Using an IR Blaster with MythTV
The mission: Get MythTV to change channels on my cable provided STB (set-top box). I connected a coax cable from the STB to my capture card, but with STBs one cannot tune/change stations using the tuner built into the capture card. The capture card should remain on channel 3, and I need an infrared emitter to send signals to my set-top box when Myth needs to change channels.
N.B. In the UK you can control your Sky or Sky+ box and some of the AUS Foxtel IQ boxes using a Dusky Control
You can build your own serial port IR emitter very inexpensively or you can buy one.
- irblaster.info - $12 - $15 - inexpensive serial IR blaster similar to what you might build yourself. You stick it with included double sided tape right to the STB pointing at the STB's IR reciever.
- Microsoft MCE USB remote combo - A usb remote and blaster combo. Works very well.
- CommandIR Mini - A hardware-based USB transceiver supporting multiple IR blasters or "emitters". Can simultaneously control set top boxes and receive remote control commands. Provides a free online MythTV support Mythtv.
- See the bottom for a growing list of vendors
Installing the IR Blaster
This is the serial IR blaster from irblaster.info
Use the links at the bottom of this page for detailed instructions. You will plug one end of the IR Blaster into a serial port on the Myth backend, and the other side with the diode is pointed at the STB. Normally you put it right over the STB's IR eye as pictured below from Geoff Holden's blog.
You have to load lirc_serial at boot. There are instructions in the HOWto links. The way I do it on Fedora is to edit modprobe.conf. Since you likely also have an IR receiver, such as on the hauppage cards, you need two lirc modules loaded, the lirc_i2c module for the IR receiver, and lirc_serial for the IR emitter. Again please see the details instructions in the links above.
Once the modules are loaded, you run two instances of the lirc daemon lircd. One instance uses device /dev/lircd0 and the other /dev/lircd1.
Configuring Myth Backend
Instructions in the HOWTO links show you how to make a channel change script. You need to use MythTV setup to tell Myth to use the script to change channels.
Run the mythtvsetup by opening an X window console and typeing mythtvsetup.
Once you have defined your input connection, select it and find the following setup page:
You will enter the command for changing channels here. Note the box "Preset Tuner to channel" which says 3. This is important, just as your TV has to be set to channel 3 to recieve signals from the STB, so does your PVR card. Furthermore, I found that this did not work. In order to actually tune my PVR-250 to channel 3 I used this command in my rc.local, which runs after startup:
ivtv-tune -c 3 -d /dev/video1
to change the PVR 250 to channel 3.
MyBlaster setup -- does not require LIRC
If you prefer not to have to mess around with LIRC there are alternatives. One of these is the MyBlaster serial. (See the vendor list below.) It is a commercial product but the linux drivers are GPL. The latest driver can be found on SourceForge. To set up, simply edit the perl based driver script for your port and device and call the script using the external channel change script configuration option in mythtv-setup. It is that easy.
Note that MythTV sends frequency IDs to the external channel changer script and not the channel number. If you see some weird four/five digit numbers being sent through the IR blaster, you will need to go to the channel editor in setup and change the freqid for the channels to match the ones that you expect to receive through the IR blaster.
When using the script and setup at http://losdos.dyndns.org:8080/public/mythtv-info/IR-BLASTER-HOWTO.html
- do not* be tempted to change the configure options to set COM1/IRQ4 in the pre-make configuration. Rather, follow the directions and pass those options through /etc/modules.conf or /etc/modprobe.d/aliases.
Changing the settings at the earlier stage will produce a module that conflicts with the standard lirc (and a frustrating string of errors in dmesg: ledxmit_dev: register_chrdev failed ledxmit_serial: Unknown symbol ledxmit_register_plugin).
Monitoring STB Status
As STBs are external devices, it is sometimes difficult to monitor their power state, depending on the make/model of the STB.
Refer this page for help to setup a STB monitoring script. For best results, make your channel changer script first call this, so that it gets unhindered read access to your ivtv device.
IR Blaster Vendors
In the USA
- IRblaster offer serial port IR blasters, as do:
- IguanaWorks sells long range serial IR blaster & receiver. Also sells Linux-compatible USB IR Trasceivers
- LIRC/MythTV EBay store with interesting IR blaster options. There are some kits for building your own IR transmitters.
- CommandIR Mini is a hardware-based USB multi-blaster supporting independent control of multiple devices via "emitters". Device receives & blasts simultaneously and they ship globally.
- Dvbshop.net sell IR remotes, receivers & blasters
- IRtrans sell IR transceivers (combined receiver/blaster) & LAN equipped units too
- RedEyeRemote They don't look much, but these IR transmitters work via serial port with NTL PACE and Samsung STBs.
- DuskyControl This is a USB device which connects to the RF2 port on your Sky or Sky+ box. There is a version with dual outputs to allow control of two boxes.