To disable the XKEYBOARD extension, uncomment XkbDisable.
#       Option  "XkbDisable"
# To customise the XKB settings to suit your keyboard, modify the
# lines below (which are the defaults).  For example, for a non-U.S.
# keyboard, you will probably want to use:
#       Option  "XkbModel"      "pc102"
# If you have a US Microsoft Natural keyboard, you can use:
#       Option  "XkbModel"      "microsoft"
# Then to change the language, change the Layout setting.
# For example, a german layout can be obtained with:
#       Option  "XkbLayout"     "de"
# or:
#       Option  "XkbLayout"     "de"
#       Option  "XkbVariant"    "nodeadkeys"
# If you'd like to switch the positions of your capslock and
# control keys, use:
#       Option  "XkbOptions"    "ctrl:swapcaps"
# Or if you just want both to be control, use:
#       Option  "XkbOptions"    "ctrl:nocaps"
        Identifier  "Keyboard0"
Driver      "kbd"
        Option      "XkbModel" "pc105"
        Option      "XkbLayout" "us"

Section "InputDevice"
        Identifier  "Mouse0"
        Driver      "mouse"
        Option      "Protocol" "IMPS/2"
        Option      "Device" "/dev/input/mice"
        Option      "ZAxisMapping" "4 5"
        Option      "Emulate3Buttons" "no"

Section "InputDevice"

# If the normal CorePointer mouse is not a USB mouse then
# this input device can be used in AlwaysCore mode to let you
# also use USB mice at the same time.
        Identifier  "DevInputMice"
        Driver      "mouse"
        Option      "Protocol" "IMPS/2"
        Option      "Device" "/dev/input/mice"
        Option      "ZAxisMapping" "4 5"
        Option      "Emulate3Buttons" "no"

Section "Monitor"
        Identifier  "NTSC Monitor"
        HorizSync  30-68
        VertRefresh 50-120
        Mode "720x480"
          # D: 34.563 MHz, H: 37.244 kHz, V: 73.897 Hz
          DotClock 34.564
          HTimings 720 752 840 928
          VTimings 480 484 488 504
          Flags    "-HSync" "-VSync"

Section "Device"
        Identifier  "Hauppauge PVR 350 iTVC15 Framebuffer"
        Driver      "ivtv"

        ### change fb1 to whatever your card grabbed
        Option      "fbdev" "/dev/fb1"
        Option      "ivtv" "/dev/fb1"

        ### change the BusID to whatever is reported by lspci,
        ### converted from hex to decimal
        BusID "PCI:2:10:0" # lspci says 02:0a.0
        #BusID "PCI:0:8:0" # lspci says 00:08.0
        ### More examples
        #BusID "PCI:0:10:0" # lspci says 00:0a.0
        #BusID "PCI:1:14:0" # lspci says 01:0e.0
        #BusID "PCI:0:5:1" # lspci says 00:05.1

Section "Screen"
        Identifier  "Screen0"
        Device      "Hauppauge PVR 350 iTVC15 Framebuffer"
        Monitor     "NTSC Monitor"
        Option "SecurityTypes" "VncAuth"
        Option "UserPasswdVerifier" "VncAuth"
        Option "PasswordFile" "/home/mythtv/.vnc/passwd"
        DefaultDepth 24
        DefaultFbbpp 32
        Subsection "Display"
          Depth 24
          FbBpp 32
          Modes "720x480"

Section "DRI"
        Group        0
        Mode         0666